Paxar 9856 manual M o v i n g a R i b b o n

Page 16

7.Pull the ribbon over the ribbon rollers. Wrap the free end of the ribbon around the ribbon take-up hub. Slide the J-hook into place. Hold the ribbon take-up hub and rotate the J-hook clockwise to latch it.

J-hook

Take-up Hub

Ribbon

8.Rotate the hub until you remove all slack from the ribbon. Do not use the J-hook to rotate the hub.

9.Close the printhead latch, rotate the latch wing clockwise, and lower the latch wing.

10.Close the side access cover.

R e m o v i n g a R i b b o n

1.Cut the ribbon in between the ribbon rollers.

2.Rotate the ribbon supply hub clockwise to draw the unused portion of the ribbon back onto the supply hub.

3.Rotate the ribbon take-up hub counterclockwise to roll up the used portion of the ribbon, and slide the used ribbon off the hub.

4.Hold the ribbon take-up hub and rotate the J-hook counterclockwise to unlatch it. Slide off the used portion of the ribbon.

2-4 Loading Supplies

Image 16

Contents Monarch Printer Canadian D.O.C. Warning B L E O F C O N T E N T S Specifications T T I N G S T a R T E D D i e n c eN n e c t i n g t h e P o w e r C a b l e T a b l i s h i n g C o m m u n i c a t i o n sI n g t h e C o n t r o l P a n e l T t o n s a n d L i g h t s I n g t h e K e y p a d I n g t h e M a i n M e n uL e c t i n g a F u n c t i o n Main MenuI t i n g a n O p t i o n SetupSupply Getting Started A D I N G S U P P L I E S A d i n g N o n P e e l a n d F a n F o l d S u p p l yLoading Supplies A d i n g a R i b b o n M o v i n g a R i b b o n Tear Bar Installation Thumbscrew Retainer T T I N G S U P P L Y O P T I O N S T c h S e p a r a t o r s B b o nRibbon Separators E d M o d eSupply Type I n t P o s i t i o n P p l y P o s i t i o n R g i n P o s i t i o n Print too far to the left Print too far to the rightT P o s i t i o n P p l y T y p eE e d SpeedM M U N I C AT I O N V a L U E S U d R a t e R d L e n g t hBaud Rate User CommO p B i t s R i t yStopbits ParityO w C o n t r o l S e t t o D e Fault V a l u e sFlow Control T T I N G C O N T R a S T Setup r Press E. Press L or R until you see T T I N G D E Fault S USAN e t a r y S i g n Country Currency DescriptionC o n d a r y S i g n DefaultsMonetary Sign C i m a l P l a c e s A s h e d Z e r oSecondary Sign Decimal PlacesW e r U p M o d e Power UPSlashed Zero O m p t S e t Prompt SETR E a N D M a I N T E N a N C E E a n i n g t h e P r i n t h e a dJ u s t i n g t h e S u p p l y S e n s o r J u s t i n g t h e S u p p l y W i d t h Care and Maintenance Diagnostics A G N O S T I C SC t o r y S e t P a s s w o r d E c k i n g t h e S o f t w a r e V e r s i o nR v i c e D i a g n o s t i c s I n t i n g T e s t L a b e l sUser Diag Troubleshooting Problem Description/ActionM m o n Error s Error Description/ActionTroubleshooting Troubleshooting E C I F I C AT I O N S I n t e rRibbon Widths