Alcatel Carrier Internetworking Solutions 4324 GE Uplink Ports, Physical Description and LEDs

Page 36

OmniAccess 4324: Installation Guide

For cables that run through plenums or air-handling spaces as described in NEC (2002) Article 300.22(C), the cable should be suitable under NEC Article

800.50and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP.

Be sure to install cables in accordance with all applicable local regulations and practices.

GE Uplink Ports

The switch has two Gigabit Ethernet (GE) uplink ports. These ports provide high-bandwidth 10/100/1000 Mbps Gigabit Ethernet uplinks between the Alcatel Wireless LAN Switch and the wired LAN. The port automatically senses and negotiates speed, duplex, and MDI/MDX settings.

Physical Description and LEDs

LNK/

ACT

LNK/

ACT

24

25

FIGURE B-3GE Uplink Ports

Each GE port socket accepts a variety of Gigabit Interface Converters (GBICs) for versatility in selecting optical and electrical interfaces.

Each GE port has its own LNK/ACT LED, located to the right of the port. During operation, these LEDs provide the following status information:

	TABLE B-5GE LNK/ACT LED

Status	Description

Off	No Ethernet link on the port.
Green	An Ethernet link has been established on the port, but no
	data is currently being transmitted or received.
Flashing	The port is transmitting or receiving data. The flashing rate is
Green	proportional to your network activity.

22

Part 031640-00

May 2005

Image 36

Contents

OmniAccess 4324TM Copyright FCC Class a Industry Canada Class aVcci Class a CE Class a Safety EU Class aContents Serial & Power Over Ethernet Physical Description & LEDs Pin Outs Cables GE Uplink PortsPreface Overview of this ManualRelated Documents Text ConventionsContacting Alcatel OmniAccess 4324 Installation Guide Alcatel Wireless LAN Solution To the Network ManagerPhysical installation of the Alcatel Wireless LAN Switch Initial configuration of the Alcatel Wireless LAN SwitchPlanning the location of access points and air monitors Deployment SummaryPhysical installation of the Alcatel Wireless Access Points Advanced configuration of the Alcatel Wireless LAN SwitchMonitoring and maintenance OmniAccess 4324 Installation Guide Xiv Features System OverviewSystem Indicator LEDs PowerPhysical Description StatusGE uplink ports Fans/heat exhaust on sideOmniAccess 4324 Installation Guide Installing the Chassis Pre-Installation ChecklistPrecautions Requirements Rack Mounting KitSelecting a Location Cool, non-condensing ventilationMounting the Chassis 2Attaching the Rack Mounting BracketsAttach the Alcatel Wireless LAN Switch to the rack 3Mounting the Alcatel Wireless LAN SwitchAdhere to clearance requirements 4Keep Clear ZonesConnecting Power Verify you understand the procedure and all precautionsAttach the power cord to a proper electrical outlet Verifying the Installation Check for the proper power indicatorsCheck for the appropriate operation indicators Check the fans to verify they are workingOnce the system has passed the initial power-up test Power Management Component Name Power Number Rating Units SubtotalTotal POE power required in Watts OmniAccess 4324 Installation Guide Ports Gigabit Ethernet GE portsSerial & Power Over Ethernet OmniAccess 4324 FE Network PortsFE Network Ports Physical Description & LEDsFE Network Ports Status DescriptionAccess Point Status LEDs Pin OutsCables AP Make and ModelSerial Alcatel Spoe Adapter GE Uplink Ports Physical Description and LEDsApproved GBICs Gbic Type Vendor Module IDGbic Type Characteristics CablesSerial Console Port Port & Adapter Pin OutsCommunications Settings Baud Rate Data Bits Parity Stop Bits Flow ControlSpecifications SpecificationPhysical EnvironmentCertifications Page OmniAccess 4324 Installation Guide