Sharp PG-A10X Removing and Installing the Lamp Unit, Press on the projector to turn off the power

Page 62

Regarding the Lamp

Removing and Installing the Lamp Unit

Info

•Be sure to remove the lamp unit using the handle. Be sure not to touch the glass sur- face of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.

•Do not loosen other screws except for the filter/lamp unit cover and lamp unit.

•Please refer to the installation manual in- cluded with the lamp unit.

1 Press on the projector to turn off the power.

•Wait until the cooling fan stops.

Warning!

•Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or in- jury.

2 Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3 Change the air filter.

•Change the air filter whenever you in- stall the lamp unit (see pages 53 and 54).

4 Remove the filter/lamp unit cover.

•Turn the projector over. Loosen the user service screw (1) that secures the fil- ter/lamp unit cover. Pressing the tab (2), remove the filter/lamp unit cover (3).

Lamp

unit	BQC-PGA10X//1

Power OFF button

AC socket

1

3

User

service

screw

2 Tab

-58

Image 62

Contents PG-A10X PG-A10S Model No Serial No Special Note for Users in the U.K Page Introduction When Attaching the Quick Guide Label Product DisposalOutstanding Features Light and Compact DesignContents Appendix Power Sources CleaningAccessories Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts Wall or Ceiling MountingTemperature monitor function Avoid locations with extremes of temperatureUsing the projector in other countries Rest your eyes occasionallyFor Windows To install Acrobat Reader from the CD-ROMFor other operating systems For other languages For MacintoshPart Names Projector Front and Top ViewUsing the Kensington Lock Projector Rear ViewRemote Control Front View FORWARD/BACK buttonsUsable Range Using the Remote ControlWhen using the remote control Inserting the BatteriesOptional accessories AccessoriesSupplied accessories Connecting the Power Cord Connecting the Projector to Other DevicesBefore Connecting This projector can be connected toConnecting to a Computer Using the RGB Cable Ferrite corePlug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Connecting to Component Video Equip- ment CableControlling the Projector Using a Computer Setup Using the Adjustment FeetAdjusting the Lens Focus ring Zoom knobSetting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Normal ModeStretch Mode Projecting a Reversed/Inverted Image Projection from behind the ScreenPress on the projector or on the remote control Basic ProcedurePlug the power cord into the wall outlet Power on button Volume buttons AV Mute button Input buttonsPress , or on the remote control to select the IN- PUT mode Press or on the remote control to adjust the volumeSelecting the On-screen Display Language Keystone button Undo button Buttons Press , , \ and to adjust the Keystone correctionCorrecting Trapezoidal Distortion Menu Items Main menu Sub menuInput 2 / 3 Mode PAL-NMenu Selections Using the Menu ScreenAdjustments Press \or to display the otherPress or to select the item you want to adjust Press \ or to adjust the item selectedPress \or to display the other menu screens SettingsMode is selected Button Menu button ButtonsSub menu CLR Temp Adjusting Color Temperature Picture AdjustmentAdjusting the Image Setting Signal Type Signal TypeSRGB sRGB Setting Memory Storing and Selecting Adjustment SettingsExample Fine Sync menu screen for Input 1 mode Computer Image AdjustmentAdjusting the Computer Special Modes Special Image Mode SettingsSignal Info Checking Input SignalPicture Display Mode Switching the Picture Dis- play ModeFunctions Button Buttons Press to cancel the operationStill and Zoom Image EnlargeLocking the Operation But- tons Taking the Keylock offIng the Lamp Life Status Screen Display Using the Options MenuLamp Timer Life Check OSD Display Setting On Video System Video System SettingEco Mode Setting the Eco Mode Background Selecting a Startup and Background ImageMenu Position Selecting Auto Power Off AutoPower Off Function Menu Screen PositionPassword Setting a Pass- word If You Forget Your Pass- wordAnti-TheftSetting the Anti-Theft Easy to Use Functions Setting the Projection Mode Reversing/Inverting Projected ImagesLens cap How to Use Carrying CaseCarrying the Projector Cleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsReplacing the Air Filter Cleaning and Replacing the Air FilterTurn off the power and discon- nect the power cord Remove the filter/lamp unit coverReplace the air filter Clean the air filterTab User service screw Replace the filter/lamp unit coverMaintenance Indicators About the temperature warning indicatorMaintenance Indicators Replacing the Lamp Regarding the LampLamp Disconnect the power cord Removing and Installing the Lamp UnitPress on the projector to turn off the power Power OFF button AC socket User Service Screw TabReset the lamp timer Resetting the Lamp TimerConnect the power cord Remove the lamp unitConnecting Pin Assignments RGB Input Component InputPC control RS-232C Specifications and Command SettingsCommands Communication conditionsComputer Compatibility Chart ComputerTroubleshooting 16-20Troubleshooting For Sharp Assistance Specifications NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAMDimensions Units inches mmGlossary Anti-TheftIndex BorderSharp Corporation