3Com 2226 PLUS manual Spanning Tree Screen

Page 50

50CHAPTER 4: CONFIGURING THE SWITCH

path is maintained between spanning tree-compliant networked devices by:

■Disabling redundant paths when the main paths are operational.

■Enabling redundant paths if the main paths fail.

Spanning tree uses a distributed algorithm to select a bridging device that serves as the root of the spanning tree network. The bridging device, known as the Root Bridge, generates bridge protocol data units (BPDUs) on all ports at a regular interval known as the Hello Time. All other spanning tree-compliant devices on the network have a designated Root Port. This is the Port nearest the Root Bridge and it is used for receiving the BPDUs initiated by the Root Bridge. If a bridge does not get a Hello BPDU after a predetermined interval, the bridge assumes that the link to the Root Bridge is down. This bridge will then initiate negotiations with other bridges to reconfigure the network to reestablish a valid network topology.

After all the bridges on the network have determined the configuration of their ports,

each bridge only forwards traffic between the Root Port and the ports that are the Designated Bridge Ports for each network segment. All other ports are blocked, which means that they are prevented from forwarding traffic.

To use spanning tree, choose enabled from the drop State down menu, fill in the setup parameters, and click Apply.

Figure 33 Spanning Tree Screen

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Baseline Switch Plus 3C16475CS3Com Corporation 350 Campus Drive Marlborough MA USA Contents Snmp Glossary Regulatory Notices Index Page About this Guide ConventionsDocumentation Comments Product RegistrationAutosensing of MDI/MDIX Connections Overview of the Baseline SwitchFeatures and Capabilities Autonegotiating 10/100 Mbps PortsPhysical Features Front PanelGigabit Combo Ports RJ-45/SFP 10/100BASE-TX Ports Power LED Rear PanelPackage Contents Positioning the Switch Before You BeginUsing the Mounting Kit Rack-Mounting or Free-StandingMontagesatz Anweisungen Placing Units On Top of Each OtherSupplying Power to the Switch Checking for Correct OperationInserting an SFP Transceiver Using SFP TranceiversApproved SFP Transceivers Removing an SFP Transceiver Inserting an SFP TransceiverPerforming Spot Checks Installing the Switch Requirements for Accessing the Web Interface Running the Discovery ApplicationWelcome screen of Discovery appears Logging On to the Web Interface Discovered Devices ScreenNavigating the Web Interface MenuLists the available items on the menu Menu Item Description Buttons Port StatusManually Assigned Static IP Address Accessing the Interface Without Using DiscoveryDhcp Assigned IP Address Configuration Overview Device Summary InformationDevice View Polling IntervalAutomatic IP Configuration Administration SettingsModifying the IP Address Settings Color KeyIP Setup To set the IP address for the SwitchBackup Configuration Restore ConfigurationFirmware Upgrade Upgrade ScreenReboot InitializeSystem Access User SummaryCreate User Modify UserSystem Time Remove UserSnmp Add SetupSummary Configuring VLANs Snmp RemoveVlan Modify Vlan Modify PortRename Modify Port ScreenVlan Detail RemovePort Detail Sample Vlan Configurations Forwarding Tagged/Untagged FramesSetting Up Two VLANs on the Same Switch Setting Up Vlan Across Two SwitchesTagged Vlan Configuration Spanning TreeSpanning Tree Screen Broadcast Storm Igmp SnoopingIgmp Query Broadcast Storm Setup Screen Configuring Port Settings AdministrationPort Administration Detail Screen DetailPort Administration Setup Screen Speed/Duplex for 1000 Mbps ConnectionsLink Aggregation Guidelines for Creating TrunksCreate ModifySpanning Tree per Port Link Aggregation Remove ScreenSpanning Tree Summary Screen Spanning Tree Detail Screen Port Mirroring Setup Screen Port MirroringQoS VoIP Traffic Settings StatisticsPort Setup QoS VoIP Summary ScreenQoS Port Setup Screen OUI SummaryOUI Modify SecurityRadius Client Configure Radius Client Detail Screen802.1X Settings Radius Client Configure Screen802.1X Summary Screen Security Address Table Cable DiagnosticsMonitoring Diagnostics Cable Diagnostic Summary ScreenConfiguring the Switch Troubleshooting Resetting to Factory DefaultsForgotten Static IP Address Forgotten PasswordSolving LED Issues Fiber cable is connected, but the Module Active LED is off Link/Activity LED is on, but network performance is poorIf the Problem Persists All ports appear to show continual activityRegister Your Product Purchase Value-Added ServicesTroubleshoot Online Access Software Downloads Telephone Technical Support and Repair Contact UsCountry Telephone Number Latsupportanc@3com.com Physical Related StandardsEnvironmental ElectricalAppendix B Technical Information Safety Information Important Safety InformationAppendix C Safety Information Bandwidth 1000BASE-TAuto-negotiation Category 5e Cables Category 3 CablesCategory 5 Cables Category 6 CablesIeee 802.1D Full DuplexHalf Duplex Ieee 802.1QMAC Address LayerLink Aggregation NetworkSubnet Address SwitchServer Subnet MaskVlan Regulatory Notices Page Index NumbersIndex

2226 PLUS specifications

The 3Com 2226 PLUS is a robust network switch designed to meet the increasing demands of modern networking environments. Its ability to provide reliable connectivity and support for various technologies makes it an ideal choice for small to medium-sized businesses. This switch features 24 10/100 Mbps Ethernet ports, which allow for fast and efficient data transfer, enabling businesses to enhance their network performance significantly.

One of the standout technologies employed in the 3Com 2226 PLUS is its support for auto-negotiation. This feature automatically detects the speed and duplex capabilities of connected devices, ensuring optimal performance and minimizing configuration errors. This capability simplifies network management, allowing IT professionals to focus on other critical tasks rather than troubleshooting connectivity issues.

In addition to its impressive port offerings, the 3Com 2226 PLUS incorporates a range of Layer 2 switching features. These include support for Virtual LANs (VLANs), which enable businesses to segment their networks for improved security and efficiency. By implementing VLANs, organizations can isolate sensitive data traffic from less secure networks, enhancing overall data protection.

The switch also supports Spanning Tree Protocol (STP), which helps prevent loops in network topology. This is crucial in environments with multiple switches, as it maintains a stable network while ensuring redundancy. If a primary link fails, STP allows for a backup path to be automatically activated, ensuring minimal disruption in connectivity.

Power over Ethernet (PoE) capabilities are another significant feature of the 3Com 2226 PLUS. This technology allows the switch to deliver power to connected devices, such as IP cameras and VoIP phones, eliminating the need for additional power supplies and reducing cable clutter.

In terms of management, the 3Com 2226 PLUS supports both simple web-based configuration and SNMP (Simple Network Management Protocol), providing network administrators with flexibility in how they manage their network infrastructure.

Built with reliability in mind, the switch comes equipped with features like store-and-forward switching, error checking, and a sturdy design suitable for deployment in various environments.

Overall, the 3Com 2226 PLUS combines essential features and advanced networking technologies, making it a versatile and dependable solution for businesses looking to upgrade or establish their network infrastructure.
Top Page Image Contents