3Com 8807, 8814, 8810 manual Main Menu

Page 87

	Upgrading the Software 87
Board self testing
The board is steady
SlotNo of this board is 6
The MCX is exist
BootRom main system CRC check is OK
82559 register testing is OK
EPLD1 testing is OK
EPLD2 testing is OK
16c2552 register testing is OK
Please check LEDs	LED testing finished
The switch Mac address is 00e0.fc00.1111
Press Ctrl+B to enter Boot Menu...	5
Password :

1Press <Ctrl+B> as prompted to display the system Password : prompt.

n To enter the Boot menu, you must press <Ctrl+B> within five seconds after the appearance of the “Press Ctrl-B to enter Boot menu...” prompt. Otherwise, the program decompression process begins. To access the Boot menu after the switch enters the program decompression process, you need to restart the switch.

2Enter the Boot ROM password (the switch’s default is no password). The Boot menu displays as follows:

c CAUTION: Make sure you have Boot ROM password.

MAIN MENU

1.Boot with default mode

2.Boot from Flash

3.Boot from HardDisk

4.Enter serial submenu

5.Enter ethernet submenu

6.Modify Flash description area

7.Modify bootrom password

0. Reboot

Enter your choice(0-7):

3Ensure that the upgraded host program is compatible with the existing I/O module’s Boot ROM program. Otherwise, you must upgrade it during a host program upgrade.

4When loading the host program through the Boot menu, configure the serial interface’s attributes as shown in Figure 62. Otherwise, the Hyper Terminal does not respond.

Image 87

Contents 3Com Switch 8800 Family United States Government Legend 3Com Corporation Campus Drive Marlborough, MA USAContents Examining Installation Site Installation Tools Switch InstallationLists text conventions that are used throughout this guide ConventionsProtocols that are used to interconnect LANs Lists icon conventions that are used throughout this guideAbout this Document SwitchRelated Documentation8800s Preface3Com Switch 8810 10-Slot Chassis 3Com Switch 8814 14-Slot Chassis Switch 8807 slots Chassis and Slots SwitchSwitch 8810 slots Switch FunctionsStructure AC Power System Specifications SwitchEach Ethernet port can deliver up to 15.4 W to its PD PoE entry area External PoE Power Rack 3C17509Mbus Introduction Normal AbnormalLabel Color State Abnormal reason Role and function Fan tray panel of the Switch 8800 FamilyGbps Switch Fabric Fabric ModulesPanel Status LEDs for the management 10Base-T/100Base-TX port RS232/485 port specificationsCompact Flash CF slot Management PortsStatus LEDs Reset buttonConsole port specifications AUX port specificationsStatus LEDs for I/O module Status LEDs for the 360 Gbps Switch Fabric moduleGbps Switch Fabric LED Status CF status LED720 Gbps Switch Fabric specifications Gbps Switch Fabric Technical specificationsAUX port Status LEDs for the 720 Gbps Switch Fabric module Technical specifications of the Switch 8800 Family Status LEDs for the 720 Gbps Switch Fabric moduleSoftware Features Supported software featuresSoftware features of the Switch 8800 Family Lacp Software features of the Switch 8800 Family Product Overview 3C17511 1-port 10GBASE-X Xenpak O modules available to the Switch 8800 Family3C17511 module specifications OverviewPort LEDs on the 3C17511 module 3C17512 module specifications3C17512 2-port 10GBASE-X XFP Module Panel and LEDs 3C17511 module panelSpecifications 3C17513 12-port 1000BASE-X SFP ModulePanel and LEDs Figure 3C17513 module has two LEDs for each port on its panel 3C17514 24-port 1000BASE-X SFP Module3C17525 1-port 10GBASE-X Advanced Xenpak Module 3C17516 24-port10/100/1000BASE-T ModulePort LEDs on the 3C17525 module 3C17526 module specifications3C17526 4-port 10GBASE-X XFP Module Panel and LEDs 3C17525 module panel1000 Mbps optical port LEDs on the 3C17526 module 3C17527 module specifications3C17527 2-port 10GBASE-X XFP Advanced Module 3C17526 module panel3C17528 module has one LED for each port on its panel 3C17528 48port 10/100/1000 BASE-T RJ-45 Module3C17530 24-port 1000BASE-X SFP Advanced Module 3C17531 24-port 10/100/1000BASE-T Advanced ModulePanel and LEDs 3C17530 module panel Port LEDs on the 3C17531 module 3C17532 module specifications3C17531 module has one LED for each port on its panel Panel and LEDs 3C17531 module panel3C17533 24-port 1000BASE-X SFP IPv6 Module 3C17532 module has one LED for each port on their panelPanel and LEDs 3C17533 module panel 3C17536 4-port 10GBASE-X XFP Quad IPv6 Module 3C17534 module specifications3C17536 module specifications 3C17534 24-port 10/100/1000BASE-T IPv6 Module1000 Mbps optical port LEDs on the 3C17536 module 3C17537 module specifications3C17537 2-port 10GBASE-X XFP IPv6 Module Panel and LEDs 3C17536 module panel1000 Mbps optical port LEDs on the 3C17537 module 3C17538 module specifications3C17538 48-port 1000BASE-X SFP IPv6 Module Panel and LEDs 3C17537 module panelFront panel Technical specifications for the 3C17542Status LEDs on the 3C17546 Technical specifications for the 3C17546Technical specifications for the 3CR1754766 Available cablesStatus LEDs on the 3CR1754766 Technical specifications for the 3C17548Documents the 3Com Switch 8800 Family transceivers Transceiver SpecificationsTransceivers Switch 8800 Port Switch 8800 Available ModulesDensities O and Application Modules Recommendations SafetyGeneral Safety RecommendationsInstallation Preparation Gas Average mg/m3 Max. mg/m3 Limitation on dust content in equipment roomMechanical active material Unit Content Harmful gas limits in an equipment roomMeasure Installation ToolsPower Supply Requirements Space Requirements Required installation toolsInstallation Flow Confirming Installation PreparationOne Switch 8807 chassis in a cabinet Mounting the Switch User-Supplied CabinetOne Switch 8807 chassis in a cabinet Switch 8807 11U Two Switch 8807 chassis in a cabinetTwo Switch 8807 chassis in a cabinet Switch 8807 11U One Switch 8810 chassis in a cabinetOne Switch 8810 chassis in a cabinet Switch 8810 14U One Switch 8814 chassis in a cabinetCabinet One Switch 8814 chassis in a cabinet Switch 8814 17UConnecting Pgnd Wire and Power Cord Connecting Pgnd Wire Common grounding environmentOther grounding environment Ground the switch when ground bar is available Ground the switch via AC PE wire Connecting AC Power CordConnect AC power cord to the Switch Grounding PoE chassis Connecting PoE power cableInstalling Fan Tray Install mounting ears onto the both sides of the switchFan tray is hot swappable Contact take the fan tray out from the packing bag Lightning Protection BoxFasten the screw on top of the PoE lightning protection box Installing I/O modulesIntroduction Connecting Interface CablesConnecting console cable RJ-45 Signal Direction DB-25 DB-9AUX cable pinouts AUX cableConnecting Fiber Connecting AUX cableIntroduction to RJ-45 connector Connecting category-5 shielded cableCable Routing Recommendations Cable ManagementIntertwinement or bending is allowed Cable bundling example Cable fixing example Cable bundle diameter mm Space between bundles mm Verifying InstallationInstallation checking list Tie-binding parametersSwitch Installation Environment Setting upConfiguration Connecting the CablesVerifying Installation Before Powering Switch Powering and Booting the SwitchZbbtest Debugging the System LEDs on the PSU Troubleshooting the PSUFail LED red is on Check that Display Power Command Indicates the PSU is Not in PositionIndicator State description Input LED green and Output LED green are OFFRemoving an AC PSU Hardware MaintenanceIndicator Replacing AC PSURemoving and cleaning the air filter of PSU Installing an AC PSUReplacing and Cleaning Chassis’s Air Filter Installing the air filter of PSU Removing a Module Removing and Cleaning the Chassis’s Air Filter Installing the Chassis’s Air Filter Required toolsInstalling a Module Replacing the Fan Tray Required toolsReplacing the Fan Tray Upgrading SoftwareRequired cables Main Menu Serial Submenu Please Select File Xmodem downloading ...CCC This procedure uses a Switch 8814 work as the Tftp client Tftp and to 0x0 if you are using FTP This procedure uses a Switch 8814 work as the FTP client Using FTP Port using FTPLoad host program Using FTPProgram Boot ROM and host program loading process is now completeUsing Tftp Configuration did not save during the I/O module rebootPassword Loss Insufficient Flash memoryRepresentative Switch Monitoring and Maintenance Lightning Arrester PowerInstalling a Lightning Arrester for Network Port Installation procedureUse the nylon ties to bundle the cables neatly Installation diagram of a network port’s lightning arrester Installation precautionsChapter a Lightning Protection of the Switch Supervisor 3Com NetworkDirector Access ManagerApplication such as 3Com Enterprise Management Suite EMS HP OpenViewNetwork Node ManagerAppendix B 3COM Network Management

Related manuals

Manual 97 pages 32.87 Kb