3Com 2900 manual 5Description of the FTP parameters

Page 58

Table 5-5Description of the FTP parameters

 

Item

 

Description

 

 

Load File Name

:

Name of the file to be downloaded

 

 

 

 

 

 

 

Server IP Address

:

IP address of the PC

 

 

 

 

 

 

 

Local IP Address

:

IP address of the switch

 

 

 

 

 

 

Gateway IP Address :

IP address of the gateway

 

 

 

 

 

 

 

FTP User Name

 

Username for logging in to the FTP server, which should be consistent

 

 

 

with that configured on the FTP server.

 

 

 

 

 

 

 

 

 

 

 

FTP User Password

Password for logging in to the FTP server, which should be consistent

 

 

with that configured on the FTP server.

 

 

 

 

 

 

 

 

 

 

z

z

Enter the file name and IP addresses based on the actual condition.

If the switch and the server are on the same network segment, you can specify any unused IP address of the network for the switch without specifying the gateway’s IP address; if they are not on the same segment, you need to specify the gateway’s IP address so that the switch can communicate with the server.

6)Update the Boot ROM file on the switch

Enter the corresponding parameters based on the actual condition. The system displays the following information:

Will you Update Basic BootRom? (Y/N):Y

The system asks you whether you want to update the basic Boot ROM section. Click Y. The system displays the following information after the update is complete:

Updating Basic BootRom

Done!

Updating extended BootRom? (Y/N):Y

The system asks you whether you want to update the extended Boot ROM section. Click Y and then the system displays the following information after the update is complete:

Updating extended BootRom

Done!

7)Restart the switch to make the updated Boot ROM file effective Press any key to return to the Boot ROM update menu.

Press enter key when ready

1.Update full BootRom

2.Update extended BootRom

3.Update basic BootRom

0.Return to boot menu Enter your choice(0-3):

Enter 0 to return to the Boot ROM menu, and then enter 0 again. After that, the device is restarted and the updated Boot ROM file becomes effective.

5-16

Page 57 Page 59
Image 58
Page 57 Page 59
Contents
3Com Baseline Switch 2900 Family Environmental Statement Organization About This ManualConventions Obtaining Documentation Related DocumentationManual Description Table of Contents Page Product Overview IntroductionPage Front Panel 3Com Baseline Switch 2920-SFP PlusPower Supply System Rear Panel3Com Baseline Switch 2928-SFP Plus 3Com Baseline Switch 2952-SFP Plus 3Com Baseline Switch 2928-PWR Plus 3Com Baseline Switch 2928-HPWR Plus Console Port SpecificationPorts 10/100/1000Base-T Ethernet PortFiber Transceiver Central Connector Type1000Base-X SFP Interface Max Transmis Sion DistanceLEDs Power LEDRPS Status LED Port Ethernet port status Switch model Mode Meaning Port Mode LED10/100/1000Base-T Auto-Sensing Ethernet Port Status LED LED 1000Base-X SFP Interface Status LED Installation Site Installation PreparationsSafety Precautions Temperature/HumidityDust concentration limit in the equipment room Laser SafetyElectromagnetic Susceptibility Gas Maximum concentration mg/mInstallation Tools Introduction to Mounting Brackets Installing a SwitchModel Mounting bracket Description Attaching the Mounting Brackets to a Switch Model Mounting position Description See -6 , FigureMounting the Switch to a Rack Page Connecting the Pgnd Cable Mounting the Switch on a WorkbenchWhen a Grounding Strip is Available Page Other Installation Sites Where a Grounding Conductor Can be BuriedWhen the switch is AC-powered Connecting the Power Cord Connecting an AC Power CordVerifying the Installation Connecting an RPS DC Power CordPage Connecting the Console Cable Initial Power-OnSetting Up the Configuration Environment RJ-45 Signal Direction DB-9Setting Terminal Parameters Connection Procedure4Set the serial port used by the HyperTerminal connection 6HyperTerminal window Checking Before Power-On Booting the SwitchPowering On the Switch Describes the fields above 2Description on the fields Changing the Boot Mode Enter 9. The system prompts you to change the startup modeEnter Y. The system displays the following information User interface aux0 is available Press Enter to get started Loading Files Through the Boot ROM Menu Approaches for Loading Application and Configuration FilesLoading Software Introduction to the Boot ROM Menu Loading a Boot ROM file Loading Files Using Xmodem Through Console PortIntroduction to Xmodem Task Remarks Change the rate of the serial port on the terminalDescription Page 2Properties dialog box 5Transfer menu Restoring the download rate to the default Page Loading Files Using Tftp Through Ethernet Port Introductin to TftpLoad File Name Loading an application file Loading Files Using FTP Through Ethernet Port Introduction to FTPParameters are described in Table 5Description of the FTP parameters Loading an application file User Password Loss Maintenance and TroubleshootingPassword Loss Boot ROM Password LossWith RPS power input Power Supply FailureWith AC power input With both AC and RPS power suppliesTroubleshooting when there is no terminal display Configuration Terminal FailureTroubleshooting when the terminal display is illegible
Top Page Image Contents