Advantech AIMB-766 user manual Declaration of Conformity, Fcc

Page 4

Declaration of Conformity

FCC

This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the following two conditions:

!This device may not cause harmful interference

!This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A dig- ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro- vide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Opera- tion of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. The user is advised that any equipment changes or modifications not expressly approved by the party responsible for compliance would void the compliance to FCC regula- tions and therefore, the user's authority to operate the equipment.

Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer's instructions.

AIMB-766 User Manual

iv

Image 4
Contents AIMB-766 Copyright Acknowledgements Advantech Customer Services Message to the CustomerDeclaration of Conformity FCCMemory Compatibility Brand Size Speed Type ECC Vendor PN Advantech PN MemoryProduct Warranty 2 years AIMB-766 Feature ComparisonInitial Inspection Viii Contents Bios Operation Appendix a Appendix BTable B.7 Keyboard and Mouse Connector KBMS1 Chapter Introduction Hardware Configuration FeaturesSystem SpecificationsMemory Industrial Features Mechanical and Environmental SpecificationsInput/Output Ethernet LANJumpers and Connectors Jumper listUSB78 Board Layout Jumper and Connector Locations Jumper and Connector LocationsAIMB-766 Block Diagram AIMB-766 Block DiagramSafety Precautions How to set jumpers Jumper SettingsCmos clear CMOS1 Watchdog timer output JWDT1 Memory Installation Procedures System MemoryCache Memory CPU FSB and memory speedProcessor Installation PCI Bus Routing Table Page Connecting Peripherals Primary IDE1 IDE Connector Connecting Peripherals Floppy Drive Connector FDD1Parallel Port LPT1 LAN1USB12 LAN2USB34 USB56 USB78 VGA Connector VGA1 Serial Ports COM1, COM2, COM3 & COM4 PS/2 Keyboard and Mouse Connector KBMS1 External Keyboard & Mouse KBMS2 CPU Fan Connector CPUFAN1 System FAN Connector SYSFAN1 and SYSFAN2 Power LED and Keyboard Lock JFP3 Front Panel Connectors JFP1, JFP2 & JFP3External Speaker JFP2 pins 1, 3, 5 ATX Soft Power Switch JFP1 pins 1 HDD LED Connector JFP2 pins 2Reset Connector JFP1 pins 3 Line Out, Mic In Connector AUDIO1 14 8-pin Alarm Board Connector VOLT1 Case Open Connector JCASE1 Front Panel LAN Indicator Connector LANLED1 Page PCI Slots PCI 1 ~ PCI PCIe x16 Expansion Slot PCIEX161 PCIEX11 PCIEX12 TPM connector 20-1 pin Tpmslot Auxiliary 4-pin power connector ATX1SPI Flash connectorSPICN1 Page Bios Operation Setup program initial screen Bios Operation Entering SetupMain Setup System time / System dateAdvanced Bios Features Setup Advanced Bios features setup screenCPU Configuration Hardware PrefetcherIDE Configuration IDE Configuration Sata ConfigurationSuper I/O Configuration Floppy aHardware Health Configuration CPU Warning TemperatureAcpi Settings Acpi SettingsGeneral Acpi Configuration Advanced Acpi ConfigurationSouth Bridge Acpi Configuration Apic Acpi SCI IRQAPM Configuration Power Button ModeConfigure Remote Access Type and parameters Remote AccessTrusted Computing 15 Trusted ComputingAdvanced PCI/PnP Settings PCI Latency TimerClear Nvram Plug and Play O/SBoot Settings 17 Boot Setup UtilitySecurity Setup Boot settings ConfigurationAdvanced Chipset Settings 20 Advanced Chipset SettingsNorth Bridge Chipset Configuration 22 Video function configuration Dvmt model selectSouth Bridge Chipset Configuration 23 South Bridge ConfigurationME Subsystem Configuration 24 South Bridge Chipset ConfigurationSave Changes and Exit Exit OptionDiscard Changes and Exit Load Optimal Defaults Load Fail-Safe DefaultsChipset Software Installation Utility Before you begin Windows XP Driver Setup Page VGA Setup Windows Vista/XP/2000 Driver Setup LAN Configuration Installation Win XP Driver Setup LAN Page AMT Setup Windows XP Intel ME Management Engine Interface Setup Intel AMT OverviewAMT Setup Please click Next to continue the installation Windows XP AMT ME Driver Setup Page AMT Setup Page Appendix a Watchdog timer overview Programming the Watchdog TimerAppendix a Programming the Watchdog Timer Table A.1 Watchdog timer registers Example ProgramsAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Page Appendix B IDE Hard Drive Connector IDE1 Table B.1 IDE hard drive connector IDE1Appendix B I/O Pin Assignments USB Header USB56, USB78, USB910 USB1112 RS-232 Interface COM1, COM2, COM3 & COM4 External Keyboard Connector KBMS2 10 CPU/System Fan Power Connector SYSFAN1 Infrared IR connector JIR1Power LED and Keyboard Lock JFP3 Reset Connector JFP1 External Speaker Connector JFP2HDD LED Connector JFP2 16 H/W Monitor Alarm JOBS1 ATX Soft Power Switch JFP1SM Bus Connector JFP2 18 USB/LAN ports LAN1USB12 LAN2USB3422 8-pin Alarm Board Connector VOLT1 Front Panel Audio Connector FP AudioAudio Input from CD-ROM CDIN1 Front Panel LAN LED Connector LANLED1 SPICN1 SPI fresh card pin connector TPMSLOT1 TPM module connectorSystem I/O Ports DMA Channel AssignmentsInterrupt Assignments 30 1st MB Memory Map