Allied Telesis 2.6.1 manual Troubleshooting, Install the new file as the preferred GUI

Page 39

Getting Started with the Graphical User Interface (GUI)

39

When the switch has loaded the file into its RAM, it displays the message “File transfer successfully completed”. It then writes the file to FLASH memory, which takes approximately 30 seconds after the message. Once the file has been copied to FLASH, you can enter commands that refer to it.

3.Install the new file as the preferred GUI

If you are updating both the release and the resource file, set the preferred release and restart the switch before installing the GUI as described below.

To set the new GUI resource file as the preferred resource file, use the command:

SET INSTALL=preferred GUI=filename.rsc

You can use the GUI to load the new resource file onto the switch (Management > Software > Upgrade), but you need to use the CLI to install the new file.

If you disabled the GUI to delete the old resource file, enable it again, using the command:

ENABLE GUI

Check that the new GUI resource file is valid for your device, using the command:

SHOW GUI

If it is not, or if the file was corrupted during the download, disable the

GUI, delete the file and try again.

4.Point your web browser at the switch’s IP address

Your browser may have a local copy of the old GUI file stored. If so, you need to delete these temporary files (see “Deleting Temporary Files” on page 40).

Troubleshooting

The GUI resource file has an 8-digit name, with the file extension rsc (for example, d450se01.rsc). To check which resource files are present on the switch use the command:

SHOW FILE

To see which GUI resource file the switch is currently using, and which it will use on bootup, use the command:

SHOW INSTALL

To display information about the GUI resource file that is currently installed, use the command:

SHOW GUI

In particular, this command lets you check the file’s validity. If the file is invalid or damaged, download a new file.

To display information about the switch’s HTTP server, use the commands:

SHOW HTTP SERVER

SHOW HTTP SERVER SESSION

Software Release 2.6.1 C613-02039-00 REV A

Image 39

Contents AT-8800 Series Switch Page Contents AT-8800 Series Switch User Guide Operating the switchMaintenance and Troubleshooting Page Introducing the AT-8800 Series Switch Why Read this User Guide?Chapter AT-8800 Series Switch Documentation Set Where To Find More InformationFeatures of the AT-8800 Series Switch Online Technical SupportIntroduction Software Features Management FeaturesSpecial Feature Licences Do if You Clear Flash Memory Completely on This Chapter Getting Started with the Command Line Interface CLIConnecting a Terminal or PC Terminal Communication ParametersParameters for terminal communication Value Assigning an IP Address Enter the password at the password promptGetting Started with the Command Line Interface CLI LoggingTo change the IP address for an interface, enter the command Setting RoutesChanging a Password Choosing a PasswordTo add a static route, enter the command Not available Using the CommandsGetting Command Line Help To display the current help file, enter the commandAliases Setting System Parameters Enabling Special Feature LicencesGetting Started with the Graphical User Interface GUI Getting Started with the Graphical User Interface GUISupported browsers and operating systems What is the GUI?Accessing the Switch via the GUI Browser and PC SetupHttp Proxy Servers See Option 2 Installing the Switch into the LAN on Establishing a Connection to the SwitchSee Option 3 Connecting to an Installed Switch on See Option 1 Configuring the Switch before Installation onOption 1 Configuring the Switch before Installation Use this procedure ifSee Http Proxy Servers on page 23 for more information Plug the switch into the LAN Option 2 Installing the Switch into the LANDefault username is manager At the login prompt, enter the user name and passwordAssign the vlan1 interface an IP address See Secure Access on page 29 for more informationIf necessary, bypass the Http proxy server Option 3 Connecting to an Installed SwitchFind out the IP address of the switch’s interface Select a PCCreate a Security Officer user account Secure AccessThen enter the password for CIPHER, sbr4y3 To enable system security, use the commandTo create an RSA key pair, use the command System Status System StatusQuality of Service and traffic filters Using the GUI Navigation and FeaturesConfiguration Menu Using Configuration PagesAn example of a configuration page with a selection table Editable Fields Monitoring Menu Management MenuDiagnostics Menu Changing the PasswordContext Sensitive GUI Help Saving Configuration Entered with the GUI Combining GUI and CLI ConfigurationConfiguring Multiple Devices Upgrading the GUI To upgrade the GUIThen delete the GUI resource file, using the command Load the new file onto the switchTroubleshooting Install the new file as the preferred GUIPoint your web browser at the switch’s IP address Deleting Temporary Files Accessing the Switch via the GUITraffic Flow Time and NTP SolutionSolutions IP Addresses and DhcpLoading Software Page A Security Officer prompt looks like Using Scripts onUser Accounts and Privileges Snmp and MIBs onLogin Normal Mode and Security Mode To display the current operating mode, enter the commandOperating the switch Specific Parameters Storing Files in Flash Memory Remote ManagementExample output from the Show File command Using ScriptsStoring Multiple Scripts Saving the Switch’s ConfigurationLoading and Uploading Files File Naming ConventionsFile extensions and file types Extension File type/function SPA Loading FilesDownload the patch file Setting Loader DefaultsExample Load a Patch File Using Http To load a patch file Configure the LoaderTo upload a log file Uploading Files From the SwitchExample Upload a Configuration File Using Tftp More informationUpgrading Switch Software Example Upgrade to a New Software Release Using To upgrade to a new software releaseLoad the new release file onto the switch Test the release Enter the licence password for the software releaseMake the release the default permanent release Enter licence information for the releaseExample Upgrade to a new patch file To upgrade to a new patch fileCheck that the file is successfully loaded Snmp and MIBs Using the Built-in EditorFor More About Operations and Facilities Where interface is the name of an interface, such as vlan11AT-8800 Series Switch User Guide Enabling and Disabling Switch Ports Switch PortsTo display information about switch ports, use the command To enable or disable a switch port, use the commandsSTP Autonegotiation of Port Speed and Duplex Mode Speed 10/100 Port TrunkingShow VLAN=ALL Packet Storm Protection Layer 2 SwitchingPort Mirroring Port security Virtual Local Area Networks VLANs Example output from the Show Switch Port Intrusion commandTpid Vlan TaggingFormat of user priority and Vlan data in an Ethernet frame Vlan Membership using Vlan Tags Vlan membership of example of a network using tagged ports Vlan Membership of Untagged PacketsMember ports Vlans with untagged ports Creating VLANsTo destroy a VLAN, use the command To add tagged ports to a VLAN, use the commandSummary of Vlan tagging rules Protected VLANsVlan Interaction with STPs and Trunk Groups Layer 2 Switching Process Generic Vlan Registration Protocol GvrpIngress Rules Learning Process Forwarding Process Layer 2 Filtering Example output from the Show Switch Filter command Egress Rules Quality of ServiceSpanning Tree Modes Spanning Tree Protocol STPSpanning Tree and Rapid Spanning Tree Port States Spanning tree port states State MeaningRapid Spanning Tree port states State Meaning Configuring STP SET STP=stpnameALL PRIORITY=0..65535 Example output from the Show STP command Do not occur Parameter Meaning Switch Max AgeTo display STP port information, use the command Example output from the Show STP Port command 94AT-8800 Series Switch User GuideTo show STP counters, use the command Discarded 96AT-8800 Series Switch User GuideReceive TransmitIgmp Snooping Interfaces to Layer 3 ProtocolsDisable Igmpsnooping Group List Example output from the Show IP Igmp commandParameters TriggersEvent DescriptionLayer IP Multicasting Then use either of the following commandsDisplays the interfaces enabled for IP routing Figure Internet Protocol IPRouting Information Protocol RIP Novell IPXLayer 103 AppleTalk Example output from the Show IPX Circuit commandLayer 105 Resource Reservation Protocol RsvpPage Maintenance and Troubleshooting Switch startup messages How the Switch Starts UpSet system territory How to Avoid ProblemsWatch for software updates If you accidentally do this, you will need to What to Do if You Clear Flash Memory CompletelyWhat to Do if Passwords are Lost What to Do if the PPP Link Disconnects RegularlyGetting the Most Out of Technical Support Maintenance and Troubleshooting 113 Resetting Switch DefaultsChecking Connections Using Ping To get debugging output, enter the commandTelnet Fails Troubleshooting IP ConfigurationsTo set Ping defaults, enter the command Stop a Ping that is in progress, enter the commandMaintenance and Troubleshooting 115 Troubleshooting Dhcp IP AddressesYour switch is acting as a Dhcp client Your switch is acting as a Dhcp serverNo Routes are Visible to the Remote Router Troubleshooting IPX ConfigurationsTo check that the PPP link is active, enter the command Local Workstations Can Not Access Remote ServersCheck route tables Using Trace Route for IP TrafficTo halt a trace route that is in progress, enter the command