Advantech PCM-9587 user manual General Information

Page 11

„Watchdog timer: Winbond W83627, 255 levels timer interval, setup by soft- ware

„USB: Four USB 2.0 compliant host ports

„IrDA: N/A

„GPIO: 8-bit general purpose input/output

„Expansion: PC/104 Plus(support 8bit ISA, not support ISA DMA mode), PCI and miniPCI

Solid State Disk

„Supports one 50-pin socket for CFC type I/II

VGA/LCD Interface

„Chipset: Intel 852GM

„Frame buffer: Optimized Shared Memory Architecture, supports up to 64MB frame buffer using system memory

„Interface: 4x AGP VGA/LVDS interface

„Display mode: CRT Modes: pixel resolution up to 1600 x 1200 at 85-Hz and 2048 x 1536 at 75-Hz

„LCD mode: Dual channel LVDS panel support up to UXGA panel resolution with frequency range from 25-MHz to 112-MHz

„LVDS: Supports 2 channel (48-bit) LVDS LCD panel

TV-Out/DVI (TV out optional by request)

„Chipset: Chrontel CH7009

„Supports composite, s-video or RGB output

„Supports NTSC and PAL formats

Ethernet interface

„Chipset:

„Intel 82551ER /82551QM optional

„Ethernet interface:

„IEEE 802.3u 100 BASE-T Fast Ethernet compatible (PCM-9587)

„I/O address switchless setting

„Built-in boot ROM

Audio Function

„Chipset: 6300ESB, Audio codec ALC 650

„Audio controller: AC’97 3D surround stereo sound

„Supports Speaker out, CD-input, Line-in, Line-out, Microphone

Mechanical and Environmental

„Dimensions: (L x W)203 x 146 mm (8" x 5.75")

„Power supply Voltage:ATX, with Vcore 2 phase, +5V power only can work

„Power Requirement: (Celeron M 600 with 256MB)

„

Max: 2.63A@ 5V, 0.03A @ 12V

„

Typical: 2.62A@ 5V, 0.03A @ 12V

„Operating temperature:0 ~ 60° C (32~140° F)

„Operating Humidity:0% ~ 90% Relative Humidity, non-condensing

„Weight: 0.85 kg (weight of total package)

Chapter 1 General Information

3

PCM-9587 User Manual

Image 11
Contents PCM-9587 Copyright Acknowledgements Order Information Optional accessoriesPacking List Technical Support and Assistance Declaration of ConformityContents Software Configuration Appendix a Programming the Gpio and Watchdog Appendix C Appendix EGeneral Information ChapterIntroduction FeaturesSpecifications General Information Board layout dimensions component side Board layout dimensionsInstallation Jumpers Jumpers setting drawingJ5 COM2 RS 232/422/485 Select InstallationConnectors ConnectorsJumper & Connector component side Locating jumpers and ConnectorsClear Cmos J3 Setting JumpersSolid State Disk Installing DIMMsIDE, Cdrom hard drive connector CN15 Connecting the hard driveConnecting the floppy drive Floppy drive connector CN14Parallel port connector CN16 Keyboard and PS/2 mouse connector CN27ATX power ON/OFF switch con. pin 11-12 of CN22 Front Panel Connector CN22Power connectors CN25,CN5 17 VGA/LVDS interface connections CN7, CN8,CN9 COM port connector CN21Audio AC97 Link interfaces CN4 Network boot Ethernet configuration CN11DVI LCD panel connectorCN9 19.1 100Base-T connector CN11DIO connector CN19 USB connectors CN18,CN20LCD Backlight connector CN1 Sata Connector CN23, CN2410 CN13 System FAN connector System FAN connector CN13Page Software Configuration Connections to LCD/ Flat Panel CN8 Connections to Standard LCDsLG LM150X06 1024x76816 colors Lvds LCD This chapter describes how to set Bios configuration data Award Bios SetupSystem test and initialization Award Bios setupSystem configuration verification Entering setupAdvanced Bios Features setup Standard Cmos Features setupIntegrated Peripherals Advanced Chipset Features setup7 PnP/PCI Configurations Power Management SetupFrequency/Voltage Control PC Health StatusSet Password Load Optimized DefaultsExit Without Saving Save & Exit SetupPCI Graphic Dual/Simultaneous Display ChipsetDisplay memory Display typesPCI Graphic Installation for Windows 2000/XP Installation of the PCI Graphic driverPCI Graphic Further Information Audio Setup Windows 2000/XP drivers Driver installationBefore you begin Audio Setup Page LAN Configuration Installation for Windows Installation of Ethernet DriverLAN Configuration Choose Hardware Device Ethernet Controller LAN Configuration Page LAN Configuration Further information Appendix a Programming Gpio and Watchdog TimerGpio Example program-1 Supported Gpio RegisterGpio Registers Appendix a Programming the Gpio and Watchdog Timer Watchdog programming This appendix provides special- ized information regarding Pin AssignmentsTable B.2 TV Out Connector CN2 TV out optional by request TV Out Connector CN2 TV out optional by requestCD-IN Connector CN3 Table B.1 LCD Backlight Connector CN112V and -5V Connector CN6 Audio Output Connector CN4Power input Connector CN5 Table B.8 CN8 Lvds connector VGA Connector CN7Lvds Connector CN8 Table B.7 VGA Connector CN711 10/100M LAN Connector CN11 DVI Connector CN9Gigabit LAN Connector CN10 Optional Table B.13 System FAN Connector CN13 Gigabit LAN LED Connector CN12 OptionalFloppy Disk Drive Connector CN14 Table B.12 Gigabit LAN LED Connector CN12Table B.16 Printer Port Connector CN16 Primary HDD Connector CN15Printer Port Connector CN16 Table B.15 Primary HDD Connector CN15Table B.18 DIO Connector CN19 USB Connector CN18,20Table B.17 USB Connector CN18,20 Table B.19 COM Port Connector CN21 Table B.21 Sata Connector 1 CN23 Sata Connector 1 CN23Table B.20 Front panel Connector CN22 Table B.23 CPU FAN Connector CN25 Sata Connector 2 CN24CPU FAN Connector CN25 Table B.22 Sata Connector 2 CN24Table B.26 CPU FAN Connector wafer boxOptionalCN28 CPU FAN Connector wafer BoxOptionalCN28Table B.25 Keyboard and Mouse Connector CN27 Table B.28 CompactFlash Card Connector CN30 Mini PCI ConnectorCN29CompactFlash Card Connector CN30 Table B.27 Mini PCI Connector CN29Page System Assignments Appendix CTable C.1 System I/O Ports System I/O PortsTable C.3 DMA channel assignments 1st MB memory mapDMA channel assignments Table C.2 1st MB memory mapTable C.4 Interrupt assignments Interrupt assignmentsOptional Extras for the PCM-9587 Appendix DPCM-10586-6200E Cable kit for PCM-9587 Table D.1 PCM-10586-6200E wiring kitMechanical Drawings Appendix EFigure E.1 PCM-9587 Mechanical Drawing component side Mechanical DrawingsAppendix E Mechanical Drawings