Peavey GTX GTx Stereo Input Module, Gain & R Gain Controls, Three-Band Sweep Equalizer Controls

GTX CENTURY SERIES

STEREO
	—
		+48V
		LINE
		PAD
	40	GAIN
30
		50
20		70
80		150
40		300
20		400
		HPF
		Ø
	INSERT
–	O	+
8		8
HF 16		16
8K		12K
6K
4K		16K
–	O	+
8		8
MF 16		16
400
250		1
300		8K
–	O	+
8		8
16		16
LF
150		300
100		6
40		1K
		EQ IN
4	5	6	1
			2
3		7
2		8
1		9
0		10
4	5	6	3
			4
3		7

2		8
1		9
0		10
4	5	6	3
			4
3		7
2		8
1		9
0		10
		PRE
		PRE
4	5	6	5
3		7
2		8
1		9
0		10
4	5	6	6
3		7
2		8
1		9
0		10
4	5	6	7
3		7
2		8
1		9
0		10
4	5	6	8
3		7
2		8
1		9
0		10

PRE

STEREO

AUX SENDS

BAL

WIDTH

MUTE

M

P

LRA N

1 2

3 4

5 6

7 8

PFL

PK +8 0

-6 10

GTx Stereo Input Module

The GTx Stereo Input module is essentially two GTx Input modules packaged to fit into a one-module space. This mod- ule is very useful for accepting remote feeds, effects outputs and other signals that require stereo handling.

48V Phantom Power Switch

Applies 48 Volts DC to pins 2 & 3 of the both L and R XLR inputs, for microphones requiring phantom power.

LINE Switch

Switches between the balanced XLR Microphone Input con- nector and the balanced Line Input 1/4" TRS connector for both L and R channels.

PAD Switch

Introduces a -20 dB attenuation to the mic input signal for both L and R XLR inputs.

L GAIN & R GAIN Controls

These concentric controls adjust input gain for proper signal level for both Left and Right inputs. Maximum gain is 70 dB. Inner knob is for L GAIN, outer knob is for R GAIN.

Adjustable High Pass Filter

For both Left and Right inputs, reduces all low frequency content at a -12db per octave rate adjustable from 20 to 400 Hz (-3dB point). Yellow LED illuminates when switch is down.

Polarity Reverse Switch

For both input channels, inverts the polarity of both the microphone and line inputs. An internal jumper selects between Left channel only (default) or both Left & Right channels. When this switch is pushed, an associated LED lights.

INSERT Switch

Switches signal processor in and out of L and R signal paths. Associated green LED is illuminated when switch is down.

Three-Band Sweep Equalizer Controls

2		8
1		9
0		10
		PRE
		PRE
4	5	6	5
3		7
2		8
1		9
0		10
4	5	6	6
3		7
2		8
1		9
0		10

SIG

SAFE

5

0

5

10

15

The equalization controls in this module act upon both L and R stereo channels at once. All three EQ bands are set up as sweep EQ’s: the upper knob controls the gain or cut (15 dB); while the lower knob controls the center frequency adjusted by the inner knob. Center frequencies are indicated around the lower knob.

EQ IN Switch

Inserts the EQ section into both L and R input channel sig- nals at once. An associated green LED illuminates when the switch is down.

	4	5	6	7
3				7
2				8
1				9
0			10
4		5	6	8
3				7
2				8
1				9
0			10
			PRE
		STEREO
AUX SENDS
				BAL

SCENE

MUTE 20 SELECT

A - D

30

AUX Level 1&2 / 3&4

Adjusts signal level sent to respective Aux buses. The signal source for this mix may be selected pre or post fader by an associated switch. The left channel is sent to the odd-num- bered Auxes, and the right channel is sent to the even-num- bered Auxes.

PAGE 12