AMX Octaire Cabling & Setup for Vertical Interval Sync, Cable Requirement for VIS

Page 37

Installation & Setup

Cabling & Setup for Vertical Interval Sync

The Vertical Interval Sync (VIS) signal provides complete vertical interval synchronization switching capability for an Octaire system.

The VIS function uses an external master sync signal, such as station master, blackburst, or composite video input. When all of the source devices are genlocked to the same source, the master sync signal synchronizes the video switching to occur during the vertical interval (pulse), eliminating vertical roll or jitter on the monitor. The master sync signal also synchronizes all video switching for systems with multiple enclosures.

The VIS “Sync In” connector on the primary enclosure must be attached to an external sync source generating one of the following signal types:

Blackburst generator NTSC composite video

The VIS (BNC) connectors “Sync In” and “Sync Out” are to the far right on the rear of the enclosure.

Cable Requirement for VIS

75 ohm coax video cable (customer provided)

Cabling a Composite Enclosure for VIS

To send the sync signal to a composite enclosure:

1.Attach the external sync cable from the signal source to the Sync In connector on the right rear of the enclosure (FIG. 23).

Flip appropriate VIS toggle switches (see page 33)

From external sync source

FIG. 23 Attach external sync cable to Sync In connector

2.Flip the appropriate VIS toggle switches to the left for the sync signal type being used (see page 33).

Cabling a Multi-Enclosure System for VIS

When linking sync cable from enclosure to enclosure, use the upper sync connector for the incoming sync signal and the lower sync connector for the outgoing sync signal on each video enclosure.

To send the sync signal to a multi-enclosure System:

1.Attach a cable from the external sync source to the primary enclosure’s Sync In connector (FIG. 24) on the right rear. (The primary enclosure is the one with the control panel.)

32

Octaire Instruction Manual

Image 37
Contents Octaire AMX Limited Warranty and Disclaimer Software License and Warranty Agreement Contents APWeb Controlling the Octaire ESD Warning Important Safety Information & Instructions Information et directives de sécurité importantes Liability Notice Copyright NoticeUsfcc Notice Lithium Batteries NoticeTrademark Notices Page Applicability Notice Overview & General SpecificationsComposite Video and Composite Video+Stereo Component and Component+Stereo Y/c+StereoRgbhv and RGBHV+Stereo Product NotesStereo EnclosuresOctaire Control Features Octaire FeaturesRear View Front ViewRear View Components Control Hardware Power Receptacles & SwitchesSerial Number Input & Output Connectors General SpecificationsNetLinx External Control OptionsControl Software BCS Serial Control ProtocolGeneral Hazard Precautions Installation & SetupSite Recommendations Mechanical Rack Loading UnpackingCircuit Overloading Reliable Earthing GroundingRequired items for rack installation Rack Installation & System SetupOptional items for rack installation Installation RecommendationsAttach rack ears To install and set up an Octaire system in a rackCrossover Cable Specifications Additional Installation OptionsLinking Enclosures Link Cable RequirementsLinking Three or More Octaire Enclosures To link two Octaire enclosuresTo link three or more Octaire enclosures Cabling Video Connectors Link Connector LEDsSignal Type Labels on Enclosures Attaching Inputs & OutputsConnecting Video Cables Installing Color Bands for Signal TypesTo connect video inputs and outputs Wiring Sources & Destinations Wiring Stereo Audio Connectors 5-position terminal blockAttaching Wires To attach stereo audio input and output wiresAttaching External Control Connecting an External Serial Controller Connecting Serial ControllersRS-232 Pin Diagram PC Requirements for APControlTo establish external serial control Serial Communication SettingsComplete Power Redundancy Setup Applying Power & StartupPower-Up Sequence To apply power Octaire LED Indicators Indicator Lights at StartupAPWeb Startup Control Panel StartupSerial Control Device Startup NetLinx CompatibleBCS Commands Executing a Test SwitchControl Panel APControl 3.0 or APWebTroubleshooting To execute the test switchTechnical Support AMX Contact InformationTo send the sync signal to a multi-enclosure System Cabling & Setup for Vertical Interval SyncCable Requirement for VIS Cabling a Multi-Enclosure System for VISPrimary Enclosure VIS Toggle SwitchesSecondary Enclosures To set the VIS toggle switchesTCP/IP Port & Indicator LEDs Connecting to the APWeb ServerAPWeb System Setup Service Switch SVCCable Requirements To connect the Octaire system to a LAN or to a PC Fasten the Ethernet link connectorInstallation & Setup Video Signals Signal Types & SpecificationsVideo Types Standard VideoSync Ultra-Wideband VideoStereo Audio Stereo Audio SignalsSignal Types & Specifications Overview Octaire Control Panel OperationControl Keys & Dial Input & Output Keys Take KeyChange Menus & ModesLabeling Input & Output Keys To create and install labels for Input and Output KeysTo execute a test switch Executing SwitchesTo change the virtual matrix routing level Changing Virtual Matrices Routing LevelsTo disconnect inputs and outputs Disconnecting SwitchesTo verify the status of a signal Verifying Signal StatusDefining Global Presets Defining & Executing Global PresetsTo define a global preset Executing Global Presets To execute a global preset Adjusting Output Volume To adjust the volume Adjusting AudioMuting & Un-muting Outputs To mute an output Example of muted output in Output Volume ModeAdjusting Input Gain To un-mute an output while in Mute ModeTo adjust input gain Current gain setting Gain range Locking the Control Panel Locking & UnlockingTo lock the Control Panel To unlock the Control Panel Unlocking the Control PanelSoftware Version Setup OptionsTo check the software version information To change the default virtual matrix routing level Default Virtual MatrixTo enable VIS Vertical Interval Sync VIS ConfigTo set the password Setting the PasswordOctaire Control Panel Operation To enable error code reporting System Error Codes & TroubleshootingTo turn off error code reporting Troubleshooting Octaire Control Panel Operation APWeb Initial Setup by Network Admin Opening the APWeb Server To set up the APWeb serverSystem Requirements Design RequirementLink Function Overview of the Admin HomeUsing a Dhcp IP Address Optional Setting a Static IP AddressTo enter a static IP address To force invocation of a Dhcp IP addressDefault User Name & Password Setting Admin & User Account LoginsTo set the User and Admin Account Logins To execute a test switch with the XBar Executing a Test Switch with the XBarTo disconnect the test switch To send a test BCS command Executing a Test Switch with BCSTo enable or disable product services Enabling/Disabling Product ServicesCustomizing the Site Customizing the Site NameTo customize bootup operations Customizing Bootup OperationsBootup Operations Options Setting the Initial VM to Display Setting the Size of the XBar WindowCustomizing the Control Options Enabling Audio ControlExamples Creating / Editing MacrosTo redefine the contents of an existing macro Defining Routing Levels Manually Configuring VMsTo create a macro To delete a macroTo manually define a routing level VM VM Numbering RulesTo delete an existing routing level VM Resetting the User Name & Password Handling Security IssuesTurning System Security Off To turn system security offOpening a Telnet Session To reset the user name and password to their default valuesTo open a Telnet session Executing & Disconnecting Switches on the XBar Executing & Disconnecting SwitchesNavigating the XBar Controller To execute or disconnect switches Adjusting Audio SettingsTo update system status when using multiple control points Adjusting VolumeAdjusting Input Gain To execute a macro Executing MacrosAPWeb Connection Information Worksheet Login Names RequiredAPWeb Controlling the Octaire Connecting to APWebTo connect to the APWeb server Home Page Links HomeXBar Controller Overview Navigating the XBar Controller To execute or disconnect switches with the XBarAdjusting Volume Updating Status on the XBar Embedding the XBar Applet APWeb Additional Info for Network AdminXBar Applet Tag To add an exception to the proxy setting information Changing the Proxy SettingBe sure Proxy server box is checked Click Advanced Proxy Settings dialog box opens Appendix a Octaire AutoPatch Connector Guide System Component Information Appendix B Programmer’s Interface for System DiagnosticsComponent Settings Verbosity SettingsGeneral Rules for Octaire Diagnostic Commands To access the lowest level of verbosity for all componentsDisplay for i7v1 component 7, verbosity Splash Screen ExamplesAppendix B Programmer’s Interface for System Diagnostics 100 It’s Your World Take Control

Octaire specifications

The AMX Octaire is a remarkable aircraft designed to meet the evolving demands of modern aviation. Renowned for its combination of advanced technology, efficiency, and versatility, the Octaire stands out in the realm of business jets and regional transport.

One of the main features of the AMX Octaire is its sleek aerodynamic design, which not only enhances aesthetics but significantly contributes to fuel efficiency. The aircraft's fuselage is built using advanced composite materials, which reduce weight while maintaining structural integrity. This results in improved performance and operational costs, making the Octaire an attractive option for companies and individuals seeking economical flying solutions.

Powered by two state-of-the-art turbofan engines, the AMX Octaire is capable of reaching an impressive cruising speed while optimizing fuel consumption. These engines are equipped with next-generation noise reduction technologies that conform to stringent environmental regulations, minimizing the aircraft's carbon footprint and contributing to sustainable aviation practices.

The cockpit of the Octaire features cutting-edge avionics, including multifunction displays and an intuitive interface for pilots. This technology enhances situational awareness and simplifies navigation, allowing for a smoother flight experience. The integration of fly-by-wire controls ensures precision handling and improved safety, making the Octaire a reliable choice for both seasoned pilots and newcomers.

Passenger comfort is a top priority in the design of the AMX Octaire. The cabin is spacious and customizable, featuring luxurious seating arrangements, modern entertainment systems, and advanced climate control. High-capacity windows provide ample natural light, creating an inviting atmosphere that enhances the onboard experience. With soundproofing materials expertly incorporated into the design, passengers can enjoy a serene environment during their journeys.

Versatility is another hallmark of the AMX Octaire. It can be adapted for various roles, including business travel, medevac missions, and cargo transport. This flexibility ensures that the Octaire can meet the needs of a diverse clientele, from corporate executives to humanitarian organizations.

In summary, the AMX Octaire is a sophisticated aircraft that embodies efficiency, comfort, and technological advancement. Its design and features position it as a leader in the aviation market, promising to deliver exceptional performance for years to come. Whether used for business or specialized operations, the Octaire is poised to redefine expectations in air travel.