Sharp PG-C45X Selecting the Transmission Speed RS-232C, Canceling the Keylock Setting

Page 76

Locking the Operation Buttons on the Projector

Canceling the Keylock

Setting

When the Keylock Level is set to “Normal”, all buttons are functional.

Select “Keylock Level” in the “Options

(2)” menu on the menu screen and set “ Normal”.

➝For operating the menu screen, see pages 42 to 45.

Note

•When a password has been set, and “Keylock Level” is selected, the password input box will be displayed.

•If both a password and the Keylock Level have been set at the same time, the pass- word will be necessary before changing the Keylock Level.

Selecting the Transmission Speed (RS-232C)

This menu allows you to adjust the transmission speed of the RS-232C connection by select- ing the baud rate.

Selecting the Transmis- sion Speed (RS-232C)

Select “RS-232C” in the “Options (2)” menu on the menu screen.

➝For operating the menu screen, see pages 42 to 45.

Note

•When a password has been set, and “RS- 232C” is selected, the password input box will be displayed.

•Make sure that both the projector and computer are set for the same baud rate. Refer to the computer’s operation manual for instructions for setting the computer’s baud rate.

-72

Image 76

Contents PG-C45X Model No. PG-C45X Serial No Special Note for Users in the U.K Page Introduction Product Disposal Outstanding Features Color Management SystemNoise Reduction New Edge Up-ScalingContents Appendix Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check Wall or Ceiling MountingAvoid locations with high or low temperature Using the projector in other countriesTemperature monitor function Rest your eyes occasionallyTo install Acrobat Reader from the CD-ROM For other operating systems For other languagesFor Windows For MacintoshPart Names Projector Front and Top ViewUsing the Kensington Lock Projector Rear ViewRemote Control Top View Remote Control Front ViewPart Names Using the Remote Control Available Range of the Remote ControlWhen using the remote control Inserting the BatteriesSupplied accessories AccessoriesOptional cables Connections and Setup Connecting the Projector to Other Devices Before ConnectingThis projector can be connected to An audio cable commercially available SeeConnecting the Power Cord Connecting to a Computer Using the RGB Cable Ferrite corePlug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Connecting to Component Video Equipment CableConnecting to an Amplifier Connecting to an Amplifier or Other Audio ComponentsControlling the Projector by a Computer Connecting to a Monitor Watching Images on Both the Projector and a MonitorPress or while using presentation software on your computer Using the Wireless Pre- sentation FunctionButton Using as a Wired Remote Control Connecting the Remote Control to the ProjectorSetup Using the Adjustment FeetFocus ring Zoom knob Adjusting the LensOut Zoom Setting up the Screen Throw DistanceStretch Mode Normal ModeScreen Size and Projection Distance AN-C12MZ Throw ratio 11.18 to Projecting a Reversed/Inverted Image Projection from behind the screenBasic Operation Basic Procedure Plug the power cord into the wall outletPress on the projector or on the remote control Image ProjectionPress , , or on the remote control to select the Input mode Volume buttonsSelecting the On-screen Display Language Press to temporarily turn off the soundPress Press \ or to select LanPress or to select the de- sired language, and then press Press , , \ and to adjust the Keystone correction Correcting Trapezoidal DistortionKeystone button Enter button Undo button Buttons Test patternUndo button Menu Bar Items Sub menuInput 3 / 4 Mode Main menu Sub menuMenu Selections Adjustments Using the Menu ScreenMenu Bar Main Menu Enter button Buttons Menu button Press or to select the item you want to adjust Press \ or to select the menu you want to adjustPress \ or to adjust the item selected Press or to select the item you want to set Menu Selections SettingsEnter button Buttons Menu button Cursor shifts to the sub menu Adjusting Image Preferences Adjusting the PictureSelecting the Signal Type Progressive Mode When Auto Sync is OFF Adjusting Computer ImagesSaving Adjustment Settings Special Mode Settings Selecting Adjustment SettingsChecking the Input Signal Auto Sync Adjustment Auto Sync Display FunctionScreen display during Auto Sync Auto Sync buttonEasy to Use Functions Switching the Picture Display Using Different Input Signals Selecting the Picture Display ModeResize button Screen display of the picture display mode Video Freezing a Moving Image Displaying a Still ImageFreeze button Displaying an Enlarged Portion of an Image Enlarging a Specific Portion of an ImageButtons Enlarge Enlarge/ Reduce buttons Adjusting Gamma Correction Gamma Correction FunctionDisplaying the Inset Picture Displaying Dual Pictures Pict in PictPress to move the inset pic- ture Black Screen Function Blacking out the Pro- jected ImageTo return to the original projected image, press again This function can be used to display a black screenDisplaying the Break Timer Displaying and Setting the Break TimerPress to cancel the break timer Buttons Break Timer buttonSelecting the Color Reproduction Mode Selecting the Target ColorSetting the Chromatic Value of the Target Color Setting the Brightness of the Target ColorSetting the Hue of the Target Color Resetting User-Defined Color Settings Overview of All Color SettingsSetting the Audio Output Type Setting on/off the Internal SpeakerSetting the Audio Out- put Type Setting on/off the Inter- nal SpeakerUsing Auto Search Auto Search FunctionSetting On-screen Display Video Digital Noise Reduction DNR SystemReducing Image Noise Turning Off On-screen DisplaySetting the Video System Setting the Video SystemCapturing the Image Saving Projected ImagesDeleting the Captured Image Setting a Background Image Selecting a Startup ImageSelecting a Background Image Selecting a Startup ImageSetting the Power Save Mode Selecting the Economy ModeMonitor Out/RS-232C Off Function Automatic Power Off Function Selecting the Economy ModeDisplaying the Remaining Lamp Life Percentage Checking the Remaining Lamp Life PercentageSetting the Projection Mode Setting up the KeylockReversing/Inverting Projected Images Locking the Operation Buttons on the ProjectorSelecting the Transmission Speed RS-232C Canceling the Keylock SettingSelecting the Transmis- sion Speed RS-232C Setting up a Password Entering the PasswordChanging the Password If You Forget Your PasswordSetting the Anti-Theft Entering the KeycodeChanging the Keycode Enter the same 4-digit keycode in ReconfirmInitializing the Settings Returning to Default SettingsDisplaying the Adjustment Settings Overview of All Menu SettingsAppendix Maintenance Cleaning the projectorCleaning the lens Cleaning the exhaust and intake ventsCleaning and replacing the bottom air filter Turn off the power and discon- nect the power cordReplacing the Air Filter Remove the bottom filter coverReplace the air filter Clean the air filterReplace the filter cover About the temperature warning indicator Maintenance IndicatorsAbout the lamp replacement indicator Maintenance Indicators Lamp Regarding the LampReplacing the Lamp Removing and Install- ing the Lamp Unit Press on the projector to turn off the powerDisconnect the power cord Change the air filterResetting the Lamp Timer Connecting Pin Assignments RGB Input Component InputRS-232C Specifications and Command Settings CommandsPC control Communication conditionsRS-232C Specifications and Command Settings Options Control Contents Wired Remote Control Terminal Specifications Specifications of wired remote control inputSharp remote control signal format Function and transmisson codesComputer Compatibility Chart ComputerTroubleshooting Troubleshooting For Sharp Assistance Specifications Ntsc 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAMDimensions Units inches mmGlossary Advanced intelligent compressionIndex 100Stretch 101Sharp Corporation