Altinex MX2456RM manual RS-232 Control, PIN No PIN Designation

Page 9

SWITCHERS

6.If necessary, select the SYNC DELAY UP or DOWN button. To activate and set the SYNC DELAY mode to memory, press and hold the UP or DOWN button. LED’s that represent the selected time should light.

7.To activate the AUTO SWITCH mode, press the AUTO SWITCH button. The LED that represents the AUTO SWITCH mode should light. If the AUTO ROTATE mode was selected previously, it will cancel. Audio inputs will follow video inputs if the AUDIO BREAK AWAY mode was not selected previously.

8.The AUDIO VOLUME mode will control the audio stereo volume when the VOLUME UP or DOWN button is pressed and released. The AUDIO VOLUME UP or DOWN button is between a maximum volume of +6dB and a minimum volume of –6dB. From the minimum to maximum volume, there are fifteen points. Each point represents 0.8dB. After selecting the volume, press and hold the UP and DOWN buttons simultaneously.

9.To turn OFF the beeping sound, press and hold the BEEP ON/OFF button. The LED that represents this button should light. To activate sound, press and hold the BEEP ON/OFF button again.

10.To return the switcher to factory preset, press the RESET button. After a brief delay, all LED’s should blink ON and OFF. A beeping sound will be heard several times indicating that the switcher has been reset.

7.2 RS-232 CONTROL

The MX2456RM Switcher offers remote control capabilities through RS-232; the primary communication standard used by control systems and computers.

In fact, the MX2456RM offers more features using RS-232 than are currently available from the front panel of the unit.

The MX2456RM offers a terminal block using solder-free, screw-down contacts, making it extremely easy to connect the switcher to a control system or a computer in the field.

Figure 1. RS-232 Terminal Block

PIN No.

PIN Designation

1

+5V (not needed for

 

RS-232 connection)

2

GND (Ground)

3

RCV (Receive)

4

XMT (Transmit)

Table 4. PIN Designations

The terminal block is labeled with the appropriate contact designations: Transmit (XMT), Receive (RCV), and Ground (GND). Always remember that the Transmit pin from the control system or computer must be connected to the Receive pin on the switcher control port; do not connect Transmit to Transmit or Receive to Receive.

Note: the contact labeled +5V is not used for RS-232 connections. This contact is used to provide DC voltage to other equipment installed within close proximity of the MX2456RM.

Typically, a control system or computer will offer RS-232 connections on a 9-pin D connector.

The following are typical cable pin-out designations for RS-232 connections on a 9-pin D connector. Always verify that the pin-outs for your system are correct to ensure the proper wiring.

IBM PIN No.

MX2456RM

 

Contact

3

RX

2

TX

7

GND

Connection of IBM-PC 25-pin D to the MX2456RM Terminal Block

8

Page 8 Page 10
Image 9
Page 8 Page 10
Contents MX2456RM Table of Contents Precautions / Safety Warnings About Your MX2456RM Technical SpecificationAudio MX2456RMPage Audio Break Away Mode Video Select ModeEqualization Mode Auto Switch ModePage Installing Your MX2456RM OperationControl Panel PIN No PIN Designation RS-232 Control# SW n1 n2 n3 n4 n5 n6 Video Switch Input Programming Commands# SW n1 n2 n3 n4 n5 n6 Audio Switch Input 1 RS-232 Protocol#RO Operation Reset #RF Factory Reset#CSDn Sync Delay # SA n Audio Breakaway10. #CA n1 n2 Audio Gain Control Save Settings OASn Auto Switch11. #CA n1 n2 Video Equalization Save Settings #Bn Beep ON/OFFRack Mounting Accessories AccessoriesFrequently Asked Questions Troubleshooting GuideAltinex Policy

MX2456RM specifications

The Altinex MX2456RM is a highly regarded multimedia matrix switcher specifically designed to meet the demands of modern AV systems. This versatile device offers seamless switching capabilities for various audio and video signals, making it an ideal solution for educational institutions, corporate environments, and event venues.

One of the standout features of the MX2456RM is its capacity to accommodate multiple input and output configurations. With support for up to 24 inputs and 56 outputs, it provides flexibility for complex setups, allowing users to route signals from various sources to desired destinations. This capability is particularly useful in environments where multiple presentations or media streams occur simultaneously.

The unit supports a wide range of video resolutions, ensuring compatibility with various devices. It handles signals up to 4K resolution at 60 Hz, which is crucial for maintaining high-quality visuals in today’s high-definition content landscape. Additionally, the MX2456RM supports multiple video formats, including HDMI and SDI, providing versatility for different AV equipment.

Another noteworthy aspect of the MX2456RM is its sophisticated control options. Users can manage the matrix switcher through a user-friendly web interface, enabling easy configuration and operation from any web-enabled device. This simplifies the control process significantly, making it accessible to users with varying levels of technical expertise.

The MX2456RM also features advanced audio processing capabilities. With support for audio embedding and de-embedding, users can manage audio signals seamlessly alongside video, providing a comprehensive AV experience. This functionality is essential for ensuring synchronized audio-video output, especially during presentations or live events.

Reliability is another critical characteristic of the MX2456RM. Altinex has designed this unit with robust hardware and features such as hot-swappable modules, ensuring minimal downtime during operation. This reliability is especially important in professional environments where AV performance is critical.

In summary, the Altinex MX2456RM is an exceptional multimedia matrix switcher that combines extensive input-output options, high-resolution support, user-friendly control, and reliable performance. It is an ideal choice for organizations looking to enhance their AV capabilities and streamline their media management processes. Whether it’s for educational use, corporate presentations, or live events, the MX2456RM stands out as a powerful tool for professionals in the AV industry.
Top Page Image Contents