Analog Devices ADSP-21364 system manual Default Configuration

Page 26

Default Configuration

Figure 1-1. EZ-KIT Lite Hardware Setup

3.Plug the provided power supply into J7 on the EZ-KIT Lite board. Visually verify that the green power LED (LED10) is on. Also verify that the red reset LED (LED9) goes on for a moment and then goes off, and, finally, LED1 through LED8 are blinking sequentially.

4.Connect one end of the USB cable to an available full speed USB port on your PC and the other end to ZJ1 on the ADSP-21364 EZ-KIT Lite board.

1-4	ADSP-21364 EZ-KIT Lite Evaluation System Manual

Image 26

Contents ADSP-21364 EZ-KIT Lite Evaluation System Manual Copyright Information Limited WarrantyTrademark and Service Mark Notice DisclaimerRegulatory Compliance Page Contents Using ADSP-21364 EZ-KIT Lite ADSP-21364 EZ-KIT Lite Evaluation System Manual Vii Index Preface Page Preface Purpose of This Manual Purpose of This ManualIntended Audience Manual Contents What’s New in This Manual What’s New in This ManualTechnical or Customer Support MyAnalog.com Supported ProcessorsProduct Information Product Information Processor Product InformationRelated Documents Online Technical Documentation Related VisualDSP++ PublicationsAccessing Documentation From VisualDSP++ Accessing Documentation From WindowsVisualDSP++ Documentation Set Accessing Documentation From WebPrinted Manuals Notation Conventions Hardware Tools Manuals Data SheetsNotation Conventions Processor ManualsADSP-21364 EZ-KIT Lite Evaluation System Manual Xxi Notation Conventions Using ADSP-21364 EZ-KIT Lite Package Contents Default Configuration Using ADSP-21364 EZ-KIT LiteDefault Configuration Installation and Session Startup Installation and Session Startup Evaluation License Restrictions External MemoryAnalog Audio Analog AudioUsing ADSP-21364 EZ-KIT Lite LEDs and Push Buttons LEDs and Push ButtonsProcessor Pin Mapped as Flag Example Programs Example ProgramsBackground Telemetry Channel ADSP-21364 EZ-KIT Lite Hardware Reference System Architecture System ArchitectureParallel Port ADSP-21364 EZ-KIT Lite Hardware ReferenceDEC DAI Interface Flag Pins SPI InterfaceIO Flag Pins Expansion InterfaceJtag Emulation Port Switch Settings Electret Microphone Select Switch SW6Codec Setup Switch SW7 Switch SettingsSPI Disable Switch SW8 Push Button Enable Switch SW9Boot Mode and Clock Ratio Select Switch SW10 Loop-Back Test Switch SW11 General Purpose LEDs LED8-1 Reset LED LED9Power LED LED10 USB Monitor LED ZLED3Board Reset Push Button SW5 Push Buttons SW1-4Expansion Interface J1-J3 ConnectorsConnectors Headphone Out Jack J6 Audio In RCA Connector J4Audio Out RCA Connector J5 Power Jack J7 Pdif Coax Connectors J8 and J9DAI Header P3 USB Connector ZJ1SPI Header P2 Jtag Header ZP4 ADSP-21364 EZ-KIT Lite Bill of Materials FDC658P ADSP-21364 EZ-KIT Lite Bill Of Materials Vishay CRCW080510K0JNEA Panasonic ERJ-8GEYJ101V Vishay CRCW12061K65FKEA Vishay CRCW080564K9FKEA Vishay CRCW1206100KFKEA ADSP-21364 EZ-KIT Lite Schematic DSP OSC Engineer to Engineer Note EE-68 which can be found at2Mb SramRight RED Disconnects Signals from SPI Flash and AD1835ADC DAC1 DAC2 DAC3 DAC4 AD1835 AudioDAC1 Left DAC2 Left DAC1 Right DAC2 RightDAC3 Left DAC4 Left DAC3 Right DAC4 RightADC Left DAC4 ADC RightOUT Spdif Coax InputCoax Analog SPI Header Expansion Interface Type aHeader Power FDC658PIndex Index Pdif USB