Advantech AIMB-766 user manual Input/Output, Ethernet LAN, Industrial Features

Page 17

1.3.3Input/Output

!PCIe slots: 1 PCIe x16 expansion slot and 2 PCIe x1 expansion slot

!PCI Bus: 4 PCI slots, 32-bit, 33 MHz PCI 2.2 compliant

!Enhanced parallel port: Configured to LPT1, LPT2, LPT3, or disabled. Stan- dard DB-25 female connector provided. Supports EPP/SPP/ECP

!Serial ports: Four serial ports, one of RS-232/422/485 and three of RS-232. DB-9 connector located in rear panel is RS-232

!Keyboard and PS/2 mouse connector: Two 6-pin mini-DIN connectors are located on the mounting bracket for easy connection to a PS/2 keyboard and mouse

!USB port: Supports up to 12 USB 2.0 ports with transmission rates up to 480 Mbps

1.3.4Ethernet LAN

!Supports single/dual 10/100/1000Base-T Ethernet port(s) via PCIe x1 bus which provides a 500 MB/s data transmission rate.

!Interface: 10/100/1000Base-T

!Controller: LAN1: Intel 82766DM, LAN2: Intel 82573L

1.3.5Industrial Features

!Watchdog timer: Can generate a system reset or NC. The watchdog timer is programmable, with each unit equal to one second or one minute (255 levels)

1.3.6Mechanical and Environmental Specifications

!Operating temperature: 0 ~ 55°C (32 ~ 131° F, Depending on CPU)

!Storage temperature: -20 ~ 70° C (-4 ~ 158° F)

!Humidity: 5 ~ 95% non-condensing

!Power supply voltage: +3.3 V, +5 V, ±12 V, 5 Vsb

!Power consumption:

Maximum: +5 V at 3.58 A, +3.3 V at 2.86 A, +12 V at 3.52 A, +5 Vsb at 0.74 A, -12 V at 0.02 A (Intel Core 2 Quad9300 2.5 GHz (1333 MHz FSB), 4 x 1 GB DDR2 800 SDRAM)

!Board size: 304.8 x 228.6 mm (12" x 9.6")

!Board weight: 0.5 kg (1.68 lb)

Chapter 1 Hardware Configuration

5

AIMB-766 User Manual

Image 17
Contents AIMB-766 Copyright Acknowledgements Message to the Customer Advantech Customer ServicesFCC Declaration of ConformityBrand Size Speed Type ECC Vendor PN Advantech PN Memory Memory CompatibilityAIMB-766 Feature Comparison Product Warranty 2 yearsInitial Inspection Viii Contents Bios Operation Appendix B Appendix aTable B.7 Keyboard and Mouse Connector KBMS1 Chapter Introduction Features Hardware ConfigurationMemory SpecificationsSystem Mechanical and Environmental Specifications Industrial FeaturesInput/Output Ethernet LANJumper list Jumpers and ConnectorsUSB78 Jumper and Connector Locations Board Layout Jumper and Connector LocationsAIMB-766 Block Diagram AIMB-766 Block DiagramSafety Precautions Cmos clear CMOS1 Jumper SettingsHow to set jumpers Watchdog timer output JWDT1 System Memory Memory Installation ProceduresCache Memory CPU FSB and memory speedProcessor Installation PCI Bus Routing Table Page Connecting Peripherals Primary IDE1 IDE Connector Floppy Drive Connector FDD1 Connecting PeripheralsParallel Port LPT1 LAN1USB12 LAN2USB34 USB56 USB78 VGA Connector VGA1 Serial Ports COM1, COM2, COM3 & COM4 PS/2 Keyboard and Mouse Connector KBMS1 External Keyboard & Mouse KBMS2 CPU Fan Connector CPUFAN1 System FAN Connector SYSFAN1 and SYSFAN2 External Speaker JFP2 pins 1, 3, 5 Front Panel Connectors JFP1, JFP2 & JFP3Power LED and Keyboard Lock JFP3 Reset Connector JFP1 pins 3 HDD LED Connector JFP2 pins 2ATX Soft Power Switch JFP1 pins 1 Line Out, Mic In Connector AUDIO1 14 8-pin Alarm Board Connector VOLT1 Case Open Connector JCASE1 Front Panel LAN Indicator Connector LANLED1 Page PCI Slots PCI 1 ~ PCI PCIe x16 Expansion Slot PCIEX161 PCIEX11 PCIEX12 SPI Flash connectorSPICN1 Auxiliary 4-pin power connector ATX1TPM connector 20-1 pin Tpmslot Page Bios Operation Setup program initial screen Entering Setup Bios OperationSystem time / System date Main SetupAdvanced Bios features setup screen Advanced Bios Features SetupHardware Prefetcher CPU ConfigurationIDE Configuration Sata Configuration IDE ConfigurationFloppy a Super I/O ConfigurationCPU Warning Temperature Hardware Health ConfigurationAcpi Settings Acpi SettingsAdvanced Acpi Configuration General Acpi ConfigurationApic Acpi SCI IRQ South Bridge Acpi ConfigurationPower Button Mode APM ConfigurationRemote Access Configure Remote Access Type and parameters15 Trusted Computing Trusted ComputingPCI Latency Timer Advanced PCI/PnP SettingsClear Nvram Plug and Play O/S17 Boot Setup Utility Boot SettingsBoot settings Configuration Security Setup20 Advanced Chipset Settings Advanced Chipset Settings22 Video function configuration Dvmt model select North Bridge Chipset Configuration23 South Bridge Configuration South Bridge Chipset Configuration24 South Bridge Chipset Configuration ME Subsystem ConfigurationDiscard Changes and Exit Exit OptionSave Changes and Exit Load Fail-Safe Defaults Load Optimal DefaultsChipset Software Installation Utility Before you begin Windows XP Driver Setup Page VGA Setup Windows Vista/XP/2000 Driver Setup LAN Configuration Installation Win XP Driver Setup LAN Page AMT Setup Intel AMT Overview Windows XP Intel ME Management Engine Interface SetupAMT Setup Please click Next to continue the installation Windows XP AMT ME Driver Setup Page AMT Setup Page Appendix a Programming the Watchdog Timer Watchdog timer overviewAppendix a Programming the Watchdog Timer Example Programs Table A.1 Watchdog timer registersAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Page Appendix B Table B.1 IDE hard drive connector IDE1 IDE Hard Drive Connector IDE1Appendix B I/O Pin Assignments USB Header USB56, USB78, USB910 USB1112 RS-232 Interface COM1, COM2, COM3 & COM4 External Keyboard Connector KBMS2 Power LED and Keyboard Lock JFP3 Infrared IR connector JIR110 CPU/System Fan Power Connector SYSFAN1 HDD LED Connector JFP2 External Speaker Connector JFP2Reset Connector JFP1 SM Bus Connector JFP2 ATX Soft Power Switch JFP116 H/W Monitor Alarm JOBS1 LAN2USB34 18 USB/LAN ports LAN1USB12Audio Input from CD-ROM CDIN1 Front Panel Audio Connector FP Audio22 8-pin Alarm Board Connector VOLT1 Front Panel LAN LED Connector LANLED1 TPMSLOT1 TPM module connector SPICN1 SPI fresh card pin connectorDMA Channel Assignments System I/O Ports30 1st MB Memory Map Interrupt Assignments