TDK iQP 5V/50A manual Absolute Maximum Ratings, Input Characteristics

Page 4

Data Sheet: PoweretaTM iQP Series –Single Output Quarter Brick

Absolute Maximum Ratings:

Stress in excess of Absolute Maximum Ratings may cause permanent damage to the device.

 

Characteristic

Min

 

Max

 

 

Unit

Notes & Conditions

 

Continuous Input Voltage

-0.5

 

80

 

 

Vdc

 

 

 

 

 

 

 

 

 

 

 

 

Transient Input Voltage

---

 

100

 

 

Vdc

100mS max.

 

 

 

 

 

 

 

 

 

 

 

Isolation Voltage

 

 

 

 

 

 

 

 

Input to Output

---

 

1500

 

 

Vdc

Basic Insulation

 

Input to Base-plate

---

 

1500

 

 

Vdc

Basic Insulation

 

Output to Base-plate

---

 

500

 

 

Vdc

Operational Insulation

 

 

 

 

 

 

 

 

 

 

 

Storage Temperature

-55

 

125

 

 

˚C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Measured at the location specified in the thermal

 

Operating Temperature Range (Tc)

 

-40

 

119

 

 

˚C

measurement figure. Maximum temperature varies

 

 

 

 

 

with model number, output current, and module

 

 

 

 

 

 

 

 

 

orientation – see curve in thermal performance

 

 

 

 

 

 

 

 

 

section of the data sheet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input Characteristics:

Unless otherwise specified, specifications apply over all Rated Input Voltage, Resistive Load, and Temperature conditions.

Characteristic

 

Min

Typ

Max

Unit

Notes & Conditions

Operating Input Voltage

 

36

48

75

Vdc

 

Maximum Input Current

50A output

---

---

8.5

A

Vin = 0 to Vin,max, Io=Io,max, Vo=Vo,nom

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Turn-on Voltage

 

---

34.7

---

Vdc

 

Turn-off Voltage

 

---

32.3

---

Vdc

 

 

 

 

 

 

 

 

Hysteresis

 

---

2.4

---

Vdc

 

 

 

 

 

 

 

Startup Delay Time from application of input

---

3

---

mS

Vo = 0 to 0.1*Vo,nom; on/off =on,

voltage

 

 

 

 

 

Io=Io,max, Tc=25˚C

Startup Delay Time from on/off

 

---

3

---

mS

Vo = 0 to 0.1*Vo,nom; Vin = Vi,nom,

 

 

 

 

 

 

Io=Io,max,Tc=25˚C

Output Voltage Rise Time

 

---

25.5

---

mS

Io=Io,max,Tc=25˚C, Vo=0.1 to 0.9*Vo,nom

 

 

 

 

 

 

 

Inrush Transient

 

---

---

0.1

A2s

Exclude external input capacitors

Input Reflected Ripple

 

---

35

---

mApp

See input/output ripple and noise

 

 

 

 

 

 

measurements figure; BW = 20 MHz

Input Ripple Rejection

 

---

65

---

dB

@120Hz

 

 

 

 

 

 

 

* Engineering Estimate

Caution: The power modules are not internally fused. An external input line normal blow fuse with a maximum value of 15A is required; see the Safety Considerations section of the data sheet.

©2005-2006 TDK Innoveta Inc.

(877) 498-0099

4/15

iQP 5V/50A Datasheet 8/3/2006

 

Image 4
Contents Standard Features Optional FeaturesOption Table Ordering informationProduct Offering Mechanical Specification Pin AssignmentInput Characteristics Absolute Maximum RatingsElectrical Data IQP48050A050V-000 through -0x9 5V, 50A, 250W OutputElectrical Characteristics Trim Trim Up Down Change Resistor Vout Ohm Thermal measurement location Thermal PerformanceIQP48050A050V-000 through -009 5V, 50A, 250W Output Wind Tunnel Test Setup Figure Thermal Management10/15 Operating Information = 5.11⋅ Circuit to increase output voltage ReliabilityInput/Output Ripple and Noise Measurements Quality Lin Vin Vout Cext RLoad Ground PlaneSafety Considerations Warranty