Advantech AIMB-250 Should Be Empty But Eisa Board Found, Should Have Eisa Board But Not Found

Page 94

AIMB-250 Series

20. PRESS A KEY TO REBOOT

This will be displayed at the bottom screen when an error occurs that requires you to reboot. Press any key and the system will reboot.

21. PRESS F1 TO DISABLE NMI, F2 TO REBOOT

When BIOS detects a Non-maskable Interrupt condition during boot, this will allow you to disable the NMI and continue to boot, or you can reboot the system with the NMI enabled.

22.RAM PARITY ERROR - CHECKING FOR SEGMENT ...

Indicates a parity error in Random Access Memory.

23.Should Be Empty But EISA Board Found

PLEASE RUN EISA CONFIGURATION UTILITY

A valid board ID was found in a slot that was configured as having no board ID.

Note: When either of these errors appears, the system will boot in ISA mode, which allows you to run the EISA Configuration Utility.

24. Should Have EISA Board But Not Found

PLEASE RUN EISA CONFIGURATION UTILITY

The board installed is not responding to the ID request, or no board ID has been found in the indicated slot.

Note: When either of these errors appears, the system will boot in ISA mode, which allows you to run the EISA Configuration Utility.

25. Slot Not Empty

Indicates that a slot designated as empty by the EISA Configuration Utility actually contains a board.

Note: When either of these errors appears, the system will boot in ISA mode, which allows you to run the EISA Configuration Utility.

26. SYSTEM HALTED, (CTRL-ALT-DEL) TO REBOOT ...

Indicates the present boot attempt has been aborted and the system must be rebooted. Press and hold down the CTRL and ALT keys and press DEL.

94 AIMB-250 Series User’s Manual

Image 94

Contents Mini-ITX AIMB-250 Series 1st Ed JanuaryTrademark Acknowledgement FCC StatementCopyright Notice AIMB-250 SeriesMessage to the Customer DisclaimerLife Support Policy User’s ManualTechnical Support Advantech CorpProduct Warranty Contents Bios Setup System HALTED, CTRL-ALT-DEL to Reboot Keyboard Error or no Keyboard PresentMemory Size has Changed Since Last Boot Offending Address not FoundHard Disks fail → Unable to recalibrate fixed disk Safety Precautions Packing ListRevision Date Comment Document Amendment HistoryJan Initial release Manual Objectives System Specifications SystemDisplay Mechanical & Environmental Block Diagram Architecture OverviewUser’s Manual Intel 855GME and ICH4 AIMB-250 Series ECC Dram Interface Intel 855GME PCI Interface8 USB VIA VT1616 Audio CodecAIMB-250 Series Chrontel CH7009A TV/DVI Transmitter Page AIMB-250 Series Winbond W83627HF Compact Flash InterfaceHardware Configuration Product Overview Installation Procedure Processor Installation Installing Pentium M CPUInstalling the Fan and Heat Sink Removing CPUUser’s Manual Main Memory DIMM1AIMB-250 Series Label Function Jumper and Connector ListJP2, JP3 Connectors KBMS1 2 COM1 Pin 9 Signal Select JP1 +5V Ring +12V Setting Jumpers & ConnectorsClear Cmos JBAT1 Protect RS-422 RS-422 RS-485 RS-485Vccsb ATX Power Connector ATXPWR1BIT1 BIT2 OFF Pwrok GNDSignal Description CPU Fan Connector CFAN1 User’s Manual CPU Fan Connector CFAN1TAC COM AIMB-250 Series Parallel Port Connector & VGA Connector CN1Signal Description VGA Connector CN1 RED GND Green DAT Blue Hsync VCC Vsync DCKDTR GND DSR RTS CTS Serial Port 1 Connector in RS-232 Mode CN1DCD DTRAIMB-250 Series Serial Port 1 Connector in RS-422 Mode CN1 Serial Port 1 Connector in RS-485 Mode CN1 Data DATA+ GND12 RJ-45 Ethernet / USB 0 & 1, 4 & 5 Connectors CN3, CN4 AIMB-250 Series Audio Connector CN2 Audio-In13 4/5/8-Wire Touch Screen Connector CN5, optional User’s Manual Floppy Connector FLP1 GND WPT Rdata SIDE1 DskchgAIMB-250 Series Signal Description Floppy Connector FLP MoatsaUser’s Manual Primary IDE Connector IDE1 AIMB-250 Series Secondary IDE Connector IDE2 IOW# RESET#IOR# IordySignal Description LCD Inverter Connector JBKL1 AIMB-250 Series LCD Inverter Connector JBKL1GND Enbkl Signal Description CD-ROM Audio Input Connector JCD1 User’s Manual CD-ROM Audio Input Connector JCD1Serial Port 2 Connector JCOM1 AIMB-250 Series Serial Port 3/4 Connector JCOM2, JCOM3 JCOM2 JCOM3Smbclk Digital Input / Output Connector JDIO1Signal Description Digital Input / Output Connector JDIO1 SmbdataSignal Description Front Panel Connecter JFP1 AIMB-250 Series Front Panel Connector JFP1HDD LED Irrx GND Irtx User’s Manual IrDA Connector JIR1Signal Description IrDA Connecter JIR1 Irrx2CDAT 2CCLK GND AIMB-250 Series Lvds Connector JLVDS1Signal Description Lvds Connector JLVDS1 2CDAT, I 2CCLKCASEOPEN# VTIN3 GND Thrmdn User’s Manual Miscellaneous Setting Connector JMISC1Signal Description Miscellaneous Setting Connecter JMISC1 #MASTERAIMB-250 Series Tmds DVI Connector JTMDS1 Signal Description Tmds Connecter JTMDS1Tvcvb GND TVYFCC2 TVCFCC2 User’s Manual TV Out Connector JTV1Signal Description TV Out Connecter JTV1 TvcvbUSB Connector 4 & 5 JUSB2 AIMB-250 Series USB Connector 2 & 3 JUSB1Signal Description USB Connecter 2, 3, 4 & 5 JUSB1, JUSB2 System Fan Connector 1 & 2 SFAN1, SFAN2 Signal Description System Fan Connector SFAN1, SFAN2Bios Setup Press DEL to enter Setup Starting SetupPress F1 to Continue, DEL to enter Setup Using Setup Navigating Through The Menu BarGetting Help Case of ProblemsUser’s Manual To Display a Sub Menu Main Menu User’s Manual Standard Cmos Features Main Menu SelectionIDE Adapter Setup Quick Power On Self Test User’s Manual Advanced Bios FeaturesCPU Feature Virus WarningTypematic Rate Setting AIMB-250 Series First/Second/Third/Other Boot DeviceBoot Up NumLock Status Select power on state for NumLock Swap Floppy DriveOS Select for Dram 64MB Apic ModeMPS Version Control For OS Report No FDD For WIN95Dram Timing Selectable AIMB-250 Series Advanced Chipset FeaturesActive to Precharge Delay CAS Latency TimeSystem Bios Cacheable User’s Manual Dram RAS# to CAS# DelayDram Data Integrity Mode Video Bios CacheableAIMB-250 Series Memory Hole At 15M-16M Delayed TransactionDelay Prior to Thermal AGP Aperture Size MBUser’s Manual Integrated Peripherals OnChip IDE DeviceOnboard Device IDEUser’s Manual Super IO Device ECP+EPP Watch Dog Timer2E8/IRQ3, Auto IRQ3, IRQ4, IRQ5Acpi Function User’s Manual Power Management SetupPower Management Acpi Suspend TypeAIMB-250 Series Modem Use IRQ Power On By RingResume By Alarm Soft-Off by PWR-BTTNResources Controlled By User’s Manual PnP / PCI ConfigurationReset Configuration Data PCI / VGA Palette SnoopAIMB-250 Series PC Health Status Case Open WarningSpread Spectrum User’s Manual Frequency / Voltage ControlAuto Detect PCI Clk CPU Host / 3V66 / PCI ClockAIMB-250 Series Load Fail-Safe Defaults Load Optimized DefaultsUser’s Manual Set Supervisor / User Password Password Disabled Save & Exit SetupUser’s Manual Exit Without Save Drivers Installation Step Install DriverUser’s Manual Click AIMB-250 Mechanical Drawing Unit mm Award Bios Post Overview Error Messages Post Beep Eisa Configuration Checksum Error Eisa Configuration Is Not CompleteMemory parity Error at User’s Manual Invalid Eisa ConfigurationMemory Address Error at Memory Verify Error atShould Have Eisa Board But Not Found Should Be Empty But Eisa Board FoundSlot Not Empty User’s Manual Wrong Board In Slot Keyboard error or no keyboard presentBios ROM checksum error System halted Manufacturing Post loop40.1Normal Post Code AIMB-250 Series Post CodesE1-EF User’s Manual AIMB-250 Series User’s Manual AIMB-250 Series AIMB-250 User’s Manual101 AIMB-250 Series 40.2Quick Post Codes AIMB-250 User’s Manual103 AIMB-250 Series 40.3S4 Post Codes SMI40.4BootBlock Post Codes