Paxar 9856 manual O w C o n t r o l, S e t t o D e Fault V a l u e s, Flow Control

Page 30

F l o w C o n t r o l

To change the setting, from the Main Menu, select Setup, Port Settings, then User Comm. Then, follow these steps.

1.Press L or R until you see

USER COMM

lFlow Control r

2.Press E. You will see the current setting, for example:

FLOW CONTROL

l DTR r

The XON character is 17; XOFF is 19. Set flow control to DTR for PC computers (unless you have XON/XOFF software).

3.Press L or R to display the flow control you need, press E. Press U three times to exit to the Main menu.

R e s e t t o D e f a u l t V a l u e s

To change the setting, from the Main Menu, select Setup, Port Settings, then User Comm. Then, follow these steps.

1.Press R until you see

USER COMM

lReset

2.Press E. You will see

Are you sure?

No r

3.Press L or R to make your selection, press E. Press U three times to exit to the Main Menu.

4-4 Communication Values

Image 30

Contents Monarch Printer Canadian D.O.C. Warning B L E O F C O N T E N T S Specifications T T I N G S T a R T E D D i e n c eN n e c t i n g t h e P o w e r C a b l e T a b l i s h i n g C o m m u n i c a t i o n sI n g t h e C o n t r o l P a n e l T t o n s a n d L i g h t s I n g t h e K e y p a d I n g t h e M a i n M e n uL e c t i n g a F u n c t i o n Main MenuSetup I t i n g a n O p t i o nSupply Getting Started A D I N G S U P P L I E S A d i n g N o n P e e l a n d F a n F o l d S u p p l yLoading Supplies A d i n g a R i b b o n M o v i n g a R i b b o n Tear Bar Installation Thumbscrew Retainer T T I N G S U P P L Y O P T I O N S B b o n T c h S e p a r a t o r sRibbon E d M o d e SeparatorsSupply Type I n t P o s i t i o n P p l y P o s i t i o n R g i n P o s i t i o n Print too far to the left Print too far to the rightT P o s i t i o n P p l y T y p eE e d SpeedM M U N I C AT I O N V a L U E S Baud Rate U d R a t eR d L e n g t h User CommStopbits O p B i t sR i t y ParityS e t t o D e Fault V a l u e s O w C o n t r o lFlow Control T T I N G C O N T R a S T Setup r Press E. Press L or R until you see T T I N G D E Fault S USAN e t a r y S i g n Country Currency DescriptionDefaults C o n d a r y S i g nMonetary Sign Secondary Sign C i m a l P l a c e sA s h e d Z e r o Decimal PlacesPower UP W e r U p M o d eSlashed Zero O m p t S e t Prompt SETR E a N D M a I N T E N a N C E E a n i n g t h e P r i n t h e a dJ u s t i n g t h e S u p p l y S e n s o r J u s t i n g t h e S u p p l y W i d t h Care and Maintenance C t o r y S e t P a s s w o r d DiagnosticsA G N O S T I C S E c k i n g t h e S o f t w a r e V e r s i o nI n t i n g T e s t L a b e l s R v i c e D i a g n o s t i c sUser Diag Troubleshooting Problem Description/ActionM m o n Error s Error Description/ActionTroubleshooting Troubleshooting E C I F I C AT I O N S I n t e rRibbon Widths