AMX Octaire instruction manual Disconnecting Switches, To disconnect inputs and outputs

Page 54

Octaire Control Panel Operation

Disconnecting Switches

Disconnecting a switch deactivates the connection between an input (source) and one or more output (destination) devices. Disconnecting an input will disconnect all outputs currently receiving the input's signal. An output can only be connected to one input; therefore, disconnecting an output will only disconnect the connection between the output and the input that is routed to it. Inputs and outputs can be selected in the same disconnect command.

You can disconnect inputs or outputs from the Octaire Control Panel using the steps below. If you need to change the routing level, see “Changing Virtual Matrices (Routing Levels)” on page 48.

Note: When you put the panel in Disconnect Mode, available keys will be blue and any unavailable ones will not be illuminated. When you select a blue key, it turns white. You can toggle the keys between the selected (white) and unselected (blue) state before pressing the Take Key. For an example, see FIG. 31 on page 44.

Once the Control Panel is in Disconnect Mode, inputs and outputs can be selected and unselected by pressing the corresponding Input and Output Keys. Pressing the Cancel Key clears an incomplete disconnect command and returns the display to the beginning of the submenu. The disconnect command is not executed until the Take Key is pressed.

While in Disconnect Mode, the Octaire Control Panel will not show current routing for the inputs and outputs that are selected.

Caution: Disconnecting an input disconnects all outputs receiving that source signal even if a specific output(s) is selected at the same time.

The example below disconnects Inputs 1 and 3 and all outputs connected to them as well as Output 9.

To disconnect inputs and outputs:

1.Press the Function Key. The Function menu appears.

2.Locate Disconnect by scrolling with the Control Dial.

3.Press the Select Key.

The system is in Disconnect Mode (all the available Input and Output Keys turn blue).

4.Press Input Keys 1 and 3 and Output Key 9.

The keys turn white indicating that they are selected.

Routing level

Disconnect: VideoAll

Press I/O then Take

5.Press the Take Key.

Inputs 1 and 3 (and all outputs connected to them) and Output 9 are disconnected as soon as the Take Key is pressed, and the keys turn blue.

6.Make additional disconnects.

Or press the Function Key to return to the Function menu.

Octaire Instruction Manual

49

 

 

Image 54
Contents Octaire AMX Limited Warranty and Disclaimer Software License and Warranty Agreement Contents APWeb Controlling the Octaire ESD Warning Important Safety Information & Instructions Information et directives de sécurité importantes Usfcc Notice Copyright NoticeLiability Notice Lithium Batteries NoticeTrademark Notices Page Overview & General Specifications Applicability NoticeComposite Video and Composite Video+Stereo Y/c+Stereo Component and Component+StereoStereo Product NotesRgbhv and RGBHV+Stereo EnclosuresOctaire Features Octaire Control FeaturesFront View Rear ViewRear View Components Power Receptacles & Switches Control HardwareSerial Number General Specifications Input & Output ConnectorsControl Software External Control OptionsNetLinx BCS Serial Control ProtocolInstallation & Setup General Hazard PrecautionsSite Recommendations Circuit Overloading UnpackingMechanical Rack Loading Reliable Earthing GroundingOptional items for rack installation Rack Installation & System SetupRequired items for rack installation Installation RecommendationsTo install and set up an Octaire system in a rack Attach rack earsLinking Enclosures Additional Installation OptionsCrossover Cable Specifications Link Cable RequirementsTo link two Octaire enclosures Linking Three or More Octaire EnclosuresTo link three or more Octaire enclosures Signal Type Labels on Enclosures Link Connector LEDsCabling Video Connectors Attaching Inputs & OutputsInstalling Color Bands for Signal Types Connecting Video CablesTo connect video inputs and outputs Attaching Wires Wiring Stereo Audio Connectors 5-position terminal blockWiring Sources & Destinations To attach stereo audio input and output wiresAttaching External Control RS-232 Pin Diagram Connecting Serial ControllersConnecting an External Serial Controller PC Requirements for APControlSerial Communication Settings To establish external serial controlApplying Power & Startup Complete Power Redundancy SetupPower-Up Sequence To apply power Indicator Lights at Startup Octaire LED IndicatorsSerial Control Device Startup Control Panel StartupAPWeb Startup NetLinx CompatibleControl Panel Executing a Test SwitchBCS Commands APControl 3.0 or APWebTechnical Support To execute the test switchTroubleshooting AMX Contact InformationCable Requirement for VIS Cabling & Setup for Vertical Interval SyncTo send the sync signal to a multi-enclosure System Cabling a Multi-Enclosure System for VISVIS Toggle Switches Primary EnclosureTo set the VIS toggle switches Secondary EnclosuresConnecting to the APWeb Server TCP/IP Port & Indicator LEDsService Switch SVC APWeb System SetupCable Requirements Fasten the Ethernet link connector To connect the Octaire system to a LAN or to a PCInstallation & Setup Video Types Signal Types & SpecificationsVideo Signals Standard VideoUltra-Wideband Video SyncStereo Audio Signals Stereo AudioSignal Types & Specifications Octaire Control Panel Operation OverviewControl Keys & Dial Take Key Input & Output KeysMenus & Modes ChangeTo create and install labels for Input and Output Keys Labeling Input & Output KeysExecuting Switches To execute a test switchChanging Virtual Matrices Routing Levels To change the virtual matrix routing levelDisconnecting Switches To disconnect inputs and outputsVerifying Signal Status To verify the status of a signalDefining & Executing Global Presets Defining Global PresetsTo define a global preset Executing Global Presets To execute a global preset Adjusting Audio Adjusting Output Volume To adjust the volumeExample of muted output in Output Volume Mode Muting & Un-muting Outputs To mute an outputTo un-mute an output while in Mute Mode Adjusting Input GainTo adjust input gain Current gain setting Gain range Locking & Unlocking Locking the Control PanelTo lock the Control Panel Unlocking the Control Panel To unlock the Control PanelSetup Options Software VersionTo check the software version information Default Virtual Matrix To change the default virtual matrix routing levelVertical Interval Sync VIS Config To enable VISSetting the Password To set the passwordOctaire Control Panel Operation System Error Codes & Troubleshooting To enable error code reportingTo turn off error code reporting Troubleshooting Octaire Control Panel Operation APWeb Initial Setup by Network Admin System Requirements To set up the APWeb serverOpening the APWeb Server Design RequirementOverview of the Admin Home Link FunctionTo enter a static IP address Setting a Static IP AddressUsing a Dhcp IP Address Optional To force invocation of a Dhcp IP addressSetting Admin & User Account Logins Default User Name & PasswordTo set the User and Admin Account Logins Executing a Test Switch with the XBar To execute a test switch with the XBarTo disconnect the test switch Executing a Test Switch with BCS To send a test BCS commandCustomizing the Site Enabling/Disabling Product ServicesTo enable or disable product services Customizing the Site NameCustomizing Bootup Operations To customize bootup operationsBootup Operations Options Customizing the Control Options Setting the Size of the XBar WindowSetting the Initial VM to Display Enabling Audio ControlCreating / Editing Macros ExamplesTo create a macro Defining Routing Levels Manually Configuring VMsTo redefine the contents of an existing macro To delete a macroVM Numbering Rules To manually define a routing level VMTo delete an existing routing level VM Turning System Security Off Handling Security IssuesResetting the User Name & Password To turn system security offTo reset the user name and password to their default values Opening a Telnet SessionTo open a Telnet session Executing & Disconnecting Switches Executing & Disconnecting Switches on the XBarNavigating the XBar Controller To update system status when using multiple control points Adjusting Audio SettingsTo execute or disconnect switches Adjusting VolumeAdjusting Input Gain Executing Macros To execute a macroLogin Names Required APWeb Connection Information WorksheetConnecting to APWeb APWeb Controlling the OctaireTo connect to the APWeb server Home Home Page LinksXBar Controller Overview To execute or disconnect switches with the XBar Navigating the XBar ControllerAdjusting Volume Updating Status on the XBar APWeb Additional Info for Network Admin Embedding the XBar AppletXBar Applet Tag Changing the Proxy Setting To add an exception to the proxy setting informationBe sure Proxy server box is checked Click Advanced Proxy Settings dialog box opens Appendix a Octaire AutoPatch Connector Guide Appendix B Programmer’s Interface for System Diagnostics System Component InformationGeneral Rules for Octaire Diagnostic Commands Verbosity SettingsComponent Settings To access the lowest level of verbosity for all componentsSplash Screen Examples Display for i7v1 component 7, verbosityAppendix B Programmer’s Interface for System Diagnostics 100 It’s Your World Take Control

Octaire specifications

The AMX Octaire is a remarkable aircraft designed to meet the evolving demands of modern aviation. Renowned for its combination of advanced technology, efficiency, and versatility, the Octaire stands out in the realm of business jets and regional transport.

One of the main features of the AMX Octaire is its sleek aerodynamic design, which not only enhances aesthetics but significantly contributes to fuel efficiency. The aircraft's fuselage is built using advanced composite materials, which reduce weight while maintaining structural integrity. This results in improved performance and operational costs, making the Octaire an attractive option for companies and individuals seeking economical flying solutions.

Powered by two state-of-the-art turbofan engines, the AMX Octaire is capable of reaching an impressive cruising speed while optimizing fuel consumption. These engines are equipped with next-generation noise reduction technologies that conform to stringent environmental regulations, minimizing the aircraft's carbon footprint and contributing to sustainable aviation practices.

The cockpit of the Octaire features cutting-edge avionics, including multifunction displays and an intuitive interface for pilots. This technology enhances situational awareness and simplifies navigation, allowing for a smoother flight experience. The integration of fly-by-wire controls ensures precision handling and improved safety, making the Octaire a reliable choice for both seasoned pilots and newcomers.

Passenger comfort is a top priority in the design of the AMX Octaire. The cabin is spacious and customizable, featuring luxurious seating arrangements, modern entertainment systems, and advanced climate control. High-capacity windows provide ample natural light, creating an inviting atmosphere that enhances the onboard experience. With soundproofing materials expertly incorporated into the design, passengers can enjoy a serene environment during their journeys.

Versatility is another hallmark of the AMX Octaire. It can be adapted for various roles, including business travel, medevac missions, and cargo transport. This flexibility ensures that the Octaire can meet the needs of a diverse clientele, from corporate executives to humanitarian organizations.

In summary, the AMX Octaire is a sophisticated aircraft that embodies efficiency, comfort, and technological advancement. Its design and features position it as a leader in the aviation market, promising to deliver exceptional performance for years to come. Whether used for business or specialized operations, the Octaire is poised to redefine expectations in air travel.