Advantech DVMB-554E user manual Halt On, Standard Cmos Features Screen

Page 43

Head: Number of heads

Precomp: Write precomp

Landing Zone: Landing zone

Sector: Number of sectors

3.3.4 Halt On

This category determines whether system start-up will halt or not when an error is detected during power up.

The options are: No Errors/All Errors/All, But Keyboard/All, But Dis- kette/All, But Disk/Key

3.3.5 Memory

This category displays base memory, extended memory, and total mem- ory detected during POST (Power On Self Test).

Figure 3.2: Standard CMOS Features Screen

43

Image 43
Contents DVMB-554E Copyright Acknowledgements Message to the Customer Certifications Product warranty Initial Inspection Table of Contents Hardware Configuration Award Bios Setup Page 16 FDD, COM, LPT Port Chipset Installation General Information Introduction Hardware ConfigurationSpecifications FeaturesSystem Input/Output MemoryGraphics Mechanical and environmental specifications Industrial featuresEthernet LAN Jumpers Jumpers and ConnectorsCNX1 Jumper and Connector locations G u r Board Layout Jumper and Connector LocationsDVMB-554E Block Diagram DVMB-554E Block DiagramSafety Precautions How to set jumpers Jumper SettingsCmos clear J3 Watchdog timer output J4 Watchdog timer output J4Lvds Power 3.3V/5V selector J6 4 COM2 RS 232/422/485 mode selector J2CPU FSB and memory speed Memory Installation ProceduresSystem Memory Cache MemoryProcessor Installation Connecting Peripherals Primary IDE Connector CN11 USB Ports and LAN Ports CN4, CN5, CN9, CN10 LAN LED indicatorSerial port module COM1/COM2 CM1 VGA and DVI connector moduleExternal PS/2 and Composite TV-Out CN2 Fan Connector FN1/FN2/FN3Power LED and Keyboard Lock CN13 Front Panel Connectors CNX1/CN13External Speaker CNX1-17 SM Bus Connector CNX1-29 Reset Connector CNX1-18HDD LED Connector CNX1-19 ATX Soft Power Switch CNX1-21Line Out, Mic In Connector CN3 H/W Monitor Alarm CN12Serial ATA Interface SA1, SA2 Aux Line-In Connector CN7Auxiliary 4-pin power connector ATX1 DVA-210 Connector VDO1Gpio connector GPIO1 Lvds connector VCN1 Lvds connector VCN1LCD Inverter Power connector BKL1 Bios Setup Cmos RAM Auto-backup and Restore Award Bios SetupTime Entering SetupStandard Cmos Setup DateHalt On Standard Cmos Features ScreenAdvanced Bios features screen Advanced Bios FeaturesFirst/Second Boot Device CPU FeaturesHard Disk Boot Priority Quick Power On Self TestApic Mode Boot Up NumLock StatusTypematic Rate Setting Typematic Delay msecMPS Version Control For OS Advanced Chipset FeaturesDram Timing Selectable Dram RAS# to CAS# DelayCAS Latency Time Dram RAS# Precharge Precharge Delay t RASSystem Bios Cacheable Video Bios CacheableOn-Chip Frame Buffer Size Dvmt ModeBoot Display PEG / Onchip VGA ControlInit Display First Integrated PeripheralsOn-Chip Primary / Secondary IDE Device IDE HDD Block ModeIDE DMA Transfer Access Sata ModeUSB Controller Pata IDE ModeOn-Chip Serial ATA Sata PortOnboard LAN1 Control USB 2.0 ControllerUSB Keyboard / Mouse Support 11 AC97 AudioUse IR Pins Uart Mode SelectIR Transmission Delay 20 UR2 Duplex Mode10 Power management setup screen a Power Management SetupVideo Off Method Power ManagementPCI Express PM Function Acpi FunctionPowerOn by Modem Suspend ModeHDD Power Down PowerOn by LANPwron After PWR-Fail PCI Pirq A-D#PCI / VGA Palette Snoop PnP/PCI ConfigurationsReset Configuration Data Resources Controlled ByPC Health Status Spread Spectrum Frequency / Voltage ControlSave & Exit Setup Password SettingExit Without Saving Chipset Installation Before you begin Windows XP Driver Setup Page Page VGA Setup Introduction Page Page Video capture installation Video capture installation Page System will show the un-known devices like below window Click the below icon to specify the driver location Page Page Page Page Installation of DVMB-554E Demo Program Page Page Beginning the installation Device Demo Program FunctionalitySwitch Channels Resolution Frame Rate Video Mux Video Standard Snap Buffer Sensor Control Gpio control Micro Control