Altinex MX2436RM Precautions / Safety Warnings, General, Installation, Cleaning, Fcc / Ce Notice

Page 3
PRECAUTIONS / SAFETY WARNINGS

SWITCHERS

PRECAUTIONS / SAFETY WARNINGS

1

Please read this manual carefully before using your MX2436RM Switcher. Keep this manual handy for future reference. These safety instructions are to ensure the long life of your MX2436RM and to prevent fire and shock hazard. Please read them carefully and heed all warnings.

1.1 GENERAL

Unauthorized personnel shall not open the unit since there are high-voltage components inside.

Qualified ALTINEX service personnel, or their authorized representatives must perform all service.

1.2SAFETY GUIDELINES FOR THE RACK- MOUNTING OF THE MX2436RM

Maximum operating ambient temperature is 35 (degrees C).

Never restrict the air flow through the devices’ fan or vents.

When installing equipment into a rack, distribute the units evenly. Otherwise, hazardous conditions may be created by an uneven weight distribution.

Connect the unit to a properly rated supply circuit.

Reliable Earthing (Grounding) of Rack-Mounted Equipment should be maintained.

1.3 INSTALLATION

For best results, place the MX2436RM Switcher on a flat, level surface in a dry area away from dust and moisture.

To prevent fire or shock, do not expose this unit to rain or moisture. Do not place the MX2436RM Switcher in direct sunlight, near heaters or heat radiating appliances, or near any liquid. Exposure to direct sunlight, smoke, or steam can harm internal components.

Handle the MX2436RM Switcher carefully. Dropping or jarring can damage internal components.

Do not place heavy objects on top of the MX2436RM. If the MX2436RM is to be mounted to a table or wall, use only ALTINEX- made mounting accessories, such as rack mount shelf DA1298RM or rack mount ears DA1292FC and cables for optimum setup.

To turn off the main power, be sure to remove the cord from the power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

Do not pull the power cord or any cable that is attached to the MX2436RM Switcher.

If the MX2436RM Switcher is not used for an extended period, disconnect the power cord from the power outlet.

1.4 CLEANING

Unplug the MX2436RM power cord before cleaning. Clean surfaces with a dry cloth. Never use strong detergents or solvents, such as alcohol or thinner. Do not use a wet cloth or water to clean the unit.

1.5 FCC / CE NOTICE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

2

Image 3
Contents SWITCHERS 6-IN, 1-OUT COMPOSITE VIDEO AUDIO SWITCHER USER’S GUIDEMX2436RM Page TABLE OF CONTENTS1.4 CLEANING PRECAUTIONS / SAFETY WARNINGS1.2 SAFETY GUIDELINES FOR THE RACK- MOUNTING OF THE MX2436RM 1.3 INSTALLATIONAudio TECHNICAL SPECIFICATIONABOUT YOUR MX2436RM MX2436RMDESCRIPTION OF MX2436RM 4.9. RESET MODE 4.4. AUTO SWITCH MODE4.6 AUDIO VOLUME CONTROL 4.7. VERTICAL INTERVAL SWITCHING MODEAPPLICATION DIAGRAM INSTALLING YOUR MX2436RM OPERATION7.1 CONTROL PANEL 7.2 RS-232 CONTROL OF THE SWITCHER PIN NoPIN Designation 1. # SW n1 n2 n3 n4 n5 n6 - Video Switch Input 1. Square brackets ““ & “” are part of the command2. Use uppercase letters for all commands 7.2.2 PROGRAMMING COMMANDS5. # SA n - Audio Breakaway 2. # SW n1 n2 n3 n4 n5 n6 - Audio Switch Input3. #RF - Factory Reset 4. #RO - Operation Reset8. 0I# - Change Identification Number 9. #CA n1 n2 - Audio Gain Control Save Settings10. #CA n1 n2 - Video Equalization Save Settings 6. #Bn - Beep ON/OFF4. #RO - Operation Reset 5. # SA n - Audio Breakaway ACCESSORIES7.2.3 SUMMARY OF COMMANDS 2. # SW n1 n2 n3 n4 n5 n6 - Audio Switch Input 3. #RF - Factory ResetTROUBLESHOOTING GUIDE FREQUENTLY ASKED QUESTIONS11.3 CONTACT INFORMATION 11.1 LIMITED WARRANTYALTINEX POLICY 11.2 RETURN POLICY