Alcatel-Lucent 6300-24 manual Compliances and Safety Warnings

Page 5

Compliances and Safety Warnings

FCC - Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that the inter- ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient the receiving antenna

•Increase the separation between the equipment and receiver

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

•Consult the dealer or an experienced radio/TV technician for help

EC Conformance Declaration - Class B

SMC contact for these products in Europe is:

SMC Networks Europe, Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a, 08970 - Sant Joan Despí, Barcelona, Spain.

This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:

RFI Emission:

• Limit class B according to EN 55022:1998, IEC 60601-1-2 (EMC,

 

 

medical)

 

• Limit class A for harmonic current emission according to

 

 

EN 61000-3-2/1995

 

• Limitation of voltage fluctuation and flicker in low-voltage supply system

 

 

according to EN 61000-3-3/1995

Immunity:

•

Product family standard according to EN 55024:1998

 

• Electrostatic Discharge according to EN 61000-4-2:1995

 

 

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

 

• Radio-frequency electromagnetic field according to EN 61000-4-3:1996

 

 

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

 

•

Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC

 

 

power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995 (AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

v

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Part No -10, Rev. a December OmniStackPage Page Page Compliances and Safety Warnings Industry Canada Class B Underwriters Laboratories Compliance Statement Safety ComplianceWarnhinweis Faseroptikanschlüsse Optische Sicherheit ViiViii Wichtige Sicherheitshinweise GermanyEnd of Product Life Span Environmental StatementManufacturing Materials DocumentationRelated Publications PurposeContents Appendix C Specifications Appendix a TroubleshootingAppendix B Cables Glossary IndexTables Tables Xii Figures Figures Xiv Introduction Switch ArchitectureOverview Network Management Options10/100/1000BASE-T Ports Description of HardwareSFP Slots IntroductionCondition Status Status LEDsPort Status LEDs System LEDs System Status LEDs Features and Benefits Optional Backup Power SupplyPower Supply Receptacles Management Network Planning Introduction to SwitchingNetwork Planning Application ExamplesCollapsed Backbone Network Aggregation Plan Network Aggregation PlanRemote Connection with Fiber Cable Remote Connection with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Ethernet Cabling Installing the SwitchSelecting a Site Optional Rack-Mounting Equipment Equipment ChecklistPackage Contents Rack Mounting MountingMounting To rack-mount devicesDesktop or Shelf Mounting Installing the Switch in a RackInstalling an Optional SFP Transceiver into the Switch Connecting to a Power SourcePower Receptacle Connecting to the Console PortDTE Port Wiring Map for Serial CableSerial Cable Wiring Switch’s 9-Pin Null Modem PC’s 9-Pin Installing the Switch Connecting Network Devices Connecting to PCs, Servers, Hubs and SwitchesMaking Network Connections Twisted-Pair DevicesMaking Network Connections Network Wiring ConnectionsMaking LC Port Connections Fiber Optic SFP DevicesConnectivity Rules Connector1000BASE-T Cable Requirements Mbps Gigabit Ethernet Collision Domain100 m 328 ft RJ-45 Mbps Fast Ethernet Collision DomainMbps Ethernet Collision Domain Cable Labeling and Connection Records Diagnosing Switch Indicators Appendix a TroubleshootingPower and Cooling Problems InstallationTroubleshooting 10BASE-T/100BASE-TX Pin Assignments Appendix B CablesTwisted-Pair Cable and Pin Assignments Cables 1000BASE-T Pin AssignmentsFiber Standards B Fiber StandardsCables Physical Characteristics Appendix C SpecificationsCE Mark SpecificationsCompliances Glossary-1 GlossaryGlossary-2 GlossaryGlossary-3 LEDGlossary Glossary-4 Index-1 IndexIndex-2 IndexPage 060190-10
Top Page Image Contents