Allied Telesis AT-X510-28GSX manual Confirming Status VCStack Feature, Show interface port1.0.51

Page 78

Chapter 5: Powering On the Switch

awplus# write

Building configuration ...

[OK]

awplus#

Confirming the

Status of the

VCStack Feature

Figure 39. Saving the Changes with the WRITE Command

9.Enter the REBOOT command to reboot the switch.

10.At the confirmation prompt, type “Y” for yes.

11.Wait for the switch to initialize its management software and afterwards examine the Switch ID LED. The switch is ready for normal network operations as a stand-alone unit when its ID number is “0.” Refer to the Software Reference for x510 Series Switches, AlliedWare Plus Operating System, for instructions on how to configure the operating parameters. If the number is not “0,” repeat this procedure.

Another way to confirm that VCStack is disabled on the switch is by displaying the status of the last two SFP+ slots on the switch. These are slots 27 and 28 on the 28-port switches and slots 51 and 52 on the 52-port switches. If VCStack is disabled, you should be able to display the status of the slots even when they do not have transceivers. If VCStack is not disabled, the switch displays a message that it cannot find the slots. To view the status of the stacking slots, perform this procedure:

1.Start a management session on the switch. For directions, refer to “Configuring the Switch for Stand-alone Operations” on page 74.

2.Log on to the switch. The default user name is “manager” and the password is “friend”.

3.From either the User Exec mode or Privileged Exec mode, enter the SHOW INTERFACE command to display the status of one of the last two SFP+ slots on the switch. For example, for the AT-x510-28GTX Switch, enter this command to view the status of slot 27:

show interface port1.0.27

4.For the AT-x510-52GTX Switch, enter this command to view the status of slot 51:

show interface port1.0.51

If VCStack is disabled, the switch displays the status of the designated slot. An example is shown in Figure 40 on page 79.

78

Page 77 Page 79
Image 78
Page 77 Page 79
Contents Installation Guide for Stand-alone Switches Copyright 2013 Allied Telesis, Inc Electrical Safety and Emissions Standards Translated Safety Statements Contents Page Figures Figures Tables Tables Preface Document Conventions Contacting Allied Telesis Preface Overview ChapterFeatures X510 Models 10/100/1000 Mbps Twisted Pair PortsSFP Slots X510 Series Installation Guide for Stand-alone Switches Overview Front panels of the x510 Series switches are shown Front and Back PanelsAT-x510-28GSX 10/100/1000Base-T and 100/1000Base-FX Back Panel of the AT-x510-28GPX and AT-x510-52GPX Management Panel X510 Series Management PanelSpeed Duplex Mode Wiring Configuration 10/100/1000Base-T Twisted Pair PortsDistance Cable Requirements Port Pinouts Cable Type 10Mbps 100Mbps 1000MbpsPower Over Ethernet PoE StandardsMaximum Power Class Output from a Switch PD Power Range 1000Mbps Cable Type Non PoE PoE+ Port Prioritization Wiring Implementation SFP+ Slots Stacking SFP+ Slots Transceiver Model Cable Type DistanceEco-friendly Button LEDs LEDs for the Twisted Pair PortsLED PoE LEDs for the SFP Slots LEDs for the SFP+ Slots Switch ID LED Switch ID LED Switch ID LEDs in the Low Power Mode USB Port Console Port Power Supplies Overview Beginning the Installation Reviewing Safety Precautions X510 Series Installation Guide for Stand-alone Switches Beginning the Installation X510 Series Installation Guide for Stand-alone Switches Choosing a Site for the Switch Unpacking the Switch Beginning the Installation Installing the Switch on a Table or in an Equipment Rack Installing the Switch on a Table or Desktop Installing the Switch in an Equipment Rack Removing the Rubber FeetAttaching the Equipment Rack Brackets X510 Series Installation Guide for Stand-alone Switches Installing the Switch on a Table or in an Equipment Rack Cabling the Networking Ports Cabling the Twisted Pair Ports X510 Series Installation Guide for Stand-alone Switches Installing SFP and SFP+ Transceivers Installing SFP Modules in the AT-x510-28GSX Switch Cabling the Networking Ports SFP Handle Installing SFP SFP+ Modules Removing the Dust Cover from an SFP or SFP+ Transceiver SFP Handle Powering On the Switch Powering On the Switch Switch Initialization Messages Monitoring Initialization ProcessesSwitch Initialization Messages X510 Series Installation Guide for Stand-alone Switches Configuring the Switch for Stand-alone Operations Starting a Local Management SessionX510 Series Installation Guide for Stand-alone Switches Disabling VCStack No stack id enable Confirming Status VCStack Feature Show interface port1.0.51Status of a Stacking Slot When VCStack is Enabled Port1.0.n Troubleshooting Troubleshooting X510 Series Installation Guide for Stand-alone Switches Troubleshooting Technical Specifications Physical SpecificationsAppendix a Environmental Specifications Power SpecificationsCertifications RJ-45 Twisted Pair Port PinoutsRJ-45 Style Serial Console Port Pinouts RX+ TX+Transmit Data Ground Receive Data Looped to pin Appendix a Technical Specifications

AT-X510-28GPX, AT-X510-28GSX, AT-X510-52GPX, AT-X510-28GTX, AT-X510-52GTX specifications

Allied Telesis has made significant strides in network infrastructure solutions with its AT-X510 series of managed Ethernet switches. The series includes models such as the AT-X510-28GTX, AT-X510-28GPX, AT-X510-52GTX, AT-X510-28GSX, and AT-X510-52GPX. These switches combine performance, flexibility, and ease of management to meet the demands of various networking environments.

One of the standout features of the AT-X510 series is its robust performance capabilities. These switches are equipped with advanced Layer 2 switching functionalities that support a range of protocols and enhance overall network efficiency. With high forwarding capacities, they ensure that data is transmitted quickly, making them ideal for bandwidth-intensive applications such as video conferencing and cloud services.

Another significant advantage of the AT-X510 series is Power over Ethernet (PoE) support, particularly in the GPX and GSX models. This feature allows the switches to deliver power to connected devices like IP cameras, Wi-Fi access points, and VoIP phones without requiring separate power supplies. This consolidates cabling, simplifies installation, and enhances flexibility in device placement.

The AT-X510 switches also incorporate advanced security functionalities like IEEE 802.1X port-based access control, which ensures that only authorized devices can connect to the network. This is particularly critical in environments where data security is a top priority. Additionally, the switches support VLANs (Virtual Local Area Networks), which help isolate network traffic, enhance performance, and provide an additional layer of security.

Management and configuration of the AT-X510 series are streamlined through an intuitive web-based interface and support for SNMP (Simple Network Management Protocol). This simplifies monitoring and troubleshooting, allowing administrators to manage the network efficiently without extensive training.

The hardware design of the AT-X510 series is also worth noting. Built with reliability in mind, these switches come with redundant power supply options, ensuring continued operation during power failures. The fanless design in some models also contributes to quieter operation, making them suitable for office environments.

Overall, the Allied Telesis AT-X510 series, including the AT-X510-28GTX, AT-X510-28GPX, AT-X510-52GTX, AT-X510-28GSX, and AT-X510-52GPX, offers a compelling combination of performance, flexibility, and security. These switches cater to the needs of modern networks, allowing businesses to build efficient, secure, and well-managed network infrastructures.
Top Page Image Contents