Shark PG-D4010X quick start Maintenance Indicators, About the temperature warning indicator

Page 57

Maintenance Indicators

■The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.

■If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below.

Top View

Power indicator Lamp indicator

Temperature warning indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising,

“” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter standby mode. When you fi nd the temperature warning indicator blinking, be sure to perform the measures described on page 54.

About the lamp indicator

■When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate in red.

■If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.

Indicators on the Projector

 

 

Power indicator

Red on

Normal (Standby)

 

 

Green on

Normal (Power on)

 

 

Red blinks

Abnormal (See page 54.)

 

 

Green blinks

Normal (Cooling)

 

 

Green and orange

The lens shutter is closed. (See page 29.)

 

 

blink alternately

 

 

Lamp indicator

Green on

Normal

 

 

Green blinks

The lamp is warming up.

Appendix

 

Red on

The lamp is shut down abnormally or requires to be

 

 

changed. (See page 54.)

 

Temperature

Off

Normal

 

warning indicator

 

 

 

Red on/Red blinks

The internal temperature is abnormally high. (See page 54.)

 

53

Page 56 Page 58
Image 57
Page 56 Page 58
Contents
PG-D4010X SetupModel No Serial No If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage Void the users authority to operate this equipment IntroductionENGLISHOnly A. onlyMaintenance Troubleshooting Index Using the Menu ScreenFor Future Reference Contents Reference Setting up the Projector Network Environment Network MenuPower Sources CleaningAccessories Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Closed Caption uses Bitstream Vera fontsSetup Manual When you want to view the Setup ManualFor Windows For MacintoshOptional accessories AccessoriesProjector Part Names and FunctionsTop View Front ViewUsing the Kensington Lock Using the Carrying HandleRear View TerminalsUP/PAGE COMPUTER, DVICLICK/EFFECT CLICK/RETURNRemote control signal transmitters Inserting the BatteriesUsable Range Quick Start Setup and ProjectionAdjust the projected image Setting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupExample 43 Signal Input Normal Mode Picture Size Projection PRJ Mode120 Projection DistanceSignal Input Normal Mode Signal Input Stretch ModeScreen Size and Projection Distance You may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Audio Controlling the Projector by a Computer When connecting to the LAN terminal using a LAN cable Connecting the Power CordAC socket Power cord SuppliedTurning the Projector On Turning the Projector On/OffAdjusting the Height Adjusting the Projected Image Adjusting the FocusAdjusting the Picture Size Image ProjectionPress P/Q or O/R to adjust Keystone Correction Press Keystone to enter the Keystone Correction modeCorrecting Trapezoidal Distortion Press KeystoneAdjusting the Volume Switching the Input ModeVIDEO, Video buttons AV Mute button VOL +/- Volume buttons On-screen displayResize Mode Press ResizeResize About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImageWhen moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingPicture menu Menu ItemsProjector adjustment PRJ-ADJ menu Screen adjustment SCR-ADJ menuHelp menu Network menuItems you can set with the Help menu Help menu nMenu Selections Adjustments Using the Menu ScreenPress Q or O and select Picture to adjust Press MENU/HELPPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press EnterSelecting the Picture Mode Picture Adjustment Picture MenuPAGE1 Menu operation nAdjusting the Color Temperature Adjusting the ImageAdjusting the Colors Adjusting Hue, Saturation, or ValueProgressive Reducing Image Noise DNREco+Quiet Setting the Resize Mode Adjusting the Projected Image SCR ADJ Menu2Adjusting the Image Position Setting the OverscanClosed Caption Setting the On-screen DisplaySelecting the Background Image Reversing/Inverting Projected ImagesAuto Power Off Function Auto Sync Auto Sync AdjustmentStandby Mode Auto Restart FunctionSpeaker Setting Audio Output Type SettingFan Mode Setting Selecting the Transmission Speed RS-232CChecking the Lamp Life Status When the System Lock is setEnter the same keycode in Re Confirm Input screen for keycodeKeylock Function Locking the Operation ButtonsTaking the Keylock off Select Password, then press Enter or Q Setting a Password Enter the same password in Reconfirm, then press Enter On the projector, pressDhcp Client Setting Setting up the Projector Network Environment Network MenuTCP/IP Setting Enter IP Address using P, R, Q and O, then press EnterExample When image flickering appears Troubleshooting with the Help MenuEnter button Adjustment buttons P/R/O/Q MENU/HELP button Utilizing the Help Menu FunctionsCleaning the projector MaintenanceCleaning the lens Cleaning the exhaust and intake ventsMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Red on Abnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp A onlyRemove the lamp unit cover Removing and Installing the Lamp UnitLamp unit AN-D400LPResetting the Lamp Timer Computer Computer Compatibility Chart21-25 Troubleshooting52, 53 Sharp Electronics Corporation Specifications Dimensions Index Kensington Security Standard connector ·················13
Top Page Image Contents