Accton Technology ES4324 manual Or Nema 6-15P 15 A, 250 V configuration

Page 8

Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following:

Power Cord Set

U.S.A. and Canada

The cord set must be UL-approved and CSA certified.

 

 

 

The minimum specifications for the flexible cord are:

 

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

 

- Type SV or SJ

 

- 3-conductor

 

 

 

The cord set must have a rated current capacity of at least 10 A.

 

 

 

The attachment plug must be an earth-grounding type with NEMA 5-15P (15 A,

 

125 V) or NEMA 6-15P (15 A, 250 V) configuration.

 

 

Denmark

The supply plug must comply with Section 107-2-D1, Standard DK2-1a or

 

DK2-5a.

 

 

Switzerland

The supply plug must comply with SEV/ASE 1011.

 

 

U.K.

The supply plug must comply with BS1363 (3-pin 13 A) and be fitted with a 5 A

 

fuse which complies with BS1362.

 

 

 

The mains cord must be <HAR> or <BASEC> marked and be of type

 

HO3VVF3GO.75 (minimum).

 

 

Europe

The supply plug must comply with CEE7/7 (“SCHUKO”).

 

 

 

The mains cord must be <HAR> or <BASEC> marked and be of type

 

HO3VVF3GO.75 (minimum).

 

 

 

IEC-320 receptacle.

 

 

Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch:

AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié.

Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la masse).

Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité.

Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit respecter une configuration qui permet un branchement sur une entrée d’appareil EN 60320/IEC 320.

La prise secteur doit se trouver à proximité de l’appareil et son accès doit être facile. Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique au niveau de cette prise.

L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il est raccordé fonctionne dans les mêmes conditions.

iv

Image 8
Contents Powered by Accton Page Port Gigabit Lite Switch ES4324 E092007-AP-R01 150200057600A Compliances and Safety Warnings CE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance Or Nema 6-15P 15 A, 250 V configuration France et Pérou uniquement Die Aufschrift HAR oder Basec tragen Environmental Statement Viii Contents Appendix a Troubleshooting Appendix C SpecificationsMaking Network Connections Appendix B CablesTables Figures Introduction OverviewSwitch Architecture Description of HardwareNetwork Management Options 10/100/1000BASE-T PortsPort and Power Status LEDs LEDFeatures and Benefits Power Supply SocketConnectivity ExpandabilityManagement Introduction Introduction to Switching Network PlanningApplication Examples Collapsed BackboneCentral Wiring Closet Central Wiring ClosetRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections VlanApplication Notes Ethernet Cabling Installing the SwitchSelecting a Site Optional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack MountingInstalling the Switch in a Rack Desktop or Shelf MountingInstalling an Optional SFP Transceiver Inserting an SFP Transceiver into a SlotConnecting to a Power Source Power SocketConnecting Network Devices Making Network ConnectionsTwisted-Pair Devices Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Wiring Closet ConnectionsFiber Optic SFP Devices Making Connections to SFP Transceivers Mbps Gigabit Ethernet Collision Domain Connectivity Rules1000BASE-T Cable Requirements Mbps Fast Ethernet Collision Domain Mbps Ethernet Collision DomainCable Labeling and Connection Records Power and Cooling Problems Appendix a TroubleshootingDiagnosing Switch Indicators Installation In-Band Access10BASE-T/100BASE-TX Pin Assignments Appendix B CablesTwisted-Pair Cable and Pin Assignments Straight-Through Wiring CablesCrossover Wiring 1000BASE-T Pin AssignmentsFiber Standards Cable Testing for Existing Category 5 CableAdjusting Existing Category 5 Cabling to Run 1000BASE-T Appendix C Specifications Physical CharacteristicsStandards Switch FeaturesManagement Features Compliances Specifications Glossary End Station EthernetFast Ethernet Full DuplexMedia Access Control MAC Ieee 802.3zLAN Segment LayerRedundant Power Supply RPS RJ-45 ConnectorSwitched Ports Transmission Control Protocol/Internet Protocol TCP/IPIndex NumericsIndex-2 Page ES4324 E092007-AP-R01 150200057600A