SUPER MICRO Computer X6DH8-G2, X6DHE-G2 manual Table of Contents

Page 4

X6DH8-G2/X6DHE-G2 User's Manual

 

Table of Contents

 

Preface

 

About This Manual

iii

Manual Organization

iii

Chapter 1: Introduction

 

1-1

Overview

1-1

 

Checklist

1-1

 

Contacting Supermicro

1-2

 

X6DH8-G2/X6DHE-G2 Image

1-3

 

X6DH8-G2/X6DHE-G2 Layout

1-4

 

Quick Reference

1-5

 

Motherboard Features

1-6

 

Intel Lindenhurst Chipset: System Block Diagram

1-8

1-2

Chipset Overview

1-9

1-3

Special Features

1-10

 

Recovery from AC Power Loss

1-10

1-4

PC Health Monitoring

1-10

1-5

ACPI Features

1-11

1-6

Power Supply

1-13

1-7

Super I/O

1-13

Chapter 2: Installation

 

2-1

Static-Sensitive Devices

2-1

 

Precautions

2-1

 

Unpacking

2-1

2-2 PGA Processor and Heatsink Installation

2-2

2-3

Installing DIMMs

2-6

2-4 I/O Ports/Control Panel Connectors

2-7

2-5

Connecting Cables

2-9

 

ATX Power Connector

2-9

 

Processor Power Connector

2-9

 

NMI Button

2-10

 

Power LED

2-10

 

HDD LED

2-11

 

NIC1 LED

2-11

 

Overheat LED

2-12

 

Power Fail LED

2-12

 

Reset Button

2-13

iv

Image 4
Contents Super Page About This Manual Manual OrganizationTable of Contents Troubleshooting Bios AppendicesChecklist OverviewContacting Supermicro HeadquartersEurope Asia-PacificX6DH8-G2/X6DHE-G2 Image X6DH8-G2/X6DHE-G2 Motherboard Layout X6DH8-G2Connector Description Jumper Description Default SettingQuick Reference X6DH8-G2/X6DHE-G2 Motherboard Features M o r yChipset Expansion SlotsAcpi Features DimensionsOnboard I/O OtherBlock Diagram of the E7520 Lindenhurst Chipset Chipset Overview Special Features Recovery from AC Power LossEnvironmental Temperature Control PC Health MonitoringAcpi Features CPU Fan Auto-Off in Sleep ModeCPU Overheat LED and Control System Resource AlertSlow Blinking LED for Suspend-State Indicator Main Switch Override MechanismMicrosoft OnNow External Modem Ring-OnPower Supply Super I/OPage Static-Sensitive Devices PrecautionsUnpacking Nocona Processor and Heatsink Installation CPU InstallationCEK Heatsink Installation To Un-install the Heatsink PGA604 Socket Empty and with Processor Installed Mounting the Motherboard in the ChassisDimm Installation See Figure Installing DIMMsMemory Support I/OPorts/Control Panel Connectors I/O Port Locations and DefinitionsJF1 Header Pins Front Control PanelATX Power Connector Connecting CablesProcessor Power Connector Power LED NMI ButtonNIC1/NIC2 LED Indicators HDD LEDPower Fail LED Overheat LED OHReset Button Power ButtonChassis Intrusion Universal Serial Bus USB0/1Front Panel Universal Serial Bus Headers Serial PortsGlan Giga-bit Ethernet Ports ATX PS/2 Keyboard and PS/2 Mouse PortsPower LED/Speaker Fan HeadersWake-On-Ring Wake-On-LANConnector SMB Power I2 CGlan Enable/Disable Jumper SettingsExplanation Jumpers Cmos Clear Watch DogVGA Enable/Disable Alarm ResetPower Fault Power FaultScsi Enable/Disable *ForX6DH8 only Scsi CH A/B Termination Enable/Disable *ForX6DH8 onlyGlan LEDs Onboard IndicatorsOverheat LED JOH1 Parallel Port, Floppy/Hard Disk Drive and Scsi Connections Parallel Printer PortFloppy Connector IDE ConnectorsUltra320 Scsi Connectors X6DH8-G2 Only Pin Ultra320 Scsi Connectors JA1 and JA2Troubleshooting Procedures Before Power OnNo Power Or installing any hardware componentsMemory Errors Technical Support ProceduresLosing the System’s Setup Configuration Frequently Asked Questions Question How do I update my BIOS?Returning Merchandise for Service Question Whats on the CD that came with my motherboard?System Bios How To Change the Configuration DataStarting the Setup Utility IntroductionMain Bios Setup Running SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup FeaturesNative Mode Operation Serial ATA RAID EnableSerial ATA LBA Mode Control TypeMulti-Sector Transfer Bit I/OAdvanced Setup Transfer ModeUltra DMA Mode System MemoryBoot Features Quick Boot ModeQuiet Boot Acpi ModeMemory Cache Cache System Bios Area Cache Video Bios AreaCache Base 0-512K Cache Base 512K-640KPCI Configuration Onboard Glan Gigabit- LAN Oprom ConfigureOnboard Scsi Oprom Configure Default Primary Video AdapterPCI Parity Error Forwarding Reset Configuration DataEnable Master Latency TimerLarge Disk Access Mode Force Compliance ModeClock Spectrum Feature Dram Data Integrity ModeSerr Signal Condition Enabling Multi-Media TimerUSB Function Legacy USB SupportNo Execute Mode Memory Protection *Available when supported Processor Power ManagementThermal Management 2 *Available when supported by the CPU Adjacent Cache Line Prefetch *Available when supported byDevice Configuration Serial Port aBase I/O Address InterruptDMA Channel Floppy Disk ControllerDMI Event Logging Event Log ValidityConsole Redirection COM Port AddressBaud Rate Console TypeHardware Monitor Logic CPU Temperature Threshold Fan Speed Control ModesSupervisor Password Is User Password IsSet Supervisor Password Set User PasswordFixed Disk Boot Sector Password on BootBoot +Removable DevicesCdrom Drive +Hard DriveLoad Setup Defaults ExitExit Saving Changes Exit Discarding ChangesSave Changes Terminal Post Errors Recoverable Post ErrorsPost Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Introduction to the Intel ICH5R I/O Controller Hub Combined Mode ATA Operate ModeEnhanced Mode Appendix B Software Installation Instructions Using the Adaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACUManaging Arrays From the ARC menu, select Array Configuration Utility ACU Viewing Array PropertiesDeleting Arrays RAID 1 only-the following prompt is also displayedCreating Arrays To create an arrayAssigning Array Properties Raid Level Create Via When Appropriate When you are finished, press Done as the screen shown below Adding a Bootable Array Deleting a Bootable ArrayAdding/Deleting Hotspares Initializing Disk Drives To initialize drivesPage Page Rebuilding Arrays To Rebuild an arrayUsing the Disk Utilities To access the disk utilitiesPage To Exit Adaptec RAID Configuration Utility You can choose from the following optionsInstalling Intels ICH5R Driver by Adaptec and the OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control