Quantum LTO-2 manual Index

Page 92

Index

considerations 32 intelligent 33

data compression 31 Data integrity 29

error-correction code 29 servo-tracking faults 31 DEC/Compaq Unix settings 50

Desktop drives

checking SCSI termination 17 connecting a power cable 17 connecting a SCSI cable 16 installation instructions 16 installing the LTO driver 17 quick start 5

SCSI ID settings 16 Drive maintenance

cleaning a tape drive 24 Drive performance specifications

Specifications

drive performance 39

E

Ejecting a cartridge 71 Emergency cartridge eject 71 Emergency reset 71 Environmental requirements 41 Error-correction code 29 External drives

quick start 5

F

Features 2

Front panel display 20

G

Guidelines, internal drives 6

H

HP-UX 11.0 settings 61

I

IBM AIX 4.1.x and later settings 54 Injected noise 42

Inspection 6 Installation instructions

see desktop drives 16 see internal drives 7

Installing the LTO driver desktop drives 17 internal drives 15

Intelligent data compression 33 Internal drives

checking SCSI termination 14 configuring 7

connecting a power cable 15 connecting a SCSI cable 13 connecting a serial cable 14 guidelines and cautions 6 installation instructions 7 installing the LTO drive 15 mounting 11

quick start 4 registering 15

SCSI ID 8 terminator power 10

78	LTO-2 Half-Height Tape Drive User’s Guide

Image 92

Contents 72 Copyright Statement Contents Chapter Operation Mean Time to Replace Safety Compliance EMC ComplianceInjected Noise Reliability Chapter Troubleshooting Guide Figures Figures Viii Tables Tables Preface Audience Purpose Document OrganizationTech Tip NotationalConventions SCSI-2 Specification RelatedDocuments ContactsCustomer Support Send faxes for the Customer Support Department toSend e-mail for the Customer Support Department to Visit our web site1Introduction Features 2Installation and Quick Start Drive Quick Start Quick Start GuideInternal LTO-2 Half-Height Tape Desktop LTO-2 Unpacking and Inspection Internal Tape Drive Guidelines and CautionsDrive Installation Instructions Installing an Internal LTO-2 Half-Height Tape DriveJumper Pins Scsi IDScsi ID=8 Jumpers Open Shunted DefaultTerminator Power Within 5 degrees of horizontal MountingHorizontally or vertically see figure Internal LTO Half-Height Tape Drive Mounting Dimensions Rear View Internal LTO-2 Half-Height Tape Drive Connecting a Checking the Scsi TerminationSerial Cable for Tape LibrariesConnecting a Power Installing the LTO DriverPin Numbers Description CableInstalling a Desktop LTO-2 Half-Height Tape Drive Cord Desktop LTO-2 Half-Height Tape DriveLTO-2 Half-Height Tape Drive User’s Guide 3Operation Understanding the Front Panel Display Generic Front Panel DisplayBlink Codes EOTUsing LTO Cartridges Loading a Cartridge Unloading a CartridgeWrite-protecting a CartridgeMaintenance Cartridge CareDrive Maintenance Retensioning the TapeOperation Drive Maintenance Operation Drive Maintenance 4Theory Track LayoutShows the layout of data on an LTO tape Data Integrity Recording MethodData Buffer C1 ECC Faults Data CompressionServo-tracking Tracking is re-establishedData Compression Considerations Intelligent Data CompressionPage 5Specifications Physical Specifications Internal Scsi Drive Specification Without Bezel With BezelInternal LTO-2 Half-Height Tape Drive Dimensions Idle Power Watts RMS Standby Power Typical Operating Power Power SpecificationsSpecification +12 VDC + 5VDC Drive Performance Specifications Specification LTO-2Specification Value Specification Operational Non-operational Environmental RequirementsAt any frequency between 45 Hz and 20 MHz ReliabilityInjected Noise Specification Description Mean Time Between FailuresLTO Cartridge Specifications Mean Time toReplace Environmental ConsiderationsReliability Regulatory ComplianceCartridge Memory Country Regulatory Organization Compliant to EMC Compliance Country Regulatory Organization Compliant to Disposal of Electrical and Electronic Equipment 6UNIX Settings Configuring for the DEC/Compaq Unix Environment Word About Scsi ControllersSave the file. Then run the following command ParametersFinding Current TargetsTypes ControllersSt.conf ConfiguringDevice File Smit Enter Smit at the Tape Drive menu by typing smit tape Set the Block size toConfiguring for SCO Open Server Using the commandThis command produces output similar to Current tape drives can be found using the commandConfiguring the LTO-2 Half-Height Tape Drive with mkdev Configuring for Linux Finding Existing Scsi Controllers DevicesYou should see output similar to To find existing Scsi devices execute the commandYou may see output similar to Output of the command will be similar to the following Configuring for SGI IrixScsi controllers and devices use the command Hardware/Driver Configuring for HP-UXConfiguration Unix Settings Configuring for HP-UX 7Troubleshooting Guide Installation Best PracticesClicking on Computer Management Device Manager Troubleshooting Suggestions Troubleshooting Guide Troubleshooting Suggestions Windows Operating System Red Hat LinuxProblems with Tape Drive and Cartridge Tape will not Load into Tape DriveTape will not Eject from the Drive LTO-2 Half-Height Tape Drive User’s Guide Emergency Reset and Emergency Cartridge Eject Problems During Backup/Restore OperationsPreviously Written Data on the Tape will be Destroyed Tape is Write Protected Miscellaneous TapeAlert Messages If either of the following messages appearsLTO-2 Half-Height Tape Drive User’s Guide Slow Backups LTO-2 Half-Height Tape Drive User’s Guide Index Index Scsi ID Tape drive