Altinex MX2456RM manual Precautions / Safety Warnings

Page 3

SWITCHERS

PRECAUTIONS / SAFETY WARNINGS

1

Please read this manual carefully before using your MX2456RM Switcher. Keep this manual handy for future reference. These safety instructions are to ensure the long life of your MX2456RM and to prevent fire and shock hazard. Please read them carefully and heed all warnings.

1.1 GENERAL

Unauthorized personnel shall not open the unit since there are high-voltage components inside.

Qualified ALTINEX service personnel, or their authorized representatives must perform all service.

1.2SAFETY GUIDELINES FOR THE RACK- MOUNTING OF THE MX2456RM

Maximum operating ambient temperature is 35 (degrees C).

Never restrict the air flow through the devices’ fan or vents.

When installing equipment into a rack, distribute the units evenly. Otherwise, hazardous conditions may be created by an uneven weight distribution.

Connect the unit to a properly rated supply circuit.

Reliable Earthing (Grounding) of Rack-Mounted Equipment should be maintained.

1.3 INSTALLATION

For best results, place the MX2456RM Switcher on a flat, level surface in a dry area away from dust and moisture.

To prevent fire or shock, do not expose this unit to rain or moisture. Do not place the MX2456RM Switcher in direct sunlight, near heaters or heat radiating appliances, or near any liquid. Exposure to direct sunlight, smoke, or steam can harm internal components.

Handle the MX2456RM Switcher carefully. Dropping or jarring can damage internal components.

Do not place heavy objects on top of the MX2456RM. If the MX2456RM is to be mounted to a table or wall, use only ALTINEX- made mounting accessories, such as rack mount shelf DA1298RM or rack mount ears DA1292FC and cables for optimum setup.

To turn off the main power, be sure to remove the cord from the power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

Do not pull the power cord or any cable that is attached to the MX2456RM Switcher.

If the MX2456RM Switcher is not used for an extended period, disconnect the power cord from the power outlet.

1.4 CLEANING

Unplug the MX2456RM power cord before cleaning. Clean surfaces with a dry cloth. Never use strong detergents or solvents, such as alcohol or thinner. Do not use a wet cloth or water to clean the unit.

1.5 FCC / CE NOTICE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

2

Image 3
Contents MX2456RM Table of Contents Precautions / Safety Warnings MX2456RM Technical SpecificationAbout Your MX2456RM AudioPage Auto Switch Mode Video Select ModeAudio Break Away Mode Equalization ModePage Installing Your MX2456RM OperationControl Panel PIN No PIN Designation RS-232 Control1 RS-232 Protocol Programming Commands# SW n1 n2 n3 n4 n5 n6 Video Switch Input # SW n1 n2 n3 n4 n5 n6 Audio Switch Input# SA n Audio Breakaway #RF Factory Reset#RO Operation Reset #CSDn Sync Delay#Bn Beep ON/OFF OASn Auto Switch10. #CA n1 n2 Audio Gain Control Save Settings 11. #CA n1 n2 Video Equalization Save SettingsRack Mounting Accessories AccessoriesFrequently Asked Questions Troubleshooting GuideAltinex Policy

MX2456RM specifications

The Altinex MX2456RM is a highly regarded multimedia matrix switcher specifically designed to meet the demands of modern AV systems. This versatile device offers seamless switching capabilities for various audio and video signals, making it an ideal solution for educational institutions, corporate environments, and event venues.

One of the standout features of the MX2456RM is its capacity to accommodate multiple input and output configurations. With support for up to 24 inputs and 56 outputs, it provides flexibility for complex setups, allowing users to route signals from various sources to desired destinations. This capability is particularly useful in environments where multiple presentations or media streams occur simultaneously.

The unit supports a wide range of video resolutions, ensuring compatibility with various devices. It handles signals up to 4K resolution at 60 Hz, which is crucial for maintaining high-quality visuals in today’s high-definition content landscape. Additionally, the MX2456RM supports multiple video formats, including HDMI and SDI, providing versatility for different AV equipment.

Another noteworthy aspect of the MX2456RM is its sophisticated control options. Users can manage the matrix switcher through a user-friendly web interface, enabling easy configuration and operation from any web-enabled device. This simplifies the control process significantly, making it accessible to users with varying levels of technical expertise.

The MX2456RM also features advanced audio processing capabilities. With support for audio embedding and de-embedding, users can manage audio signals seamlessly alongside video, providing a comprehensive AV experience. This functionality is essential for ensuring synchronized audio-video output, especially during presentations or live events.

Reliability is another critical characteristic of the MX2456RM. Altinex has designed this unit with robust hardware and features such as hot-swappable modules, ensuring minimal downtime during operation. This reliability is especially important in professional environments where AV performance is critical.

In summary, the Altinex MX2456RM is an exceptional multimedia matrix switcher that combines extensive input-output options, high-resolution support, user-friendly control, and reliable performance. It is an ideal choice for organizations looking to enhance their AV capabilities and streamline their media management processes. Whether it’s for educational use, corporate presentations, or live events, the MX2456RM stands out as a powerful tool for professionals in the AV industry.