Linksys SRW224 manual RJ-45 Ports, Gigabit Expansion Ports, Console Port

Page 12

24-port 10/100 + 2-Port Gigabit Switch with WebView

RJ-45 Ports

The Switch is equipped with twenty-four auto-sensing RJ-45 ports. These RJ-45 ports support network speeds of either 10Mbps or 100Mbps, and can operate in half and full-duplex modes. Auto-sensing technology enables each port to automatically detect the speed of the device connected to it (10Mbps or 100Mbps), and adjust its speed and duplex accordingly.

To connect a device to a port, you will need to use a network cable. You will need to use Category 5 (or better) cable. For more information on twisted-pair cabling, refer to the Twisted-Pair Cabling section.

The Gigabit Expansion Ports

The Switch is equipped with one miniGBIC port and two Gigabit Ethernet ports that provide for the installation of one expansion module. These ports provide links to high-speed network segments or individual workstations at speeds of up to 1000Mbps (Gigabit Ethernet).

To establish a Gigabit Ethernet connection, you will need to install an MGBT1, MGBSX2, or MGBLH1 Gigabit expansion module and use Category 5e cabling or fiber optic cabling. for more information on fiber optic cabling, refer to the Fiber Optic Cabling section.

The Console Port

The Switch is equipped with a serial port labeled CONSOLE (located on the front of the switch) that allows you to connect to a computer’s serial port (for configuration purposes) using the provided serial cable. You can use HyperTerminal to manage the Switch using the console port.

With this and many other Linksys products, your networking options are limitless. Go to the Linksys website at

www.linksys.com for more information about products that work with the Switch.

Chapter 2: Getting to Know the Switch

6

The Side Panel

Image 12

Contents Port 10/100 + 2-Port Gigabit Switch How to Use this Guide Copyright and TrademarksTable of Contents Port 10/100 + 2-Port Gigabit Switch with WebView List of Figures Front PanelAddrees Field Introduction WelcomeWhat’s in this Guide? Port 10/100 + 2-Port Gigabit Switch with WebView Getting to Know the Switch LEDsPorts Back Panel RJ-45 Ports Gigabit Expansion PortsConsole Port Connecting the Switch OverviewMaximum Cabling Distances Pre-Installation Considerations Hardware InstallationPositioning the Switch Fast Ethernet ConsiderationsPlacement Options Desktop PlacementUplinking the Switch Rack-Mount PlacementConfiguration using the Console Interface Configuring the HyperTerminal ApplicationConfiguring the Switch through the Console Interface LoginSwitch Screens Switch Main MenuSystem Configuration System InformationAdvanced Switch Configuration Password ConfigurationIP Configuration Firmware UpdateRestore System Default Setting 14 Send FileReboot System Return to Main MenuPort Configuration Port StatusLogout Configuring the Switch through the Web Utility Password ScreenAdvanced Switch Configuration Figure System TabPassword Setting System Tab-Username/Password SettingClick Apply when finished with your changes Port TabVlan Configuration 802.1Q Vlan ModeTrunk Tab Vlan TabAdvanced 802.1Q Vlan Setting Edit a 802.1Q Vlan GroupPortBased Vlan Mode Add a PortBased Vlan GroupQoS Configuration Logout TabAppendix a Fast Ethernet and Gigabit Ethernet About Fast EthernetAbout Gigabit Ethernet Appendix B Cabling Twisted Pair CablingCrimping your own Network Cables Figure B-2 Straight-Through Cable Fiber Optic Cabling Appendix D Glossary Port 10/100 + 2-Port Gigabit Switch with WebView Port 10/100 + 2-Port Gigabit Switch with WebView Port 10/100 + 2-Port Gigabit Switch with WebView Port 10/100 + 2-Port Gigabit Switch with WebView Port 10/100 + 2-Port Gigabit Switch with WebView Appendix C Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix E Specifications Appendix F Warranty Information Limited WarrantyAppendix G Regulatory Information FCC StatementAppendix H Contact Information