Altinex MX2414RM manual MASTER-SLAVE Configuration, MX2416RM 9-pin D

Page 10

SWITCHERS

[OUTmm]

This command sets the switcher to respond to specific output only. The default setting is output 1.

[SETxnnmm]

 

x -

select input number

nn -

Minimum input number

mm- Maximum input number

This command is designed to allow the MX2416RM to program each input to respond to a selected range of input commands.

For example, if command [SET10104] is issued, then the following commands will select only Input

1:[I01O01], [I02O01], [I03O01], and [I04O01]. In other words a range of I/O commands can address the same input. The default settings for each of the inputs are as follows Input 10101, Input 20202, Input 30303, Input 40404, Input 50505, and Input 60606.

7.3MASTER-SLAVE CONFIGURATION

These feedback codes allow multiple MX2416RM Switchers to be connected in a Master-Slave configuration, if desired.

When the control ports of two units are connected as shown below, the slave unit duplicates the actions of the master unit. The same unit can still be controlled from its front panel or through another RS-232 control.

MX2416RM 9-pin D

MX2416RM 9-pin D

Master PIN No.

Slave PIN No.

2

3

5

5

Master-Slave Control Port Connection

A Master-Slave configuration can be achieved also by Analog Switch Voltage using pin#9 and pin#7.

MX2416RM 9-pin D

MX2416RM 9-pin D

Master PIN No.

Slave PIN No.

9

7

5

5

Master-Slave Analog Switch Voltage Connection

With this configuration the Master unit has ultimate control over slave unit.

7.4CONTACT CLOSURE (ONE WIRE ANALOG) CONTROL

The one wire control is an alternative to a multi- wire contact closure control. This control pin allows you to select different channels based on the DC voltage level on the pin 7 of the 9 pin D connector. Internally pin 7 is pooled up to 5 volts by 10k resistor. Thus, by selecting proper resistor values connected to ground any channel can be selected. Although the channel selection by the relay contact is latching and will maintain the last relay selected channel, it is recommended that momentary contact closures are not used. A typical resistor values and wires connections are shown below.

In some cases it may be preferable to use a seven conductor wire to control the switcher with contact closures. The RC5204CC adapter is available to

9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents MX2416RM/MX2414RM Table of Contents IntroductionPrecautions / Safety Warnings About Your Switcher Technical Specifications MX2416RM/MX2414RM GeneralDescription of MX2416RM Select Input Auto Switch Mode ButtonReset Button Stand by / ALL Channels OFF ButtonPower Supply Application DiagramPower UP Default SET BI-DIRECTIONAL SwitchingOperation Installing Your SwitcherCONGRATULATIONS! YOU are Done RS-232 Protocol VernContact Closure ONE Wire Analog Control MASTER-SLAVE ConfigurationMaster-Slave Analog Switch Voltage Connection MX2416RM 9-pin DManual Loop Control Loop Control with RS-232 CommandMX2416RM Loop Accessories Troubleshooting Guide Frequently Asked QuestionsMX2416RM Return Policy Limited WarrantyAltinex Policy Contact Information

MX2414RM, MX2416RM specifications

The Altinex MX2416RM and MX2414RM are advanced, multi-input, and multi-output audio-video switchers designed to meet the demands of modern AV environments. These units stand out for their reliability, versatility, and performance, making them suitable for various applications such as conference rooms, auditoriums, and educational institutions.

One of the standout features of the MX2416RM is its ability to handle up to 16 input sources and distribute to multiple outputs seamlessly. This capability allows for great flexibility in selecting and switching between different video and audio sources, enhancing the overall AV experience. Similarly, the MX2414RM, designed to switch up to 14 inputs, maintains high-quality output standards, making it ideal for setups with slightly lesser requirements.

Both models incorporate advanced signal routing technology, ensuring that video signals remain crisp and clear without degradation. They support a wide range of resolutions, including HD, 4K, and other high-definition formats, catering to the needs of modern displays and projectors. With support for various input and output formats, including HDMI, VGA, and component video, these switchers can handle multiple types of AV gear seamlessly.

Another significant characteristic of the MX2416RM and MX2414RM is their user-friendly interface. Both units feature intuitive control options, including front-panel buttons, remote control functionality, and integration capabilities with popular control systems. This ease of use makes it simple for operators to manage input and output selections, making them ideal for any user, regardless of technical skill.

The robust design of these switchers also contributes to their reliability. Built with high-quality components, they are designed to withstand the rigors of daily use in busy environments. The redundant power supply option in these units ensures uninterrupted operation, which is crucial in critical AV settings.

Additionally, both models come equipped with ample diagnostic features, including LED indicators for quick status checks and troubleshooting. The integration of advanced technologies, such as automatic input scaling and seamless switching, enhances the user experience further, providing a smooth transition between sources without any noticeable delay.

In summary, the Altinex MX2416RM and MX2414RM are powerful solutions for anyone looking to manage multiple AV inputs and outputs efficiently. With their extensive features, superior audio and video quality, and user-friendly interfaces, they represent a significant advancement in AV switcher technology, making them invaluable tools in any professional AV setup.
Top Page Image Contents