AMD SB750, 790GX user manual Onchip IDE Function

Page 33

(378H/IRQ7)

Line Printer port 1

Parallel Port Mode

 

SPP

: Standard Parallel Port

EPP

: Enhanced Parallel Port

ECP

: Extended Capability Port

SPP/EPP/ECP/ECP+EPP

To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the onboard parallel port to support both the ECP and EPP modes simultaneously. The ECP mode has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After selecting it, the following message will appear: “ECP Mode Use DMA” at this time, the user can choose between DMA channels 3 to 1. The onboard parallel port is EPP Spec. compliant, so after the user chooses the onboard parallel port with the EPP function, the following message will be displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP 1.9 spec. can be chosen.

Poweron After Power Failure

This determines the manner when the power recovery after power failure. The setting are: Off, On.

3-7-2 Onchip IDE Function

Phoenix – AwardBIOS CMOS Setup Utility

OnChip IDE Function

IDE HDD Block Mode

Enabled

Item Help

IDE DMA Transfer

 

Enabled

Onchip IDE Channel IO

Enabled

 

 

Primary Master

PIO

Auto

Menu Level >>

Primary Slave

PIO

Auto

 

Primary Master

UDMA

Auto

 

Primary Slave

UDMA

Auto

 

↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults

F7:Standard Defaults

IDE DMA transfer access

The integrated peripheral controller contains an IDE interface with support for one IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled.

Primary Master/Slave PIO

The two IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-2) for each of the two IDE devices that the onboard IDE interface supports. Modes 0 through 2 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device. The settings are: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.

Primary Master/Slave UDMA

28

Image 33
Contents AMD 790GX & AMD SB750 Based Environmental Protection Announcement Table of Content Reversion Revision History Date Forth Edition October Manual Revision InformationAMD K10 Processor Family Cooling SolutionsChapter Special Features of Motherboard Chipset DesignCPU Socket AM2+ Memory SocketPerformance Test Report Performance ListRear I / O for AMD790GX based Motherboard Layout DiagramJumpers Checking Motherboard’s Jumper Setting Hardware installation StepsKeyboard/USB function Enabled/Disabled JP1 Cmos RAM Clear 3-pin JbatGlossary Install CPUAbout AMD Athlon64 Socket AM2+ CPU Install Memory Valid Memory Configurations Bank Pin DimmTotal Memory Priority Standard function Expansion CardsConnectors Connectors, HeadersPower Connector 24-pin block ATXPWR1 PCI Express SlotPS/2 Mouse & PS/2 Keyboard Connector KB ATX 12V Power Connector 8-pin block ATX12VUSB Port connector CN1/ UL1 for USB LAN Port connector UL1 for RJ45 LANFloppy drive Connector 34-pin block FDD Microphone ConnectorAudio input to sound chip Audio output to speakerSub 15-pin Connector VGA1 Digital Visual Interface DVIHigh-Definition Multimedia Interface Hdmi Headers 10IR infrared module Headers 5-pin IR CD Audio-In Headers 4-pin CDIN1HDMI-SPDIF Out header Spdif Out Beep Meaning Starting Up Your ComputerEntering Setup Press F1 to continue, or Del to enter SetupGetting Help Main Menu Standard Cmos Features Hard Disk Boot Priority Advanced Bios FeatureEnabled default Enable cache Disabled Disable cache Virus WarningFirst/Second/Third/Fourth Boot Device Quick Power On Self-TestBoot Up Floppy Seek Boot Up NumLock StatusPcie Configuration Advanced Chipset FeaturesSystem Bios Cacheable Primary Dul Slot ConfigIGX Engine Clock Override IGX ConfigurationSuper IO Device Integrated PeripheralsOnchip IDE Function Onchip PCI Device Power Management Setup Miscellaneous Configuration PS CPU Smart FAN Configurations Shutdown TemperaturePC Health Status Show PC Health in PostCPU Voltage at Next Boot Power User Overclock SettingCPU Vcore 7---SHIFT CPU VcoreNB Voltage IH Flow-Control ModeDram Configuration CPU FeatureRAS-to-CAS Delay CAS # LatencyLoad Optimized Defaults Load Fail-Safe DefaultsPassword Settings Thermal Throttling OptionsEnter Password Chapter Sound Install ALC888 HD Codec Audio Driver Install ATI Driver PackPage RAID Install ATI Sata Driver and Utility LAN Install LANInstall PC-CILLIN 2007 Anti-virus program 6PC-HEALTH Install MyGuard Hardware monitor Utility HOW to Update BiosAMD Platform RAID Function Installation Jbod Page Pro Magic Plus Function Introduction Making RAID driver diskette before Install WindowsXP/2000What functions does Pro Magic Plus have? Page Appendix Reserved Initialize Video Verify 8259 Channel 1 masked interrupts by RAM Quick Post Codes S4 Post Codes BootBlock Post Codes Boot Load boot sector