RuggedCom RX1510 DDS Rx and Tx LED Indications, SFP Optics Installation, removal, and precautions

Page 28

3. Installation

3.10. DDS Rx and Tx LED Indications

The DDS module features Rx and Tx LED indicators that display transmit and receive status.

Figure 3.22. DDS Module Rx and Tx LED Indicators

The following tables describe the DDS module Rx and Tx LED status indications:

Rx LED Color

Status

GREEN

Frame sync detected and signal OK.

 

 

YELLOW

Signal OK, but no frame sync.

 

 

RED

Loss of signal.

 

 

OFF

The interface is not enabled.

 

 

Table 3.7. DDS Rx LED Indications

Tx LED Color

Status

GREEN

The interface is enabled and remote device has no errors.

 

 

YELLOW

The interface is in loopback mode.

 

 

RED

Loss of signal or receiving any of OOS, UNM, or UMC codes: the remote device is out of service

or has problems with the signal.

 

 

 

OFF

The interface is not enabled.

 

 

Table 3.8. DDS Tx LED Indications

3.11. SFP Optics – Installation, removal, and precautions

The RX1510 can be ordered with SFP (Small Form-factor Pluggable) pluggable optics modules. SFP modules can be safely inserted and removed while the chassis is powered and operating. When inserting or removing optics, observe the following precautions:

Ensure that dust caps are mounted on SFP cages at all times, unless you are in the process of inserting or removing an SFP module. The dust caps prevent the accumulation of residue or particles that might inhibit proper operation.

Ensure that you have properly discharged any possible electrostatic build-up to prevent electrostatic discharges (ESD). This can be accomplished by proper grounding through an ESD wrist strap, or by touching earth or chassis ground before installing or removing optical modules. ESD can damage or shorten the life of optical modules when they are not plugged into a chassis.

Ensure that SFP optical modules are always stored in an ESD-safe bag or other suitable ESD-safe environment. Keep SFP modules free from moisture and store them at the proper temperature (-40°C to +85°C).

Disconnect all cables from the SFP module before inserting or removing the module.

Use only components certified by RuggedCom Inc. with RuggedCom products. Damage can occur to optics and product if compatibility and reliability have not been properly assessed.

RuggedCom® RuggedBackbone™

28

RX1510 Installation Guide Rev 104

Image 28
Contents RuggedBackbone RX1510 Warranty Contacting RuggedCom All Rights ReservedDisclaimer Of Liability Registered TrademarksTable of Contents Page List of Figures Page List of Tables FCC Statement And Cautions Product Overview Feature HighlightsFunctional Overview WAN RuggedBackbone Modules LM1 through LM4Front Panel Module Status LEDsPurpose Description Green = OK LM 1 through Orange = Warning alertEthernet Copper Line Modules LMEthernet Fiber SFP Modular WANSerial Cellular ModemDDS Digital Data Services APE Appplication Processing EnginePower Supply 27. Pluggable terminal block power module HIP module shownInstallation Mounting1. RX1510Dimensions DIN Rail Mounting Side ViewRX1510Dimensions Top View Connectors for HI and HIP Power Modules Power Supply Wiring and GroundingConnectors for 24, 24P, 48, and 48P Power Modules AC Power Supply Wiring Chassis Ground ConnectionDC Power Supply Wiring Examples AC and DC Power Supply Wiring ExampleCritical Alarm Wiring 15. Critical Alarm Relay ConnectorRJ45 Pin Signal Function Serial Console PortWAN Ports RJ45 T1/E1 pinoutWAN Ports BNC Copper Ethernet Ports1. RJ45 Twisted-Pair Copper Ports Gigabit Ethernet 1000Base-TX Cabling RecommendationsTransient Suppression Cabling Category 1000Base Required ActionPin RS232 Mode RS485 Mode RS422 Mode Serial Ports RJ45DDS Ports RJ45 RJ45 Pin DescriptionSFP Optics Installation, removal, and precautions DDS Rx and Tx LED IndicationsRx LED Color Status Tx LED Color StatusModule Insertion SFP SFP Module RemovalFiber Ethernet Ports 25. SFP module removalCellular Modems Module Order Code DescriptionInstalling SIM Cards for GSM, EDGE, HSPA+ Cellular Modems GSM, EDGE, HSPA+ Cellular Modem CardPage Feature Description APE Application Processing EngineAPE Overview Supported Operating SystemsSecondary Network Interface Placing the APE in a VlanInstalling an Operating System Procedure 3.1. To install an operating systemAPE Bios Resetting the ModuleLED Indicators LED Color and StateFAQs Technical Specifications Power Supply SpecificationsCritical Alarm Relay Specifications Copper Ethernet Port SpecificationsFiber Ethernet Port Specifications Fast Ethernet 100Mbps Optical SpecificationsCable Tx λ typ Tx min Tx max Distance Power OrderGigabit Ethernet 1Gbps Optical Specifications Mechanical SpecificationsOperating Environment EMI And Environmental Type Tests Test Description Test Levels SeverityIeee 1613 C37.90.x EMI Immunity Type Testsa Test Description Test LevelsAgency Approvals Agency Standards CommentsWarranty RuggedCom Inc