Motorola T3 Power Broadband manual Radio

Page 14

System Description

Radio

•802.11b/g

oBeacon frame control

oProbe request response

oBroadcast on/off per SDID

oListen mode client support

oDSS/OFDM modulation via 2.4Ghz transmitter

oRegulatory Domain: FCC Part 15c 15.247 and ETS 300 328

•Transmit power: 20dBm transmitter

oCustomer configurable: 1 – 14, max. In 1dBm increments

oMax transmit power of 20dBm depends on regulatory country

•Two integrated omni-directional antennas

o3.2dBi

oAntenna receive diversity

•Security Protocols – (per SSID)

oWireless Client Isolation

oWEP/WPA/WPA2 - Enterprise

o802.1x/EAP

oEAP types: TLS, PEAPv0, TTLS

oAES, TKIP encryption

•QoS

oWireless Multimedia (WMM) priority

oWMM power save

oSpectralink ready

•Virtual AP mode

oConcurrent BSS (16)

oPer-BSS SSID

oPer-BSS client isolation

oPer-BSS 802.1Q VLANs

oPer-BSS authentication/encryption

oPer-BSS bitrate

•Two runtime images in flash, realtime firmware upgrade

•Client state, status and statistics

oMAC address of client

oClient link rate

oClient link strength (dBm)

oPackets tx/rx

oAuthentication status

oSSID

oMAC address

•WLAN state information

oSignal strength and MAC of other APs

oTx signal strength

oPacket Tx/Rx statistics

Motorola, Inc.	570510-001-00 rev A	Page 14 of 50

Image 14

Contents T3 PowerBroadband Page RF Exposure Guidelines Regulatory Statements Model Number45225Frequency of Operation FCC and IC InternationalRadio Frequency Interference Requirements- FCC Marking and European Economic Area EEAT2-2500 and T3 Switch M2 WallPlateWaste Electrical and Electronic Equipment Weee Commands and Syntax Quality of Service QoS Administrative Commands Commands and SyntaxCommand Hierarchy Show CommandsStyle Conventions Global CommandsCommand Completion Interface Range System Description T3 PowerBroadband SwitchAdaptive Line Power M2 Ethernet WallPlateM2 Ethernet WallPlate Physical MC-802 Wireless WallPlateFeatures of the MC-802 802.11b/g radio Physical Radio Model Numbers and Description for related Products HardwareModel Numbers and Description Model Number Part Number DescriptionCross-Connect Connections Front ViewRear View Mounting OptionsM2 2 port Ethernet WallPlate LED Status LightsPage CLI Configuration Script files System AdministrationManagement Access Access MethodsConfiguration Files using the webUI File dirHttp Menus Upgrading the Firmware Wireless WallPlate FirmwareReboot the Wireless WallPlate to activate the new software T3 FirmwareLine Quality View System Configuration and Status Summary Startup RunningOther Configuration Help Commit modeReset to Default Configuration System config mode automanualmodeShow remote inventory Managing the Wireless WallPlatesWallPlate Inventory and Firmware Image Show remote imageIP Addresses Private IP addressPublic IP address Static IP address poolConfiguring a Wlan Global Radio CommandsExpanded Statistics and Status Per-WLAN CommandsMonitor the WLANs and radios Access Control Lists ACLs Ip access-list config 1 deny httpAuthenticating Clients using Radius network authenticated loginAuthenticating Administrative Access Configure the Radius ServerTools Required WallPlate InstallationBasic Configuration Components provided with the MC-802 WallPlateComponents required to purchase StepEnable line power Determine which port is being installedFinish the installation Enable line powerVlan terminology Vlan Specification802.1Q VLANs Tagged UntaggedVlan commands Tag-based Vlan Mode Port-based Vlan ModeWeb UI configuration Vlan General webUISet Vlan Egress Rules Tag-based Vlan webUICreate/Delete VLANs Set Vlan Ingress RulesPort-based Vlan webUI Quality of Service QoS QoS commands and conceptsNetwork qos interface queue interface-id mode mode Queue Dynamic packet classification802.1P bit Packet Classification CommandsQoS Example Packet transmissionLine Status Line Current Line Current Value Watts ReferenceAppendix a Pin-out Assignments Fast Ethernet WallPlate portsM2 WallPlate Appendix B Hardware SpecificationsT3 PowerBroadband MC-802 Wireless WallPlate