Allied Telesis AT-8000S manual Safety Statements

Page 45

Safety Statements

Electrical Safety Notices

Warning

23. The power source for the gateway unit should be located near the unit and should be easily accessible.

Caution

24.To allow proper cooling of the gateway device, make sure that the air flow around the unit and through its heatsink cooling fins on the rear is not restricted.

Caution

25.Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

Caution

26.Risk of explosion if battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

Attention: Le remplacement de la batterie par une batterie de type incorrect peut provoquer un danger d’explosion. La remplacer uniquement par une batterie du même type ou de type équivalent recommandée par le constructeur. Les batteries doivent être éliminées conformément aux instructions du constructeur.

Warning

27. For centralized DC power connection, install only in a restricted access area.

Warning

28.A tray cable is required to connect the power source if the unit is powered by centralized DC power. The tray cable must be a UL listed Type TC tray cable and rated at 600 V and 90 degrees C, with three conductors, minimum 14 AWG.

Warning

29.Mounting of the equipment in the rack should be such that a hazardous condition is not created due to uneven mechanical loading.

Page 45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Allied Telesis AT-8000S Installation GuidePage Table of Contents Stacking Allied Telesis AT-8000S Switch Switch Installation GuideTable of Contents Installation Guide Allied Telesis AT-8000S SwitchPreface How This Guide is OrganizedContacting Allied Telesis Contacting Allied TelesisAllied Telesis AT-8000SSwitch Switch Installation GuideProduct Description Ieee Standards FeaturesProduct Description Ieee 802.3 10Base-T Ieee 802.3u 100Base-TXAT-8000S/16 Back Panel AT-8000S/16 Front PanelAT-8000S/24 Back Panel AT-8000S/24 Front PanelAT-8000S/24POE Back Panel AT-8000S/24POE Front PanelAT-8000S/48 Back Panel AT-8000S/48 Front PanelAT-8000S/48POE Back Panel AT-8000S/48POE Front PanelLED Definitions Ports DescriptionMode LEDs Mode LED Indications LED Description24/48 Port Device Stacking LEDs 10/100 Base-T Fast Ethernet RJ-45 Port LEDs Port LEDsPort LEDs Stacking LED Indications LED Description10/100/1000 Base-T/Combo Ethernet RJ-45 Port LEDs 10/100Base-T Fast Ethernet RJ-45 Port LED IndicationsPort Description LED Indication 24/48 Port Device SFP/Combo Port LEDs Combo Port LED Indications Port DescriptionSFP Port LED Indications Port Description Diagnostic LED Power LEDDiagnostics LED Indications LED Description 24/48 Port Device System LEDsStacking Ports LEDs Stacking Ports LEDsInstallation Preparing for InstallationSafety Precautions Preparing for Installation InstallationUnpacking Site RequirementsDesktop or Shelf Installation Installing the DevicePackage Contents Unpacking EssentialsInstalling Rubber Feet Rack InstallationConnecting the Device Connecting the Switch to a TerminalConnecting the Device AC Power Connection Installation Understanding the Stack Topology StackingStacking Members and Unit ID Stacking Chain TopologyStacking Stacking Chain TopologyPress Return or Esc. to abort and enter prom Configuring StackingEnter unit working mode 1 standalone, 2 stacking Configuring StackingConfiguration Overview Initial ConfigurationConfiguration Static IP Address and Subnet MaskInitial Configuration ConfigurationUser Name Cannot connect using Telnet, Web browser, or Snmp software TroubleshootingForgot or lost the password Device not operating correctlyTroubleshooting Appendix A. Technical Specifications Compliance Standards Technical SpecificationsCable, Port, and Pinout Information Pin Connections for the 10/100/1000 Ethernet InterfaceTxRx 2+ TxRx 3+ TxRx 4+ Technical Specifications Appendix B. Safety Statements Laser Safety NoticesElectrical Safety Notices Electrical Safety Notices Safety StatementsAllied Telesis AT-8000SSwitch Safety Statements Allied Telesis AT-8000SSwitch Telecommunications Compliance Notices Telecommunications Compliance NoticesIndex
Related manuals
Manual 188 pages 38.01 Kb

AT-8000S specifications

The Allied Telesis AT-8000S series switches are a range of advanced Layer 2 Ethernet switches designed for efficient networking in various environments. Engineered with performance, reliability, and cost-effectiveness in mind, these switches are ideal for businesses seeking to enhance their network infrastructure.

One of the main features of the AT-8000S series is its high-speed data forwarding capabilities. With support for 10/100/1000 Mbps Ethernet ports, these switches provide fast and reliable connections, enabling seamless data transfer and enhanced communication between devices. The non-blocking switching architecture ensures that full bandwidth is available at all times, maximizing throughput and reducing latency in network traffic.

The AT-8000S series incorporates advanced Layer 2 switching technologies, such as VLAN support, allowing users to segment network traffic for improved performance and security. Virtual Local Area Networks (VLANs) help isolate sensitive data and reduce unnecessary broadcast traffic, enhancing the overall performance of the network.

Quality of Service (QoS) is another significant feature integrated into these switches, prioritizing different classes of network traffic. This functionality ensures that critical applications receive the necessary bandwidth and minimal latency, which is imperative for voice over IP, video conferencing, and other latency-sensitive applications.

In terms of network management, the AT-8000S series provides a variety of options, including an intuitive web-based interface, SNMP support, and the ability to manage switch configurations through console access. This flexibility allows network administrators to monitor performance and manage configurations easily.

The switches are built for durability, featuring a robust design suitable for deployment in various environments, including temperature-sensitive areas. Power over Ethernet (PoE) capability is also available in certain models, allowing network devices like IP cameras and wireless access points to receive power through the same cable as data, simplifying installation and reducing clutter.

Allied Telesis emphasizes security within the AT-8000S series, with features such as port security, DHCP snooping, and IEEE 802.1X authentication to safeguard against unauthorized access and potential threats.

Overall, the Allied Telesis AT-8000S series provides a comprehensive networking solution tailored for modern business needs, combining performance, flexibility, and security to support a growing array of applications and devices within the network.
Top Page Image Contents