Acroprint DC7000 manual FCC Warning FCC Compliance on hardware equipped with modem

Page 2

FCC Warning:

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Compliance: (on hardware equipped with modem)

This equipment complies with Part 68 of FCC Rules and the requirements adopted by the ACTA. On the rear housing of this equipment is a label that contains, among other information, a product identifier in the format US:AAEQ##TXXXX. If requested this number must be provided to the telephone company.

This product uses USOC modular telephone jack: R-J11C

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAEQ##TXXX. The digits represented by ## are the REN without the decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

If this equipment, 4G3MM00B1011, causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

2

Image 2
Contents Hardware Manual FCC Warning FCC Compliance on hardware equipped with modem Canada USA Table of Contents Introduction Basic hardware and variationsPage Operating Environment Unpacking and InspectionPower up MountingOperator Interface KeypadsCard Readers Ethernet Port Ethernet PortWireless WiFi Connection RS-232 Serial portStandard Modular Cable Cabling to Host Computer with DB-25 PortCabling to Host Computer with DB-9 Port See Page 24 for USB to RS-232 AdaptorLocal Area Network RS-485 Serial Port RS485 Wiring Diagram RS-485 Serial CablesModem Port Modem Cables Wand Port Pin FunctionWand and Y-Cable Barcode WandParallel Port Parallel Cable Schematic Parallel CableDescription / Illustration Part Number Power Supply 120/240VAC to 12VAC, 3APower Supply Barcode Wand 74-0106-002 HolderExternal Relay Box 120 External BuzzerDescription/Illustration DB-25 RS-232 Host Cable AssemblyDB-9 RS-232 Host Cable Assembly Cable splitterJunction Box Modem Adaptor Cable AssemblyTeflon Cable available by the foot Pocket Badge Rack PlasticAppendix Units with Acroprint Data Collection Firmware For RS485 terminals only Configuring procedure for selecting the Readers Parallel Port Connector on DC7000 Digital IO Mode Printer ModeDC7000 RS232 Connector 3 4 5 6 7 Modem RS485Specifications IO PointsThis page intentionally left blank This page intentionally left blank 06-0333-000 Rev. B

DC7000 specifications

The Acroprint DC7000 is a leading time and attendance solution that caters to the diverse needs of businesses in monitoring employee attendance and managing time effectively. This powerful clocking system is equipped with advanced features and innovative technologies designed to streamline the attendance process while enhancing productivity.

One of the main features of the DC7000 is its versatility in capturing employee time. The device allows for multiple clocking methods, including biometric fingerprint scanning, proximity card readers, and traditional keypad entries. This flexibility provides organizations with the ability to choose the method that best suits their needs, all while ensuring secure and accurate time tracking.

Another significant characteristic of the Acroprint DC7000 is its robust data management capabilities. It can store up to 50,000 transactions and retains attendance records for up to 10,000 employees. Its extensive memory ensures that businesses can operate efficiently without the risk of losing critical data.

The DC7000 also utilizes advanced communication technologies, including USB, Ethernet, and the option for wireless connectivity. This enables seamless integration with existing payroll and HR systems, which can help eliminate the need for manual data entry and reduce human errors. With its compatibility with popular software solutions, the device can export attendance data directly for payroll processing, facilitating quicker and more accurate compensation.

Additionally, the Acroprint DC7000 is designed for user-friendliness, featuring an intuitive interface that makes operation straightforward. The large color display provides clear prompts and feedback, enabling easy navigation through menus for settings, reports, and clocking hours.

In terms of durability, the DC7000 is constructed to withstand the rigors of a busy workplace. Its robust design ensures that it can handle heavy use without compromising functionality. Moreover, the device offers customizable settings, allowing managers to establish attendance policies, such as flexible working hours, overtime calculations, and exception reporting.

In conclusion, the Acroprint DC7000 is a comprehensive time and attendance solution, merging advanced technology with practicality. Its multiple clocking methods, extensive data storage, seamless integration capabilities, and user-friendly design make it an ideal choice for any business looking to enhance their time management processes while ensuring optimal efficiency and accuracy.