AMX instruction manual Rack-mounting the AXB-232++ optional, Replacing the Lithium Batteries

Page 12

Installation and Wiring

Rack-mounting the AXB-232++ (optional)

To rack-mount the AXB-232++ into the optional AC-RK Accessory Rack Kit:

1.Remove any connected power, and AXlink and RS-232 connectors from the rear panel.

2.Remove the two screws on the front panel of the AXB-232++.

3.Remove the front panel and space bracket behind the panel.

4.Place the unit in the appropriate opening in the AC-RK.

5.Place the front panel of the AXB-232++ on the front of the rack, over the unit.

6.Fasten the front panel to the rack and unit with the two screws you removed.

Replacing the Lithium Batteries

The AXB-232++’s lithium batteries have a life of approximately 5 years to protect its memory. When DC power is on, the batteries are not used. When you install the AXB-232++, record the date the batteries should be replaced.

There is a danger of explosion if you replace the batteries incorrectly. Replace batteries with the same or equivalent type recommended by the manufacturer. Dispose of the used batteries according to the manufacturer’s instructions. Never recharge, disassemble, or heat batteries above 212°F (100°C). Never solder directly to the batteries or expose the contents of the batteries to water.

Before removing the lithium batteries, contact your dealer and verify that they have a current copy of your program to avoid an inadvertent loss of data and prevent an unnecessary service outage.

1.Discharge the static electricity from your body.

2.Unplug the two-pin power connector and any other connectors.

3.Remove the two screws on the front panel.

4.Remove the front panel, and slide the circuit board out of the enclosure.

5.Carefully slide each battery out of its socket (FIG. 10), and insert the new battery.

Battery (CR2032 type - 20mm coin cell)

socket

FIG. 10 Lithium battery and socket

6.Slide the circuit board back into the enclosure.

7.Replace the front panel and refasten the two screws.

8.Reconnect any connectors that you removed.

 

8

AXB-232++ RS-232/422/485 Interface

 

 

 

Page 11 Page 13
Image 12
Page 11 Page 13
Contents AXB-232++ Page Table of Contents Table of Contents Product Information Front PanelRear Panel Specifications SpecificationsFront Panel Rear PanelInstallation and Wiring Setting the Internal JumpersSetting jumper JP4 to terminate RS-422 input with 100 ohms Setting the DIP Switches Setting jumper JP5 to set the RS-422 port for RS-485 useSetting the Device DIP switch Device DIP Switch SettingsSetting the RS-232/422 DIP switch RS-232/422 DIP Switch SettingsSetting FunctionWiring Devices to the AXB-232++ Preparing captive wiresWiring guidelines Using AXlinkUsing RS-232 Using Hardware HandshakingUsing RS-422 Using RS-485Rack-mounting the AXB-232++ optional Replacing the Lithium BatteriesSendCommands AXB-232++ SendCommandsProgramming Sendcommand AXB232,CHARD-10 Sendcommand AXB232,CTSPSHSendcommand AXB232,CTSPSHF Sendcommand AXB232,EOFFAxcess program characteristics SendString Escape Sequences SendString Escape SequencesAXB-232++ Program Statements AXB-232++ Program StatementsXmodem Timing Commands Xmodem Timing CommandsAXlink Master Statements AXlink Master StatementsAxcess Master Mode Reserved ChannelsReserved Channels Channel FunctionRevisionLast09/12/05

AXB-232++ specifications

The AMX AXB-232++ represents a significant advancement in the realm of high-performance vehicles, showcasing cutting-edge technologies and innovative features designed for enthusiasts and professionals alike. This model, known for its robust engineering and sophisticated design, positions itself as a versatile option in the competitive automotive landscape.

One of the standout features of the AMX AXB-232++ is its powerful engine. The vehicle is equipped with a turbocharged inline-six engine capable of producing impressive horsepower and torque, which allows for remarkable acceleration and responsiveness. This performance is further enhanced by the advanced transmission system that offers smooth gear shifts and adaptive performance, ensuring optimal power delivery across various driving conditions.

In terms of design, the AXB-232++ exudes a modern and aerodynamic aesthetic. The vehicle’s exterior incorporates sleek lines and aggressive contours, which not only contribute to its striking appearance but also improve aerodynamics. The dynamic front grille and LED headlamps further emphasize its bold character, while the customizable paint options allow for personalization to reflect the owner’s style.

The interior of the AMX AXB-232++ is equally impressive, combining luxury with functionality. The cockpit is designed with driver-centric ergonomics in mind, featuring high-quality materials and advanced tech integrations. The infotainment system is equipped with a user-friendly interface, providing access to navigation, music, and connectivity features. Premium sound systems and customizable lighting options enhance the overall driving experience.

Safety is a top priority for the AMX AXB-232++, and this model comes equipped with a suite of advanced safety technologies. This includes adaptive cruise control, lane-keeping assist, and a comprehensive airbag system, all designed to enhance driver and passenger safety. Furthermore, the AXB-232++ offers semi-autonomous driving capabilities, showcasing its commitment to incorporating innovative technology in its design.

In summary, the AMX AXB-232++ is a compelling blend of power, luxury, and advanced technology. With its high-performance engine, sophisticated interior, and comprehensive safety features, it stands out as a remarkable choice for those seeking a high-end vehicle that does not compromise on performance or comfort. Whether on the racetrack or the open road, the AXB-232++ promises an exhilarating driving experience defined by precision and style.
Top Page Image Contents