Paxar 9800 Series manual J u s t i n g t h e W i d e / N a r r o w K n o b s

Page 27

9.Close the exit cover.

10.Load supplies by following the label loading procedures. You may notice a different color and texture on the platen roller. Linerless supplies do not stick to the textured platen roller.

11.Close the printhead assembly and the cover.

12.Turn on the printer.

13.Verify the alignment of the platen roller with the peel bar or shelf. Press Feed/Cut to position the supply under the printhead.

A d j u s t i n g t h e W i d e / N a r r o w K n o b s

You may need to adjust the two wide/narrow knobs according to the width of your supply. For supply that is more than two inches, adjust the knobs to the wide setting. For supply that is two inches or less, adjust the knobs to the narrow setting. For linerless supply, use the narrow setting (knobs are up). If you experience ribbon smudging in cold, dry environments, adjust the wide/narrow knobs to the wide setting.

You must adjust both of the knobs to the same position.

For wide supplies, push down and turn the wide/narrow knobs clockwise with a screwdriver.

For narrow supplies, turn the wide/narrow knobs counter-clockwise with a screwdriver until it pops back up.

The adjustment is shown in the wide position.

Loading Supplies 2-13

Image 27

Contents Monarch 9800 Series Printers Canadian D.O.C. Warning B L E O F C O N T E N T S Checking Script Information Page Page Main Menu T T I N G S T a R T E DP a c k i n g t h e P r i n t e r D i e n c eT a b l i s h i n g C o m m u n i c a t i o n s N n e c t i n g t h e P o w e r C a b l eI n g t h e C o n t r o l P a n e l N n e c t i n g t h e C o m m u n i c a t i o n C a b l eI n t e r S t a t u s L i g h t s Enter/Pause S p l a yMain Menu L e c t i n g a F u n c t i o nI t i n g a n O p t i o n 8Getting Started A D I N G S U P P L I E S A d i n g L a b e l s o r Ta g s Supply Holder Guides Die Cut Sensor Nibs Supply Lever Thumb Well 6Loading Supplies Feed the backing paper over the peel bar I n g t h e O p t i o n a l Te a r B a r D i n g t h e P e e l E d g e o r S h e l f I n g L i n e r l e s s S u p p l yPage If inserting the peel bar Page J u s t i n g t h e W i d e / N a r r o w K n o b s 14Loading Supplies A D I N G R I B B O N A d i n g R i b b o n Take-up Core Take-up Reel Ribbon Rollers 4Loading Ribbon T T I N G S U P P L Y O P T I O N S Supply P p l y Ty p eRibbon B b o nSpeed E e dFeed Mode E d M o d eC k f e e d S i t i o n i n g I n t P o s i t i o nBackfeed Positioning P p l y P o s i t i o n R g i n P o s i t i o n Positioning Separators T c h S e p a r a t o r sSkip Index I p I n d eT t i n g C o n t r a s t 14Setting Supply Options M M U N I C AT I O N V a L U E S Baud Rate U d R a t eWo r d L e n g t h Serial CommO p B i t s R i t yStopbits O w C o n t r o l ParityFlow Control R a l l e l C o m m u n i c a t i o n s S e t t o D e Fault Va l u e sPort Parallel CommUSA T T I N G D E Fault SUSA N e t a r y S i g nDefaults C o n d a r y S i g nMonetary Sign C i m a l P l a c e s Secondary SignDecimal Places Slashed Zero A s h e d Z e r oW e r U p M o d e Power UP ModePrompt SET O m p t S e t8Setting Defaults I t i a l S c r i p t S t a r t u p P r o c e d u r e s I N G S C R I P T SMystore E c k i n g S c r i p t I n f o r m a t i o nR m a t t i n g F l a s h M e m o r y ScriptsSetup Flash MemoryCreating Flash File System W n l o a d i n g a S c r i p t A b l i n g a S c r i p t L e t i n g a S c r i p t E w i n g S c r i p t I n f o r m a t i o nA b l i n g I m m e d i a t e C o m m a n d s A b l i n g S t a t u s P o l l i n gE c k i n g a v a i l a b l e F l a s h M e m o r y Print Mode I N T I N GI n t i n g D e m a n d M o d e P r i n t i n g I n t i n g a n Error L a b e lU s i n g a B a t c h S t a r t i n g a B a t c hPause Menu N c e l i n g a P a u s e d B a t c h To cancel only the paused batch, press l or r until you see P e a t i n g a B a t c h I n t i n g Tr u e Ty p e F o n t s SL5 OPY C e n s i n g Yo u r F o n t sR E a N D M a I N T E N a N C E E a r i n g L a b e l J a m sE a n i n g Voids Printhead P l a c i n g t h e P r i n t h e a d Page Snap the printhead into place E c k i n g t h e S o f t w a r e Ve r s i o n DiagnosticsI N G D I a G N O S T I C S C t o r y S e t P a s s w o r dUser Diag I n t i n g a Te s t L a b e lE c k i n g S u p p l y Q u a l i t y I n g P a s s w o r d P r o t e c t i o n R v i c e D i a g n o s t i c s Tr o u b l e s h o o t i n g This section helps you correct some problems that may occurError M e s s a g e s Error Description/Action M m o n Error sPage Page I n t e r Specification SP p l i e s B b o n Specification N e r l e s s S u p p l i e sO u t R i b b o n s B l e P i n o u t s C e s s o r i e s C E S S O R I E S & O P T I O N SH e r n e t I n f o r m a t i o n C t o r y Install e d O p t i o n sFormat O S S a R YPage Index D EFlow control options 5 Function, selecting 1 Start XO N character Index