Alcatel-Lucent 6300-24 manual Rack Mounting, To rack-mount devices

Page 31

Mounting 3

Mounting

A switch unit can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. Mounting instructions for each type of site follow.

Rack Mounting

Before rack mounting the switch, pay particular attention to the following factors:

•Temperature: Since the temperature within a rack assembly may be higher than the ambient room temperature, check that the rack-environment temperature is within the specified operating temperature range. (See page C-1.)

•Mechanical Loading: Do not place any equipment on top of a rack-mounted unit.

•Circuit Overloading: Be sure that the supply circuit to the rack assembly is not overloaded.

•Grounding: Rack-mounted equipment should be properly grounded. Particular attention should be given to supply connections other than direct connections to the mains.

To rack-mount devices:

1.Attach the brackets to the device using the screws provided in the Bracket Mounting Kit.

1 3

2 4

5

6

	1000=Green
7	9
		11

8	10
		12

10/100=Y
	ellow
13	15
	15	17
		17	19
			19	21
				21
14	16
	16	18
		18	20
			20	22
				22

23

24

Link/

Act

FDX

Link/

Act

FDX

Power

Diag

BPS

OmniStac 6300-24k

Console

Figure 3-2. Attaching the Brackets

3-3

Image 31

Contents Part No -10, Rev. a December OmniStackPage Page Page Compliances and Safety Warnings Industry Canada Class B Vii Safety ComplianceUnderwriters Laboratories Compliance Statement Warnhinweis Faseroptikanschlüsse Optische SicherheitViii Wichtige Sicherheitshinweise GermanyDocumentation Environmental StatementEnd of Product Life Span Manufacturing MaterialsRelated Publications PurposeContents Glossary Index Appendix a TroubleshootingAppendix C Specifications Appendix B CablesTables Tables Xii Figures Figures Xiv Network Management Options Switch ArchitectureIntroduction OverviewIntroduction Description of Hardware10/100/1000BASE-T Ports SFP SlotsPort Status LEDs Status LEDsCondition Status System LEDs System Status LEDs Power Supply Receptacles Optional Backup Power SupplyFeatures and Benefits Management Network Planning Introduction to SwitchingCollapsed Backbone Application ExamplesNetwork Planning Network Aggregation Plan Network Aggregation PlanRemote Connection with Fiber Cable Remote Connection with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Selecting a Site Installing the SwitchEthernet Cabling Package Contents Equipment ChecklistOptional Rack-Mounting Equipment To rack-mount devices MountingRack Mounting MountingDesktop or Shelf Mounting Installing the Switch in a RackInstalling an Optional SFP Transceiver into the Switch Connecting to a Power SourcePower Receptacle Connecting to the Console PortSerial Cable Wiring Switch’s 9-Pin Null Modem PC’s 9-Pin Wiring Map for Serial CableDTE Port Installing the Switch Twisted-Pair Devices Connecting to PCs, Servers, Hubs and SwitchesConnecting Network Devices Making Network ConnectionsMaking Network Connections Network Wiring ConnectionsMaking LC Port Connections Fiber Optic SFP DevicesMbps Gigabit Ethernet Collision Domain ConnectorConnectivity Rules 1000BASE-T Cable RequirementsMbps Ethernet Collision Domain Mbps Fast Ethernet Collision Domain100 m 328 ft RJ-45 Cable Labeling and Connection Records Installation Appendix a TroubleshootingDiagnosing Switch Indicators Power and Cooling ProblemsTroubleshooting Twisted-Pair Cable and Pin Assignments Appendix B Cables10BASE-T/100BASE-TX Pin Assignments Cables 1000BASE-T Pin AssignmentsFiber Standards B Fiber StandardsCables Physical Characteristics Appendix C SpecificationsCompliances SpecificationsCE Mark Glossary-1 GlossaryGlossary-2 GlossaryGlossary-3 LEDGlossary Glossary-4 Index-1 IndexIndex-2 IndexPage 060190-10