Accton Technology ES4324 manual Straight-Through Wiring, Cables

Page 46

B Cables

Table B-1 10/100BASE-TX MDI and MDI-X Port Pinouts

Pin

MDI Signal Name

MDI-X Signal Name

1

Transmit Data plus (TD+)

Receive Data plus (RD+)

2

Transmit Data minus (TD-)

Receive Data minus (RD-)

3

Receive Data plus (RD+)

Transmit Data plus (TD+)

 

 

 

6

Receive Data minus (RD-)

Transmit Data minus (TD-)

4,5,7,8

Not used

Not used

Note: The “+” and “-” signs represent the polarity of the wires that make up each wire pair.

Straight-Through Wiring

If the twisted-pair cable is to join two ports and only one of the ports has an internal crossover (MDI-X), the two pairs of wires must be straight-through. (When auto-negotiation is enabled for any RJ-45 port on the switch, you can use either straight-through or crossover cable to connect to any device type.)

You must connect all four wire pairs as shown in the following diagram to support Gigabit Ethernet connections.

EIA/TIA 568B RJ-45 Wiring Standard 10/100BASE-TX Straight-through Cable

White/Orange Stripe

 

 

Orange

 

 

 

1

White/Green Stripe

1

 

End A

2

Blue

2

End B

 

3

3

 

 

4

 

4

 

 

5

White/Blue Stripe

5

 

 

6

Green

6

 

 

7

7

 

 

8

White/Brown Stripe

8

 

 

 

 

 

Brown

Figure B-2 Straight-through Wiring

B-2

Image 46
Contents Powered by Accton Page Port Gigabit Lite Switch ES4324 E092007-AP-R01 150200057600A Compliances and Safety Warnings CE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance Or Nema 6-15P 15 A, 250 V configuration France et Pérou uniquement Die Aufschrift HAR oder Basec tragen Environmental Statement Viii Contents Making Network Connections Appendix a TroubleshootingAppendix C Specifications Appendix B CablesTables Figures Introduction OverviewNetwork Management Options Switch ArchitectureDescription of Hardware 10/100/1000BASE-T PortsPort and Power Status LEDs LEDConnectivity Features and BenefitsPower Supply Socket ExpandabilityManagement Introduction Introduction to Switching Network PlanningApplication Examples Collapsed BackboneCentral Wiring Closet Central Wiring ClosetRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections VlanApplication Notes Selecting a Site Installing the SwitchEthernet Cabling Package Contents Equipment ChecklistOptional Rack-Mounting Equipment Mounting Rack MountingInstalling the Switch in a Rack Desktop or Shelf MountingInstalling an Optional SFP Transceiver Inserting an SFP Transceiver into a SlotConnecting to a Power Source Power SocketTwisted-Pair Devices Connecting Network DevicesMaking Network Connections Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Wiring Closet ConnectionsFiber Optic SFP Devices Making Connections to SFP Transceivers 1000BASE-T Cable Requirements Connectivity RulesMbps Gigabit Ethernet Collision Domain Mbps Fast Ethernet Collision Domain Mbps Ethernet Collision DomainCable Labeling and Connection Records Diagnosing Switch Indicators Appendix a TroubleshootingPower and Cooling Problems Installation In-Band AccessTwisted-Pair Cable and Pin Assignments Appendix B Cables10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring CablesCrossover Wiring 1000BASE-T Pin AssignmentsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Cable Testing for Existing Category 5 CableFiber Standards Appendix C Specifications Physical CharacteristicsManagement Features Switch FeaturesStandards Compliances Specifications Glossary Fast Ethernet End StationEthernet Full DuplexLAN Segment Media Access Control MACIeee 802.3z LayerSwitched Ports Redundant Power Supply RPSRJ-45 Connector Transmission Control Protocol/Internet Protocol TCP/IPIndex NumericsIndex-2 Page ES4324 E092007-AP-R01 150200057600A