Allied Telesis AT-8000S manual Managing System Files

Page 141

Allied Telesis AT-8000S Switch

Web Browser Interface User’s Guide

Section 13. Managing System Files

The configuration file structure involves the following configuration files:

•Startup Configuration File — Contains the commands required to reconfigure the device to the same settings as when the device is powered down or rebooted. The Startup file is created by copying the configuration commands from the Running Configuration file or the Backup Configuration file.

•Running Configuration File — Contains all configuration file commands, as well as all commands entered during the current session. After the device is powered down or rebooted, all commands stored in the Running Configuration file are lost. During the startup process, all commands in the Startup file are copied to the Running Configuration File and applied to the device. During the session, all new commands entered are added to the commands existing in the Running Configuration file. Commands are not overwritten. To update the Startup file, before powering down the device, the Running Configuration file must be copied to the Startup Configuration file. The next time the device is restarted, the commands are copied back into the Running Configuration file from the Startup Configuration file.

•Backup Configuration Files — Contains a backup copy of the device configuration. Up to five backup configuration files can be saved on the device, with user configured names. These files are generated when the user copies the Running Configuration file or the Startup Configuration file to a user-named file. The contents of the backup configuration files can be copied to either the Running Configuration or the Startup Configuration files.

•Image Files — Software upgrades are used when a new version file is downloaded. The file is checked for the right format, and that it is complete. After a successful download, the new version is marked, and is used after the device is reset.

There are two types of files, firmware files and configuration files. The firmware files manage the device, while the configuration files configure the device for transmissions. Configuration files can be uploaded and downloaded to the device.

System files are uploaded or downloaded using the Trivial File Transfer Protocol (TFTP). TFTP utilizes the User Data Protocol (UDP) without security features.

Note

Only one type of download or upload can be performed at any one time. During upload or download, no user configuration can be performed.

File maintenance includes configuration file management and device access. This section describes the following topics:

•Restoring the Default Configuration

•Defining TFTP File Uploads and Downloads

Page 140

Page 140 Page 142
Image 141
Page 140 Page 142
Contents AT-8000S Series Layer Ethernet SwitchTable of Contents Configuring Ports Configuring Power Over Ethernet 126 176 Table of Contents Web Browser Interface User’s Guide PrefaceWeb Browser Interface User’s Guide Overview Intended AudienceWeb Browser Interface User’s Guide Overview Document Conventions Contacting Allied TelesisOnline Support Contacting Allied Telesis Click Login. The Embedded Web System Home Page opens Getting StartedStarting the Application Starting the Application Click Configuration. The System General Page opensUsing the Web Browser Interface Click Layer 1 Port Settings. The Port Settings Page opensViewing the Device Representation User Interface Components Using the Web Browser InterfaceInterface Components Component DescriptionUsing the Management Buttons Configuration Management ButtonsButton Button Name Description Add Local User Adding, Modifying and Deleting InformationLogging Out Saving ConfigurationsResetting the Device Resetting the DeviceClick System General. The System General Page opens Defining System InformationDefining System Information Configuring System Time Configuring System Time Click System System Time. The System Time Page opens Setting the System ClockConfiguring Sntp Configuring SntpPolling for Unicast Time Information Polling for Anycast Time InformationDefine the Server IP Address and the Poll Interval fields Configuring Daylight Saving TimeConfiguring Daylight Saving Time Configuring Device Security Configuring Management Security Configuring Management SecurityHttp Defining Access ProfilesClick Add. The Add Access Profile Page opens Add Access ProfileAllied Telesis AT-8000S Switch Profile Rules Defining Profile RulesClick Add. The Add Profile Rule Page opens Add Profile RuleClick Modify. The Profiles Rules Configuration Page opens Profiles Rules ConfigurationAuthentication Profiles Defining Authentication ProfilesClick Add. The Add Authentication Profile Page opens Enter the Profile Name Add Authentication ProfileAuthentication Mapping Mapping Authentication ProfilesConfiguring Server Based Authentication Configuring TACACS+Define the Console, Telnet, and Secure Telnet SSH fields TACACS+ Configuration Add TACACS+ Radius Configuration Configuring RadiusAdd Radius Click Mgmt. Security Local Users. The Local Users Page opens Configuring Local UsersClick Create. The Add Local User Page opens Click Modify. The Local User Configuration Page opensConfiguring Network Security Configuring Network SecurityManaging Port Security Network Security OverviewPort Security Click Modify. The Port Security Configuration Page opensPort Security Configuration 802.1x Port Access Defining 802.1x Port AccessClick Enable Port Access Select the Authentication MethodClick Settings. The Port Authentication Settings Page opens Configuring Device Security Enabling Storm Control Click Modify. The Storm Control Configuration Page opensStorm Control Configuration Configuring Ports Defining Port Settings Defining Port SettingsClick Modify. The Modify Port Settings Page opens Modify Port Settings Configuring Ports Allied Telesis AT-8000S Switch Configuring Port Mirroring Configuring Port MirroringClick Layer 1 Port Mirroring. The Port Mirroring Page opens Click Modify. The Modify Mirror Page opens Click Enable MirrorTo modify or delete a port mirror Aggregating Ports Defining Trunk Settings Click Layer 1 Port Trunking. The Trunk Settings Page opensAggregating Ports Click Modify. The Trunk Settings Page opens Trunk Configuration SettingsConfiguring Ports Allied Telesis AT-8000S Switch Port Trunking Defining Port TrunkingModify Trunk Click Modify. the Modify Lacp Settings Page opens Configuring LacpConfiguring Interfaces Defining MAC Addresses Defining MAC AddressesClick Layer 2 MAC Address. The MAC Address Page opens Click Add. The Add MAC Address Page opens Add MAC AddressClick Close. The View MAC Address Table Page is displayed View MAC Address TableConfiguring VLANs Defining Vlan Properties Configuring VLANsAllied Telesis AT-8000S Switch Click Layer 2 Vlan Interface. The Vlan Interface Page opens Defining Vlan Interface SettingsClick Modify. The Modify Interface Configuration Page opens Modify Interface ConfigurationDefining Gvrp Configuring GvrpClick Modify. The Gvrp Port Configuration Page opens Select Enable GvrpDefine the Gvrp State and Gvrp Registration fields Enabling/Disabling Gvrp on a PortConfiguring System Logs Defining Log Settings Defining Log SettingsSystem Log Severity Levels Description Message Event Log Clearing Event Logs Configuring Log ServersClearing Event Logs Click Create. The Add Syslog Server Page opensClick Modify. The Modify Event Log Output Page opens Setting System Log DisplayViewing Flash Logs Viewing Flash LogsConfiguring Spanning Tree Configuring Classic Spanning Tree Configuring Classic Spanning TreeDefining STP Properties Complete the Spanning Tree State and Bridge Settings fields Click Configure. The STP Interface Configuration Page opens Defining STP InterfacesClick Layer 2 Spanning Tree. The Spanning Tree Page opens Allied Telesis AT-8000S Switch STP Modify Interface Configuration Rstp Configuring Rapid Spanning TreeModify Rstp Configuring Rapid Spanning TreeConfiguring Multiple Spanning Tree Configuring Multiple Spanning Tree Defining Mstp PropertiesDefine the Region Name, Revision, and Max Hops fields Defining Mstp Interfaces Mstp Interface SettingsConfiguring Spanning Tree Defining Mstp Instances Mstp Instance SettingsConfiguring Spanning Tree Configuring Multicast Forwarding Configuring Igmp Snooping Configuring Igmp SnoopingClick Modify. The Igmp Snooping Settings Page opens Igmp Snooping SettingsDefining Multicast Bridging Groups Defining Multicast Bridging GroupsCheck the Enable Bridge Multicast Filtering checkbox Click Create. The Add Multicast Group Page opensClick Modify. The Modify Multicast Group Page opens Defining Multicast Forward All Settings Defining Multicast Forward All SettingsClick Modify. The Modify Multicast Forward All Page opens Modify Multicast Forward AllConfiguring Multicast Forwarding Configuring Snmp Snmp Overview Snmp OverviewSnmp Global Enabling SnmpEnabling Snmp Snmp Communities Basic Table Defining Snmp CommunitiesDefining Snmp Communities Click Modify. The Snmp Community Settings Page opensSnmp Group Defining Snmp GroupsDefining Snmp Groups Click Create. The Create Snmp Group Profile Page opensClick Modify. The Modify Snmp Group Profile Page opens Snmp Users Defining Snmp UsersDefining Snmp Users Click Modify. The Snmp User Settings Page opensClick Create. The Add Snmp VIew Page opens Defining Snmp ViewsDefining Snmp Views Add Snmp VIewDefining Notification Recipients Configuring Snmp NotificationsSNMPv1,2c Notification Recipient Configuring Snmp NotificationsCreate Snmp Notification Recipient Defining Notification FiltersSnmp Notification Filter Settings Configuring Power Over Ethernet Enabling PoE and Setting the Power Threshold Enabling PoE and Setting the Power ThresholdDefining PoE Settings Modify PoE Defining PoE SettingsModify the Admin Mode and Priority Level fields Configuring Power Over Ethernet Configuring Services Enabling Class of Service CoS Enabling Class of Service CoSClick Modify. The CoS Configuration Page opens CoS ConfigurationConfiguring CoS Priorities Configuring CoS PrioritiesClick Configure CoS Select the Configure CoS Priority to Egress Queues valuesClick Configure. The Configure CoS Page opens Mapping Queues Click Configure Dscp Select the Configure Dscp Priority values Click Configure. The Configure Dscp Page opens Mapping Dscp Values to QueuesClick Services Bandwidth. The Bandwidth Page opens Configuring Bandwidth QoSClick Modify. The Bandwidth Configuration Page opens Configuring Bandwidth QoSManaging System Files Restoring the Default Configuration Restoring the Default ConfigurationClick Apply in the Reset to Factory Defaults section Check the Reboot Switch After Resetting to Defaults optionClick Utilities File System The File System Page opens Defining Tftp File Uploads and DownloadsDefining Tftp File Uploads and Downloads Select the Source and the Destination Unit Viewing Integrated Cable Tests Viewing Integrated Cable TestsClick Utilities Cable Test. The Cable Test Page opens Copper Cables Extended Feature Viewing Optical Transceivers Viewing Optical TransceiversSelect the Reset Unit No ResetResetting the Device Viewing Statistics Viewing Interface Statistics Viewing Interface StatisticsViewing Interface Statistics Receive Statistics Etherlike Statistics Viewing Etherlike StatisticsOpen the Etherlike Statistics Managing Rmon Statistics Viewing Rmon StatisticsManaging Rmon Statistics Allied Telesis AT-8000S Switch Configuring Rmon History Click Statistics Rmon History. The Rmon History Page opensClick Rmon History. The Create History Entry Page opens Create History Entry Click Modify. The History Control Settings Page opensClick View. The Rmon History Table Page opens Viewing the Rmon History TableAllied Telesis AT-8000S Switch Click Statistics Rmon Events. The Rmon Events Page opens Configuring Rmon EventsClick Modify. The Event Control Settings Page opens Click Create. The Create Event Entry Page opensDefine the Community, Description, Type and Owner fields Click View. The Rmon Events Logs Page opens Viewing the Rmon Events LogsRmon Alarm Defining Rmon AlarmsAdd Alarm Click Modify. The Rmon Alarm Settings Page opens Rmon Alarm SettingsViewing Statistics Managing Stacking Stacking Ring Topology Stacking OverviewStacking Chain Topology Stacking OverviewRemoving and Replacing Stacking Members Stacking Members and Unit IDExchanging Stacking Members Enhanced Stacking Configuring Stacking ManagementConfiguring Stacking Management Connecting a Terminal Initial ConfigurationAppendix A. Downloading Software with CLI Configuration Initial ConfigurationStatic IP Address and Subnet Mask Downloading Software System software file file1 Boot file fileUser Name Standalone Device Software DownloadDownloading Software Stacking Member Software DownloadAllied Telesis AT-8000S Switch Console# copy unit//1/image unit//4/image Appendix B. System Defaults Port Defaults RS-232 Port SettingsConfiguration Defaults Security DefaultsSystem Time Defaults Spanning Tree DefaultsAddress Table Defaults Trunking Defaults Vlan DefaultMulticast Defaults Vlan DefaultIndex SymbolsAccess profiles Sntp
Related manuals
Manual 48 pages 34.24 Kb
Top Page Image Contents