Advantech PCM-9587 user manual Copyright Acknowledgements

Page 2

Copyright

The documentation and the software included with this product are copyrighted 2008 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.

Acknowledgements

Award is a trademark of Award Software International, Inc. VIA is a trademark of VIA Technologies, Inc.

IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor- poration.

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows® is a registered trademark of Microsoft Corp. RTL is a trademark of Realtek Semi-Conductor Co., Ltd.

ESS is a trademark of ESS Technology, Inc.

UMC is a trademark of United Microelectronics Corporation. SMI is a trademark of Silicon Motion, Inc.

Creative is a trademark of Creative Technology LTD. CHRONTEL is a trademark of Chrontel Inc.

All other product names or trademarks are properties of their respective owners.

For more information on this and other Advantech products, please visit our websites

at:http://www.advantech.com http://www.advantech.com/eplatform

For technical support and service, please visit our support website at:

http://www.advantech.com/support

This manual is for the PCM-9587.

Part No. 2006958701	Edition 2
Printed in Taiwan	September 2008

PCM-9587 User Manual

ii

Image 2

Contents PCM-9587 Copyright Acknowledgements Order Information Optional accessoriesPacking List Declaration of Conformity Technical Support and AssistanceContents Software Configuration Appendix a Programming the Gpio and Watchdog Appendix E Appendix CChapter General InformationIntroduction FeaturesSpecifications General Information Board layout dimensions Board layout dimensions component sideInstallation Jumpers setting drawing JumpersInstallation J5 COM2 RS 232/422/485 SelectConnectors ConnectorsLocating jumpers and Connectors Jumper & Connector component sideSetting Jumpers Clear Cmos J3Connecting the hard drive Installing DIMMsIDE, Cdrom hard drive connector CN15 Solid State DiskKeyboard and PS/2 mouse connector CN27 Floppy drive connector CN14Parallel port connector CN16 Connecting the floppy driveATX power ON/OFF switch con. pin 11-12 of CN22 Front Panel Connector CN22Power connectors CN25,CN5 17 VGA/LVDS interface connections CN7, CN8,CN9 COM port connector CN21Audio AC97 Link interfaces CN4 19.1 100Base-T connector CN11 Ethernet configuration CN11DVI LCD panel connectorCN9 Network bootSata Connector CN23, CN24 USB connectors CN18,CN20LCD Backlight connector CN1 DIO connector CN19System FAN connector CN13 10 CN13 System FAN connectorPage Software Configuration Connections to LCD/ Flat Panel CN8 Connections to Standard LCDsLG LM150X06 1024x76816 colors Lvds LCD Award Bios Setup This chapter describes how to set Bios configuration dataEntering setup Award Bios setupSystem configuration verification System test and initializationStandard Cmos Features setup Advanced Bios Features setupAdvanced Chipset Features setup Integrated PeripheralsPower Management Setup 7 PnP/PCI ConfigurationsPC Health Status Frequency/Voltage ControlLoad Optimized Defaults Set PasswordSave & Exit Setup Exit Without SavingPCI Graphic Display types ChipsetDisplay memory Dual/Simultaneous DisplayPCI Graphic Installation of the PCI Graphic driver Installation for Windows 2000/XPPCI Graphic Further Information Audio Setup Windows 2000/XP drivers Driver installationBefore you begin Audio Setup Page LAN Configuration Installation of Ethernet Driver Installation for WindowsLAN Configuration Choose Hardware Device Ethernet Controller LAN Configuration Page LAN Configuration Further information Programming Gpio and Watchdog Timer Appendix aGpio Example program-1 Supported Gpio RegisterGpio Registers Appendix a Programming the Gpio and Watchdog Timer Watchdog programming Pin Assignments This appendix provides special- ized information regardingTable B.1 LCD Backlight Connector CN1 TV Out Connector CN2 TV out optional by requestCD-IN Connector CN3 Table B.2 TV Out Connector CN2 TV out optional by request12V and -5V Connector CN6 Audio Output Connector CN4Power input Connector CN5 Table B.7 VGA Connector CN7 VGA Connector CN7Lvds Connector CN8 Table B.8 CN8 Lvds connector11 10/100M LAN Connector CN11 DVI Connector CN9Gigabit LAN Connector CN10 Optional Table B.12 Gigabit LAN LED Connector CN12 Gigabit LAN LED Connector CN12 OptionalFloppy Disk Drive Connector CN14 Table B.13 System FAN Connector CN13Table B.15 Primary HDD Connector CN15 Primary HDD Connector CN15Printer Port Connector CN16 Table B.16 Printer Port Connector CN16Table B.18 DIO Connector CN19 USB Connector CN18,20Table B.17 USB Connector CN18,20 Table B.19 COM Port Connector CN21 Table B.21 Sata Connector 1 CN23 Sata Connector 1 CN23Table B.20 Front panel Connector CN22 Table B.22 Sata Connector 2 CN24 Sata Connector 2 CN24CPU FAN Connector CN25 Table B.23 CPU FAN Connector CN25Table B.26 CPU FAN Connector wafer boxOptionalCN28 CPU FAN Connector wafer BoxOptionalCN28Table B.25 Keyboard and Mouse Connector CN27 Table B.27 Mini PCI Connector CN29 Mini PCI ConnectorCN29CompactFlash Card Connector CN30 Table B.28 CompactFlash Card Connector CN30Page Appendix C System AssignmentsSystem I/O Ports Table C.1 System I/O PortsTable C.2 1st MB memory map 1st MB memory mapDMA channel assignments Table C.3 DMA channel assignmentsInterrupt assignments Table C.4 Interrupt assignmentsAppendix D Optional Extras for the PCM-9587Table D.1 PCM-10586-6200E wiring kit PCM-10586-6200E Cable kit for PCM-9587Appendix E Mechanical DrawingsMechanical Drawings Figure E.1 PCM-9587 Mechanical Drawing component sideAppendix E Mechanical Drawings