Sharp PG-A10X operation manual Product Disposal, When Attaching the Quick Guide Label

Page 6

WARNING:

The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During normal operation, when turning the power off always use the POWER OFF button on the projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.

DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

PRODUCT DISPOSAL

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 57.

LAMP REPLACEMENT CAUTION

BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.

HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE

REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP UNIT

TYPE BQC-PGA10X//1 ONLY.

UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP

BEFORE SERVICING.

HIGH PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL

HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED.

HANDLE WITH CARE. SEE OPERATION MANUAL.

PRECAUTIONS A OBSERVER LORS

DU REMPLACEMENT DE LA LAMPE.

DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER

LA VIS. L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD,

ATTENDRE 1 HEURE AVANT DE PROCEDER AU REMPLACEMENT

DE LA LAMPE. NE REMPLACER QUE PAR UNE LAMPE SHARP DE

TYPE BQC-PGA10X//1.

RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.

ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.

LAMPE A HAUTE PRESSION : RISQUE D’EXPLOSION. DANGER

POTENTIEL DE PARTICULES DE VERRE EN CAS D’ECLATEMENT

DE LA LAMPE. A MANIPULER AVEC PRECAUTION, SE REPORTER

AU MODE D’EMPLOI.

When Attaching the “QUICK GUIDE” Label

Attaching the “QUICK GUIDE” Label (supplied) on the projector will help you check the setup procedure. When you attach the “QUICK GUIDE” Label on the projector, be sure to align the label bottom and the upper part of

the “Notevision” logo on the top cabinet of the projector

as shown in the drawing on the right. Do not attach the “QUICK GUIDE” Label “QUICK GUIDE” Label anywhere else.

-2

Image 6

Contents PG-A10X PG-A10S Model No Serial No Special Note for Users in the U.K Page Introduction When Attaching the Quick Guide Label Product DisposalOutstanding Features Light and Compact DesignContents Appendix Power Sources CleaningAccessories Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts Wall or Ceiling MountingTemperature monitor function Avoid locations with extremes of temperatureUsing the projector in other countries Rest your eyes occasionallyFor Windows To install Acrobat Reader from the CD-ROMFor other operating systems For other languages For MacintoshPart Names Projector Front and Top ViewUsing the Kensington Lock Projector Rear ViewRemote Control Front View FORWARD/BACK buttonsUsable Range Using the Remote ControlWhen using the remote control Inserting the BatteriesAccessories Supplied accessoriesOptional accessories Connecting the Power Cord Connecting the Projector to Other DevicesBefore Connecting This projector can be connected toConnecting to a Computer Using the RGB Cable Ferrite corePlug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Connecting to Component Video Equip- ment CableControlling the Projector Using a Computer Setup Using the Adjustment FeetAdjusting the Lens Focus ring Zoom knobSetting up the Screen Standard Setup Front ProjectionNormal Mode Stretch ModeScreen Size and Projection Distance Projecting a Reversed/Inverted Image Projection from behind the ScreenPress on the projector or on the remote control Basic ProcedurePlug the power cord into the wall outlet Power on button Volume buttons AV Mute button Input buttonsPress , or on the remote control to select the IN- PUT mode Press or on the remote control to adjust the volumeSelecting the On-screen Display Language Press , , \ and to adjust the Keystone correction Correcting Trapezoidal DistortionKeystone button Undo button Buttons Menu Items Main menu Sub menuInput 2 / 3 Mode PAL-NMenu Selections Using the Menu ScreenAdjustments Press \or to display the otherPress or to select the item you want to adjust Press \ or to adjust the item selectedPress \or to display the other menu screens SettingsMode is selected Button Menu button ButtonsSub menu Picture Adjustment Adjusting the ImageCLR Temp Adjusting Color Temperature Setting Signal Type Signal TypeSRGB sRGB Setting Memory Storing and Selecting Adjustment SettingsExample Fine Sync menu screen for Input 1 mode Computer Image AdjustmentAdjusting the Computer Special Modes Special Image Mode SettingsSignal Info Checking Input SignalPicture Display Mode Switching the Picture Dis- play ModeFunctions Button Buttons Press to cancel the operationStill and Zoom Image EnlargeLocking the Operation But- tons Taking the Keylock offUsing the Options Menu Lamp Timer Life Check OSD Display Setting OnIng the Lamp Life Status Screen Display Video System Video System SettingEco Mode Setting the Eco Mode Background Selecting a Startup and Background ImageMenu Position Selecting Auto Power Off AutoPower Off Function Menu Screen PositionPassword Setting a Pass- word If You Forget Your Pass- wordAnti-TheftSetting the Anti-Theft Easy to Use Functions Setting the Projection Mode Reversing/Inverting Projected ImagesHow to Use Carrying Case Carrying the ProjectorLens cap Cleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsReplacing the Air Filter Cleaning and Replacing the Air FilterTurn off the power and discon- nect the power cord Remove the filter/lamp unit coverReplace the air filter Clean the air filterTab User service screw Replace the filter/lamp unit coverMaintenance Indicators About the temperature warning indicatorMaintenance Indicators Regarding the Lamp LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitPress on the projector to turn off the power Power OFF button AC socket User Service Screw TabReset the lamp timer Resetting the Lamp TimerConnect the power cord Remove the lamp unitConnecting Pin Assignments RGB Input Component InputPC control RS-232C Specifications and Command SettingsCommands Communication conditionsComputer Compatibility Chart ComputerTroubleshooting 16-20Troubleshooting For Sharp Assistance Specifications NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAMDimensions Units inches mmGlossary Anti-TheftIndex BorderSharp Corporation