3Com 2226 PLUS manual Spanning Tree Summary Screen

Page 59

used for receiving the BPDUs initiated by the Root Bridge. If a bridge does not get a Hello BPDU after a predetermined interval, the bridge assumes that the link to the Root Bridge is down. This bridge will then initiate negotiations with other bridges to reconfigure the network to re-establish a valid network topology.

After all the bridges on the network have determined the configuration of their ports, each bridge only forwards traffic between the Root Port and the ports that are the Designated Bridge Ports for each network segment. All other ports are blocked, which means that they are prevented from forwarding traffic.

Three tabs are available on the Spanning Tree per Port page:

■Summary

■Detail

■Setup

Configuring Port Settings

59

Summary

Use the Summary tab to display Status, Edged Port, Link Type, Path Cost, State, or Port Priority for all the ports.

Figure 44 Spanning Tree Summary Screen

Page 58 Page 60
Image 59
Page 58 Page 60
Contents 3C16475CS Baseline Switch Plus3Com Corporation 350 Campus Drive Marlborough MA USA Contents Snmp Glossary Regulatory Notices Index Page Conventions About this GuideProduct Registration Documentation CommentsAutonegotiating 10/100 Mbps Ports Overview of the Baseline SwitchFeatures and Capabilities Autosensing of MDI/MDIX ConnectionsFront Panel Physical FeaturesGigabit Combo Ports RJ-45/SFP 10/100BASE-TX Ports Rear Panel Power LEDPackage Contents Before You Begin Positioning the SwitchRack-Mounting or Free-Standing Using the Mounting KitPlacing Units On Top of Each Other Montagesatz AnweisungenChecking for Correct Operation Supplying Power to the SwitchInserting an SFP Transceiver Using SFP TranceiversApproved SFP Transceivers Inserting an SFP Transceiver Removing an SFP TransceiverPerforming Spot Checks Installing the Switch Running the Discovery Application Requirements for Accessing the Web InterfaceWelcome screen of Discovery appears Discovered Devices Screen Logging On to the Web InterfaceMenu Navigating the Web InterfaceLists the available items on the menu Menu Item Description Port Status ButtonsManually Assigned Static IP Address Accessing the Interface Without Using DiscoveryDhcp Assigned IP Address Device Summary Information Configuration OverviewPolling Interval Device ViewColor Key Administration SettingsModifying the IP Address Settings Automatic IP ConfigurationTo set the IP address for the Switch IP SetupRestore Configuration Backup ConfigurationUpgrade Screen Firmware UpgradeInitialize RebootUser Summary System AccessModify User Create UserRemove User System TimeSnmp Add SetupSummary Snmp Remove Configuring VLANsVlan Modify Port Modify VlanModify Port Screen RenameVlan Detail RemovePort Detail Forwarding Tagged/Untagged Frames Sample Vlan ConfigurationsSetting Up Vlan Across Two Switches Setting Up Two VLANs on the Same SwitchSpanning Tree Tagged Vlan ConfigurationSpanning Tree Screen Broadcast Storm Igmp SnoopingIgmp Query Broadcast Storm Setup Screen Administration Configuring Port SettingsDetail Port Administration Detail ScreenSpeed/Duplex for 1000 Mbps Connections Port Administration Setup ScreenGuidelines for Creating Trunks Link AggregationModify CreateLink Aggregation Remove Screen Spanning Tree per PortSpanning Tree Summary Screen Spanning Tree Detail Screen Port Mirroring Port Mirroring Setup ScreenStatistics QoS VoIP Traffic SettingsQoS VoIP Summary Screen Port SetupOUI Summary QoS Port Setup ScreenOUI Modify SecurityRadius Client Radius Client Detail Screen ConfigureRadius Client Configure Screen 802.1X Settings802.1X Summary Screen Security Address Table Cable DiagnosticsMonitoring Cable Diagnostic Summary Screen DiagnosticsConfiguring the Switch Resetting to Factory Defaults TroubleshootingForgotten Static IP Address Forgotten PasswordSolving LED Issues Link/Activity LED is on, but network performance is poor Fiber cable is connected, but the Module Active LED is offAll ports appear to show continual activity If the Problem PersistsRegister Your Product Purchase Value-Added ServicesTroubleshoot Online Access Software Downloads Contact Us Telephone Technical Support and RepairCountry Telephone Number Latsupportanc@3com.com Electrical Related StandardsEnvironmental PhysicalAppendix B Technical Information Important Safety Information Safety InformationAppendix C Safety Information Bandwidth 1000BASE-TAuto-negotiation Category 6 Cables Category 3 CablesCategory 5 Cables Category 5e CablesIeee 802.1Q Full DuplexHalf Duplex Ieee 802.1DNetwork LayerLink Aggregation MAC AddressSubnet Mask SwitchServer Subnet AddressVlan Regulatory Notices Page Numbers IndexIndex

2226 PLUS specifications

The 3Com 2226 PLUS is a robust network switch designed to meet the increasing demands of modern networking environments. Its ability to provide reliable connectivity and support for various technologies makes it an ideal choice for small to medium-sized businesses. This switch features 24 10/100 Mbps Ethernet ports, which allow for fast and efficient data transfer, enabling businesses to enhance their network performance significantly.

One of the standout technologies employed in the 3Com 2226 PLUS is its support for auto-negotiation. This feature automatically detects the speed and duplex capabilities of connected devices, ensuring optimal performance and minimizing configuration errors. This capability simplifies network management, allowing IT professionals to focus on other critical tasks rather than troubleshooting connectivity issues.

In addition to its impressive port offerings, the 3Com 2226 PLUS incorporates a range of Layer 2 switching features. These include support for Virtual LANs (VLANs), which enable businesses to segment their networks for improved security and efficiency. By implementing VLANs, organizations can isolate sensitive data traffic from less secure networks, enhancing overall data protection.

The switch also supports Spanning Tree Protocol (STP), which helps prevent loops in network topology. This is crucial in environments with multiple switches, as it maintains a stable network while ensuring redundancy. If a primary link fails, STP allows for a backup path to be automatically activated, ensuring minimal disruption in connectivity.

Power over Ethernet (PoE) capabilities are another significant feature of the 3Com 2226 PLUS. This technology allows the switch to deliver power to connected devices, such as IP cameras and VoIP phones, eliminating the need for additional power supplies and reducing cable clutter.

In terms of management, the 3Com 2226 PLUS supports both simple web-based configuration and SNMP (Simple Network Management Protocol), providing network administrators with flexibility in how they manage their network infrastructure.

Built with reliability in mind, the switch comes equipped with features like store-and-forward switching, error checking, and a sturdy design suitable for deployment in various environments.

Overall, the 3Com 2226 PLUS combines essential features and advanced networking technologies, making it a versatile and dependable solution for businesses looking to upgrade or establish their network infrastructure.
Top Page Image Contents