D-Link DES-3208 manual Limited Warranty

Page 4

Limited Warranty

Hardware:

D-Link warrants its hardware products to be free from defects in workmanship and materials, under normal use and service, for the following lengths of time from the date of purchase from D-Link or its Authorized Reseller:

Product Type

Warranty Period

Network adapters

Lifetime

Unmanaged and managed hubs (10Mbps)

Lifetime *

Unmanaged and managed hubs (100Mbps)

One year

Managed Switches

Three years *

Unmanaged switches

Lifetime *

Repeaters, MAUs , transceivers, media converters

One year

Concentrators

One year

Internetworking products

One year

* Power supply and fans in these devices

One year

Other hardware products

One year

Spare parts and spare kits

90 days

If a product does not operate as warranted during the applicable warranty period, D-Link shall, at its option and expense, (1) repair the defective product or part, (2) deliver to Customer an equivalent product or part to replace the defective item. All products that are replaced will become the property of D-Link. Replacement products may be new or reconditioned. Any replaced or repaired product or part has a ninety (90) day warranty or the remainder of the initial warranty period, whichever is longer.

D-Link shall not be responsible for any software, firmware, information, or memory data of Customer contained in, stored on, or integrated with any products returned to D-Link pursuant to any warranty.

All products with lifetime warranty have a standard five-year warranty. To qualify for lifetime warranty, the enclosed Product Registration Card must be completed and returned to D-Link within ninety (90) days of purchase.

Warranty service may be obtained by contacting a D-Link office within the applicable warranty period for a Return Material Authorization (RMA) number. If a Registration Card has not been previously sent, proof of purchase, such as a copy of the dated purchase invoice, must be provided. Once an RMA number is issued, the defective product must be shipped back to D-Link prepaid, insured and wrapped in the original or similar shipping package to ensure that it will not be damaged during shipment. When returning the defective product to D-Link for service, the RMA number must be marked on the outside of the shipping package. Any product returned without an RMA number shall be rejected and sent back to the Customer, and D-Link reserves the right to have Customer bear the cost of sending back such products. A service charge may or may not be levied to Customer by D-Link. To find out if a service charge is levied or not, and the charged amount, read the RMA that is returned to Customer, or ask the D-Link office when an RMA is requested.

Image 4
Contents DES-3208 10/100 Fast Ethernet Switch User’s Guide Wichtige Sicherheitshinweise Warranties Exclusive Limited Warranty Software Trademarks Page Page Table of Contents Switch Management Switch Monitoring Page Terms About this GuideOverview of this User’s Guide Appendix C, MII Port Specifications Introduction Fast Ethernet TechnologySwitching Technology Performance features FeaturesPorts Management Unpacking Setup UnpackingSetup Desktop or Shelf InstallationRack Installation 100 Fast Ethernet Switch installed on a Desktop or ShelfPower on Power Failure Identifying External Components Front PanelRear Panel Rear panel view of the DES-320810/100 Fast Ethernet Switch User’s Guide LED Indicators DES-3208 Switch LED indicators10/100 Fast Ethernet Switch User’s Guide Connecting Switch PC to SwitchHub to Switch DES-3208 Switch connected to a 10BASE-T or 100Base-TX Hub10Base-T Hub Hub without Uplink MDI-II port100Base-TX Hub Using straight cable Switch to Switch other devicesUsing crossover cable Using straight cable Switch Management Local Console ManagamentConsole port RS-232 DCE IP Addresses and Snmp Community NamesTraps MIBs Packet Forwarding Aging Time Spanning Tree AlgorithmAutomatic topology re-configuration STA Operation LevelsUser-Changeable Parameters On the Port Level10/100 Fast Ethernet Switch User’s Guide Illustration of STA Before Applying the STA Rules User-selective STA parameters Using the Console Interface Connecting to the SwitchConsole Usage Conventions First Time Connecting To The Switch Super and General User Privileges Steps to create a Super User or General UserMain Menu for General User Super User and General User Privileges Login on the Switch Console by Registered Users Changing Your Password Choose Change PasswordAdding and Deleting Users Adding a New UserDeleting a User Setting up the Switch TCP/IP SettingsUsing the Console Interface Out-of-band management and console settings System Restart SettingSoftware Updates 11. Out-of-Band/Console Setting MenuSystem Configuration Menu 12. Software Update MenuSnmp Management Settings Snmp Trap Manager Configuration14. Snmp Trap Manager Configuration Menu Snmp Manager Configuration Snmp Security Community NamesPort Configuration 16. Port Configuration MenuSwitch Monitoring Displaying Port Statistics17. Statistics Counters Spanning Tree Algorithm Parameters Forwarding Table Custom Filtering Table 18. STA, Forwarding Table19. Custom Filtering Table Using the Console Interface Protocol Parameters Stap Port Parameters 21. Protocol ParametersResetting the Switch 22. Stap Port ParametersSystem Reset Factory Reset24. Factory Reset Technical Specifications GeneralPhysical and Environmental Performance Specification RJ-45 PINRJ-45 Connector pin assignment MII Connector Specifications Figure C-1. The Standard MII connectorMII Connector Pin Assignment Table C-1. The MII standard pin assignment BOOTP&TFTP, 48 Tftp only IndexIndex MDI-II Index Page Offices Registration Card