Connect Power Source, Programming, Service

Connect Power Source:

If powered by Power Supply: Plug power supply into source.

If powered by Operator: Connect wires to the proper operator accessory supply source (10 V AC/DC to 28 V AC/DC source).

1.Re-connect power to the door or gate operator.

2.Using wall control, activate door or gate operator to conﬁ rm power connection.

6(continued)

To Erase All Learned Transmitters:

1.Press and hold down the PROGRAM button.

2.After 10 seconds, the red STATUS LED will blink 5 times indicating all transmitters are erased from the receiver’s memory.

3.Release the PROGRAM button.

4.Re-learn transmitters as needed following the above Programming instructions.

Trouble-Shooting:

Symptom	Possible Solution
1. Receiver’s red STATUS	Check power source to receiver. Insure
LED does not turn on	proper 10 VAC/DC minimum to 28 VAC/
when programming button	DC maximum power source.
pressed.
2. No transmitter range	Check antenna connections and, if in-
(less than 10 ft).	stalled, check antenna extension kit coax
	wire for damage or kinks. Correct antenna
	connection or replace coax as needed.
3. Poor transmitter range	Insure antenna is not near any metal. Re-
(less than 50 ft).	position antenna from vertical to horizontal
	position or vice versa. Possible near-by
	radio interference.
4. With transmitter	Check relay (RLY) wire connections. In-
activation, the receiver’s	sure relay wire is not broken or damaged.
STATUS LED lights and	Insure relay wire is connected to proper
a ”click” is heard within	terminals on operator. Using insulated
receiver, but receiver does	pliers or insulated screwdriver, short RLY

RADIO RECEIVER

LIMITED WARRANTY

THE MANUFACTURER (WAYNE-DALTON CORP.) WARRANTS ALL COMPONENTS OF THE RADIO RECEIVER MODEL 3990-372, 3994-433 FOR A PERIOD OF 90 DAYS FROM THE TIME OF INSTALLATION AGAINST DEFECTS IN MATERIALS AND WORKMANSHIP, PROVIDED IT IS PROPERLY INSTALLED, USED, MAINTAINED AND SERVICED UNDER NORMAL USE AND SERVICE.

THE ABOVE CONDITIONS APPLY PROVIDED THAT THE ABOVE REFERENCED RADIO RECEIVER MODEL 3990-372, 3994-433 IS PROPERLY INSTALLED, USED, MAINTAINED, AND SERVICED IN ACCORDANCE WITH THE MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS UNDER NORMAL USE AND SERVICE.

THIS LIMITED WARRANTY EXTENDS ONLY TO THE ORIGINAL PURCHASER, PROVIDED THE ABOVE REFERENCED RADIO RECEIVER IS PROPERLY INSTALLED, USED, MAINTAINED, AND SERVICED. THIS LIMITED WARRANTY IS NOT TRANSFERABLE.

NO EMPLOYEE, DISTRIBUTOR, OR REPRESENTATIVE IS AUTHORIZED TO CHANGE THE FOREGOING WARRANTIES IN ANY WAY OR GRANT ANY OTHER WARRANTY ON BEHALF OF MANUFACTURER.

THE MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY DAMAGE RESULTING TO OR CAUSED BY ITS PRODUCTS BY REASON OF INSTALLATION, IMPROPER STORAGE, UNAUTHORIZED SERVICE, ALTERATION OF PRODUCTS, NEGLECT OR ABUSE, ANY ACTS OF NATURE BEYOND MANUFACTURER’S CONTROL (SUCH AS, BUT NOT LIMITED TO, LIGHT- NING, POWER SURGES, WATER DAMAGE, ETC.), OR ATTEMPT TO USE THE PRODUCTS FOR OTHER THAN THE CUSTOMARY USAGE OR FOR THEIR INTENDED PURPOSES. THE ABOVE

Programming:

WARNING: Keep away from all high-voltage contacts while servicing receivers.

WARNING: During programming, door or gate operator will acti- vate. Keep people and objects away from door or gate.

1. Test receiver by operating a

compatible RF transmitter. The

Receiver’s STATUS LED will

ﬂ ash indicating reception.

PROGRAM BUTTON

Safe Operation Precautions

WARNING: To reduce the risk of severe or fatal injury.

1.Always keep a moving door or gate in sight and keep people and objects away until it is completely opened or closed.

2.No one should cross the path of a moving door or gate.

3.Never let children operate or play with the controls. Keep all controls away from children.

4.Never go under a stopped, partially open door. Never walk through a vehicular entry gate; always use the pedestrian entry.

5.Keep ﬁ ngers and other body parts away from the all moving parts of the door, gate and operator system while the system is being operated.

6.Periodically test the safety systems of the door or gate. Disconnect and do not use this receiver if any of your door or gate’s safety systems fail their tests. Then have door or gate operator serviced immediately.

7.SAVE THESE INSTRUCTIONS.

not activate operator.	terminals on receiver and this should
	activate operator. Test operator for proper
	operation.
5. Can not learn transmit-	Insure transmitter is a correct transmitter
ter.	for this receiver. Check this receiver’s RF
	frequency and the companion transmitter’s
	frequency to insure they are identical. Test
	receiver with another transmitter.

WARRANTY DOES NOT COVER NORMAL WEAR OR ANY DAMAGE BEYOND MANUFACTUR- ER’S CONTROL OR REPLACEMENT LABOR.

CLAIMS FOR DEFECTS IN MATERIAL AND WORKMANSHIP COVERED BY THIS WARRANTY SHALL BE MADE IN WRITING, WITHIN THE WARRANTY PERIOD, TO THE DEALER TO WHOM THE PRODUCT WAS PURCHASED. MANUFACTURER MAY EITHER SEND A SERVICE REPRE- SENTATIVE OR HAVE THE PRODUCT RETURNED TO THE MANUFACTURER AT BUYER’S EX- PENSE FOR INSPECTION. IF JUDGED BY MANUFACTURER TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP, THE PRODUCT WILL BE REPLACED OR REPAIRED AT THE OPTION OF THE MANUFACTURER, FREE FROM ALL CHARGES EXCEPT AUTHORIZED TRANSPORTATION AND REPLACMENT LABOR.

THE REMEDIES OF BUYER SET FORTH HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER REMEDIES, THE LIABILITY OF MANUFACTURER, WHETHER IN CONTACT, TORT, UNDER ANY WARRANTY OR OTHERWISE, SHALL NOT EXTEND BEYOND ITS OBLIGATION TO REPAIR OR REPLACE, AT ITS OPTION, ANY PRODUCT OR PART FOUND BY MANUFACTURER TO BE DEFECTIVE IN MATERIAL OR WORK. MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY DIRECT, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM STATE TO STATE. HOWEVER, SOME STATES DO NOT ALLOW LIMI- TATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLU- SIONS MAY NOT APPLY TO YOU.

2. Press and release the

receiver’s PROGRAM button

once. The receiver’s red

STATUS LED will turn on and

remain on for 25 seconds,

indicating that the receiver is

ready to learn a transmitter.

3. Press the button on the

transmitter you wish to use to

control the operator. The

receiver’s red STATUS LED

will turn on and off three times

indicating a successful learn.

4. Press the same button on the

transmitter once more to conﬁ rm

operation of the door or gate

operator.

5. Test range of transmitter.

Repositioning antenna may

provide greater range.

6. Repeat Transmitter

Programming steps for

additional transmitters.

RED STATUS LED

Operation:

Whenever this receiver senses a valid signal from a learned transmitter, the relay will activate for one second and, therefore, activate the operator.

1.Press and release selected button on Wayne Dalton transmitter.

2.Receiver LED will light and the unit will cycle.

Maintenance:

Disconnect electric power to door or gate operator before making repairs or removing case covers. While this receiver is maintenance-free, periodic cleaning of the receiver case is suggested. To clean the receiver case, disconnect power to receiver and operator and then use a soft cloth to remove any dirt and dust.

Service:

Unit contains no user serviceable parts. Contact your dealer or Wayne-Dalton customer support for additional information.

To Remove This Receiver From Service:

1.Disconnect power to operator (door operator, gate operator, etc.) and disconnect power to this receiver.

2.Disconnect all wiring connected to receiver. Disconnect antenna and any associated coax wiring.

3.Remove receiver from mounting location. Discard properly per local codes.

4.Reconnect power to operator. Test operator for proper operation.

FCC and IC Statement

FCC Regulatory Information:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IC Regulatory Information:

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communication; however, there is no guarantee that interference will not occur in a particular installa- tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning equipment off and on, user is encouraged to try to correct interference by one or more of the following measures:

Reorient or relocate receiving antenna. Increase separation between equipment and receiver. Connect equipment into an outlet on a circuit different from that which receiver is connected. Consult your dealer or/and experienced radio/television technician for help.

WARNING: Changes or modiﬁ cations to this unit not expressly approved by party responsible for compliance could void user’s authority to operate this equipment.

Questions?

STOP

Need Information?

Call Us Toll-Free:

(888) 827-3667

Thank you for your purchase

www.waynedalton.com

Please Do Not Return This Product To The Store

Call Us Directly! Our Trained Technicians Will Answer Your Questions and /or Ship Any Parts You May Need.

You can reach us Toll Free 1-888-827-3667 for Consumer Assistance or online at www. wayne-dalton.com

Wayne-Dalton 3994-433 Connect Power Source, Trouble-Shooting Symptom Possible Solution, Operation