Vidikron 30ET manual Adjusting the Anamorphic Height Y Adjustment Lens

Page 40

Installation

Installing the Anamorphic

➤ 1.

Use the Pitch/Y-Adjustment Screws (item #7) and Fender Washers (item #6) to attach the

Lens

 

Mounting Brackets (item #2) to the Anamorphic Lens (item #3). (Do not fully tighten the

 

 

screws yet.)

 

2.

Use the two Yaw/Z-Adjustment Knobs (item #4) and Fiber Washers (item #5) to attach

 

 

the Anamorphic Lens assembly to the Base Plate (item #1).

To avoid clipping the corners of the image, position the anamorphic lens

Tip

as close as possible (ALWAYS within 0.25 inch or closer) to the primary lens.

 

 

0.25¨ max.

Adjusting the Anamorphic ➤ Height (Y) Adjustment:

Lens

1.

Project a white field on the screen.

 

 

2.

Ensure that the four Pitch/Y-Adjustment Screws are loose enough to allow movement of

 

 

the lens assembly.

 

3.

Slowly move the anamorphic lens into place so that there are no shadows on the top or

 

 

bottom of the screen:

Too Low

Correct position

Too High

4.When the height is properly set, tighten the top two Pitch/Y-Adjustment Screws to secure the lens in place.

Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. To do this, loosen the bottom two Pitch/Y-Adjustment Screws on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is rectangular:

30

Vidikron Vision 30 Series Owner’s Operating Manual

Page 39 Page 41
Image 40
Page 39 Page 41
Contents DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial Communications1List of Figures Vision 30/CineWide with Anamorphic Lens Base PlateList of Figures About This Manual 1IntroductionThis Manual Using This Manual If you need Turn toDescription, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 30 at a GlanceIntake Vent Front IR Sensor Vidikron Logo Temp LEDProjection Lens Connector Panel Refer to Vision 30 Connector Panel, belowMain Power Switch BUILT-IN KeypadVision 30 Connector Panel Built-In Keypad Hdmi DigitalComp 2 / RGB RS-232 Control PortVision 30 Remote Control Vision 30 Remote ControlHdmi RGB HDCinema MEM1 ISF NTISF DAY DEFRemote Control/Built-In Keypad Functional Comparison Remote Control/Built-In Keypad Functional Cross-ReferenceControls and Functions Remote Control 3InstallationOperation Installation Overview Quick SetupStep Procedure For Details, Refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsThrow Ratios for the Vision 30 Series Vertical and Horizontal PositionMounting the Vision If you are mounting the Vision 30/CineWide on a ceiling Installing the Optional CineWide Lens MountScrews SECURELY, but do not OVER-TIGHTEN Them Connecting Source Connector Panel AccessConnections to the Vision Personal Computer Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc Connection RS-232 Control System ConnectionConnecting to AC Power Removing the Lens CapChanging the OSD Language Adjusting the Picture Orientation Turning On the PowerZoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Primary lens is perfectly centered on the screenAdjusting the Anamorphic Height Y Adjustment Lens LensCorrect Lens Angle Incorrect Lens Angle Anamorphic Lens Top View Using Picture-In-Picture and Picture-By-Picture PIP/PBP 4OperationSelecting Video Memory Selecting an Aspect Ratio Selecting An Input SourceTurning Off the Power Using the On-Screen MenusISF Picture Adjust Main MenuPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionAspect Ratio Settings DescriptionRemote Projector Status Installation Exit to return to the previous menu or Menu to exitService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial CommunicationsSerial Communications Serial Commands Serial Communications 7Specifications Vision 30 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsDimensions VidikronSpecifications Personalizing the ISF Splash Screen on the Vision Power-cycle the projector to see the change Page RUMA-011140
Related manuals
Manual 58 pages 25.8 Kb

30ET, 30 specifications

Vidikron 30 is a standout in the world of high-performance projectors, designed primarily for home theater enthusiasts and professional installations. This model is known for its advanced technologies and exceptional image quality, catering to both casual viewers and serious cinephiles.

One of the most notable features of the Vidikron 30 is its native 4K resolution. This high pixel count ensures that images are incredibly sharp and detailed, making every frame come to life with stunning clarity. The projector utilizes advanced pixel-shifting technologies to enhance image fidelity, providing an immersive viewing experience that is hard to replicate.

The Vidikron 30 boasts an impressive contrast ratio, allowing for deep blacks and bright whites, which is crucial for experiencing the full dynamic range of films and shows. This feature is complemented by its superior color accuracy, featuring advanced color management systems that deliver vibrant and true-to-life colors. The projector is equipped with High Dynamic Range (HDR) capabilities, ensuring that users can enjoy a wide range of brightness levels.

Audio experience is another area where the Vidikron 30 excels. It is designed to support high-quality audio formats, making it compatible with several advanced surround sound systems. This harmony between visual and audio quality ensures an all-encompassing cinematic experience.

In terms of connectivity, the Vidikron 30 offers multiple input options, including HDMI, USB, and legacy connections, making it versatile and easy to integrate into various home theater setups. It also supports wireless streaming, allowing users to connect their devices effortlessly.

The design of the Vidikron 30 is sleek and sophisticated, fitting seamlessly into modern living spaces. Its silent operation feature is another bonus, enabling users to enjoy movies without disruptive noise from the projector itself.

Lastly, Vidikron provides a comprehensive support system for its projectors, including calibration services to ensure optimal performance and longevity.

In summary, the Vidikron 30 is a powerhouse of home projection technology, combining high resolution, superior contrast and color accuracy, and excellent audio support. Its elegant design and extensive connectivity options make it a top choice for anyone looking to achieve a premium home theater experience.
Top Page Image Contents