AMD GA-M61SME-S2 NV Sata RAID function, NV Sata 1 Primary RAID, NV Sata 1 Secondary RAID

Page 37

NV SATA RAID function

Enabled	Enable NV SATA RAID function.
Disabled	Disable NV SATA RAID function. (Default value)

NV SATA 1 Primary RAID

Enabled	Enable NV SATA 1 primary RAID function.
Disabled	Disable this function. (Default value)

NV SATA 1 Secondary RAID

Enabled	Enable NV SATA 1 secondary RAID function.
Disabled	Disable this function. (Default value)

On-Chip IDE Channel0

Enabled	Enable onboard 1st channel IDE port. (Default value)
Disabled	Disable onboard 1st channel IDE port.

On-Chip MAC Lan

Auto	Auto-detect onboard LAN chip function. (Default value)
Disabled	Disable onboard LAN chip function.

NV Serial-ATA 1

Enabled	Enable NV Serial-ATA 1 function. (Default value)
Disabled	Disable this function.

IDE Prefetch Mode

Enabled	Enable IDE data buffer to enhance HDD transfer speed. (Default value)
Disabled	Disable IDE data buffer for the system stability.

USB Memory Type

SHADOW	Set USB memory type to SHADOW. (Default value)
Base Memory(640K)	Set USB memory type to base memory(640 K).

Onboard Audio Function

Auto	Auto-detect onboard audio function. (Default value)
Disabled	Disable this function.

Onboard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled	Enable this function.
Disabled	Disable this function. (Default value)

Onboard Serial Port 1

Auto	BIOS will automatically setup the Serial port 1 address.
3F8/IRQ4	Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
2F8/IRQ3	Enable onboard Serial port 1 and address is 2F8/IRQ3.
3E8/IRQ4	Enable onboard Serial port 1 and address is 3E8/IRQ4.
2E8/IRQ3	Enable onboard Serial port 1 and address is 2E8/IRQ3.
Disabled	Disable onboard Serial port 1.

- 37 -

BIOS Setup

Image 37

Contents GA-M61SME-S2 Motherboard Product Manual Classification CopyrightTable of Contents Regulatory Statements Box Contents GA-M61SME-S2 Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerFeature Summary Bios Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion CardsGV-RX60P128DE PCI Express x16 Graphics Card Support ListI/O Back Panel Introduction Line Out Front Speaker Out Connectors IntroductionMIC ATX12V/ATX Power Connector IDE IDE Connector Cpufan / Sysfan Cooler Fan Power ConnectorSataii 0 / Sataii 1 Sata 3Gb/s Connectors FDD FDD ConnectorFpanel Front Panel Jumper PwrledFaudio Front Audio Connector Spdifio S/PDIF In/Out Connector Cdin CD In ConnectorFUSB1 / FUSB2 / Front USB Connectors Hdasur Surround Center ConnectorCI Chassis Intrusion, Case Open Comb Comb ConnectorClrcmos Clear Cmos BatteryGA-M61SME-S2 Motherboard Main Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example Bios Ver. E7F12Boot Menu „ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master, Slave TimeIDE Channel 2/3 Master Drive a Floppy 3 Mode Support for Japan AreaHalt on MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check HDD S.M.A.R.T. Capability Away ModeInit Display First Frame Buffer SizeIntegrated Peripherals Onboard LAN Boot ROM IDE Prefetch ModeNV Sata RAID function NV Sata 1 Primary RAIDECP Mode Use DMA Parallel Port ModeOnboard Parallel Port On-Chip USBPower Management Setup Hpet Mode Note Power-On by AlarmPower On By Mouse Power On By KeyboardPCI 1 IRQ Assignment PnP/PCI ConfigurationsPCI 2 IRQ Assignment System/CPU Warning Temperature Current System/CPU TemperatureCase Opened Current VoltageV Vcore/DDR2 1.8V/+3.3V/+12VCPU Smart FAN ControlNote CPU Smart FAN ModeLoad Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationGA-M61SME-S2 Motherboard EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionBoot from CD/DVD System requirementsPrecautions Main Screen of Xpress Recovery2Limitations Updating the Bios Flash Bios Method IntroductionMethod 1 Q-FlashTM Before UseCopy Bios completed Pass Please press any key to continue Methods and steps Method 2 @BIOSTM UtilityPage Before you begin Installing Sata hard drives in your computerShadow Step Save and exit Bios Setup GA-M61SME-S2 Motherboard Configuring RAID set in RAID Bios YES BBS Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2- / 4- / 6- / 8- Channel Audio Introduction Installing the 5.1/7.1 Surround Cable OptionalAudio Jacks Introduction HD Audio Setting Up Stereo SpeakersSetting Up 4-Channel Audio Setting Up 6-Channel Audio Setting Up 8-Channel Audio Sound Effect Configuration Frequently Asked Questions TroubleshootingStart Troubleshooting ProcedureEND Regulatory Notices Weee Symbol StatementOur Commitment to Preserving the Environment China Restriction of Hazardous Substances Table Taiwan Headquarters Contact UsPoland Ukraine Romania Serbia & Montenegro Gigabyte Global Service System