Chapter 2: Installation
Memory Support for the motherboards w/5500 Series Processors
installed
RDIMM Population for the Motherboard w/5500 Processors Installed
DIMM | DIMMs | DIMM Type (Reg.= | Speeds (in MHz) | Ranks per DIMM |
Slots per | Populated | Registered) |
| (any combination; |
Channel | per Channel |
|
| SR=Single Rank, |
|
|
|
| DR=Dual Rank, |
|
|
|
| QR=Quad Rank) |
2 | 1 | Reg. DDR3 ECC | 800,1066,1333 | SR or DR |
2 | 1 | Reg. DDR3 ECC | 800,1066 | QR |
2 | 2 | Reg. DDR3 ECC | 800,1066 | Mixing SR, DR |
2 | 2 | Reg. DDR3 ECC | 800 | Mixing SR, DR, QR |
UDIMM Population for the Motherboard w/5500 Processors Installed
DIMM | DIMMs | DIMM Type | Speeds (in | Ranks per DIMM |
Slots per | Populated | (Unb.= Unbuffered) | MHz) | (Mixing: any |
Channel | per Channel |
|
| combination; |
|
|
|
| SR=Single Rank, |
|
|
|
| DR=Dual Rank) |
2 | 1 | Unb. | 800,1066,1333 | SR or DR |
2 | 2 | Unb. | 800,1066 | Mixing SR, DR |
Memory Support for the Motherboards w/5600 Processors Installed
•1.5V DIMMs
1.5V RDIMM Population for the Motherboard w/5600 Processors Installed
DIMM | DIMMs | DIMM Type | Speeds (in MHz) | Ranks per DIMM |
Slots per | Populated | (Reg.=Registered) |
| (any combination; |
Channel | per Channel |
|
| SR=Single Rank, |
|
|
|
| DR=Dual Rank, |
|
|
|
| QR=Quad Rank) |
2 | 1 | Reg. DDR3 ECC | 800,1066,1333 | SR or DR |
2 | 1 | Reg. DDR3 ECC | 800,1066 (Note 1) | QR |
2 | 2 | Reg. DDR3 ECC | 800,1066, 1333 | Mixing SR, DR |
2 | 2 | Reg. DDR3 ECC | 800 (Note 2) | Mixing SR, DR, QR |
Note 1: 1333 MHz RDIMMs will run at 1066 MHz
Note 2: 1333/1066 MHz RDIMMs will run at 800 MHz
1.5V UDIMM Population for the Motherboard w/5600 Processors Installed
DIMM | DIMMs | DIMM Type (Unb.= | Speeds (in MHz) | Ranks per DIMM |
Slots per | Populated | Unbufered) |
| (any combination; |
Channel | per Channel |
|
| SR=Single Rank, |
|
|
|
| DR=Dual Rank, |
|
|
|
| QR=Quad Rank) |
2 | 1 | Unb. DDR3 | 800,1066,1333 | SR or DR |
2 | 2 | Unb. DDR3 | 800,1066, 1333 | Mixing SR, DR |
Note 1: 1333 MHz for two DIMMs per channel is supported when Unbuf./ECC DIMMs are used.
Note 2: Mixing of 1.35V and 1.5V DIMMs is not recommended.