Vidikron 30ET manual Installing the Optional CineWide Lens Mount

Page 31

Installation

If you are installing a Vision 30/CineWide, proceed as follows to install the CineWide anamorphic lens base plate.

1. Do not install the CineWide lens yet, only the fixed CineWide base

Note plate. You will install the CineWide lens after you install the projector and adjust the primary lens.

2.Some components shipped with your projector may differ slightly from what is shown in these instructions.

To install the fixed CineWide base plate on a Vision 30/CineWide:

1.Place the projector upside down on a blanket or other soft surface.

2.If you are mounting the Vision 30/CineWide on a ceiling:

a Line up the four holes on the projector ceiling mounting plate (included with the projector ceiling mount kit) with those on the bottom of the projector.

b Line up the two mounting holes on the CineWide base plate with those at the front of the ceiling mounting plate.

3.Secure the CineWide base plate (and ceiling mounting plate, if needed) to the projector

with the required number of M6 x 1.0mm x 16mm screws: two for the lens base plate only, or four for the base plate and ceiling mounting plate. See Figure 3-4. TIGHTEN THE

SCREWS SECURELY, BUT DO NOT OVER-TIGHTEN THEM.

4.If you are mounting the Vision 30/CineWide on a ceiling: Complete the ceiling mount installation procedure given in the instructions provided with the ceiling mount kit.

3.5

Installing the Optional CineWide Lens Mount

Vision 30/CineWide with Ceiling Mounting

Vision 30/CineWide with Ceiling Mounting

Plate

Plate and Lens Base Plate

Figure 3-4. Vision 30/CineWide with Anamorphic Lens Base Plate and Ceiling Mounting Plate - Bottom View

Vidikron Vision 30 Series Owner’s Operating Manual

21

Page 30 Page 32
Image 31
Page 30 Page 32
Contents DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications OperationVision 30/CineWide with Anamorphic Lens Base Plate 1List of FiguresList of Figures About This Manual 1IntroductionThis Manual If you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories Vision 30 at a Glance POWER/STANDBY LED Indicates power status as followsIntake Vent Front IR Sensor Vidikron Logo Temp LEDProjection Lens BUILT-IN Keypad Connector PanelRefer to Vision 30 Connector Panel, below Main Power SwitchVision 30 Connector Panel RS-232 Control Port Built-In KeypadHdmi Digital Comp 2 / RGBVision 30 Remote Control Vision 30 Remote ControlHdmi RGB HDCinema DEF MEM1ISF NT ISF DAYRemote Control/Built-In Keypad Functional Cross-Reference Remote Control/Built-In Keypad Functional ComparisonControls and Functions Remote Control 3InstallationOperation Installation Overview Quick SetupStep Procedure For Details, Refer to Advantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeThrow Ratios for the Vision 30 Series Position Vertical and HorizontalMounting the Vision If you are mounting the Vision 30/CineWide on a ceiling Installing the Optional CineWide Lens MountScrews SECURELY, but do not OVER-TIGHTEN Them Connecting Source Connector Panel AccessConnections to the Vision Personal Computer Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc RS-232 Control System Connection ConnectionRemoving the Lens Cap Connecting to AC PowerChanging the OSD Language Adjusting the Picture Orientation Turning On the PowerZoom and Focus Adjustments Primary lens is perfectly centered on the screen Installing and Adjusting the CineWide Anamorphic LensLens Adjusting the Anamorphic Height Y Adjustment LensCorrect Lens Angle Incorrect Lens Angle Anamorphic Lens Top View Selecting an Aspect Ratio Selecting An Input Source Using Picture-In-Picture and Picture-By-Picture PIP/PBP4Operation Selecting Video MemoryUsing the On-Screen Menus Turning Off the PowerISF Main Menu Picture AdjustTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionDescription Aspect Ratio SettingsRemote Projector Status Exit to return to the previous menu or Menu to exit InstallationService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Communications Vision 30 Specifications 7SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsVidikron DimensionsSpecifications Personalizing the ISF Splash Screen on the Vision Power-cycle the projector to see the change Page RUMA-011140
Related manuals
Manual 58 pages 25.8 Kb

30ET, 30 specifications

Vidikron 30 is a standout in the world of high-performance projectors, designed primarily for home theater enthusiasts and professional installations. This model is known for its advanced technologies and exceptional image quality, catering to both casual viewers and serious cinephiles.

One of the most notable features of the Vidikron 30 is its native 4K resolution. This high pixel count ensures that images are incredibly sharp and detailed, making every frame come to life with stunning clarity. The projector utilizes advanced pixel-shifting technologies to enhance image fidelity, providing an immersive viewing experience that is hard to replicate.

The Vidikron 30 boasts an impressive contrast ratio, allowing for deep blacks and bright whites, which is crucial for experiencing the full dynamic range of films and shows. This feature is complemented by its superior color accuracy, featuring advanced color management systems that deliver vibrant and true-to-life colors. The projector is equipped with High Dynamic Range (HDR) capabilities, ensuring that users can enjoy a wide range of brightness levels.

Audio experience is another area where the Vidikron 30 excels. It is designed to support high-quality audio formats, making it compatible with several advanced surround sound systems. This harmony between visual and audio quality ensures an all-encompassing cinematic experience.

In terms of connectivity, the Vidikron 30 offers multiple input options, including HDMI, USB, and legacy connections, making it versatile and easy to integrate into various home theater setups. It also supports wireless streaming, allowing users to connect their devices effortlessly.

The design of the Vidikron 30 is sleek and sophisticated, fitting seamlessly into modern living spaces. Its silent operation feature is another bonus, enabling users to enjoy movies without disruptive noise from the projector itself.

Lastly, Vidikron provides a comprehensive support system for its projectors, including calibration services to ensure optimal performance and longevity.

In summary, the Vidikron 30 is a powerhouse of home projection technology, combining high resolution, superior contrast and color accuracy, and excellent audio support. Its elegant design and extensive connectivity options make it a top choice for anyone looking to achieve a premium home theater experience.
Top Page Image Contents