SUPER MICRO Computer X7DBi+ user manual Exit

Page 83

Chapter 4: BIOS

4-7 Exit

Choose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys. You should see the following display. All Exit BIOS settings are described in this section.

Exit Saving Changes

Highlight this item and hit <Enter> to save any changes you have made and to exit the BIOS Setup utility.

Exit Discarding Changes

Highlight this item and hit <Enter> to exit the BIOS Setup utility without saving any changes you may have made.

Load Setup Defaults

Highlight this item and hit <Enter> to load the default settings for all items in the BIOS Setup. These are the safest settings to use.

Discard Changes

Highlight this item and hit <Enter> to discard (cancel) any changes you have made. You will remain in the Setup utility.

Save Changes

Highlight this item and hit <Enter> to save any changes you have made. You will remain in the Setup utility.

4-27

Image 83
Contents Super Manual Revision Release Date June 25 Preface About This ManualManual Organization Conventions Used in the ManualTable of Contents Table of Contents Security Setup Boot Setup Exit Main Bios SetupIntroduction ChecklistOverview Headquarters Contacting SupermicroX7DBi+ Image Not drawn to scale X7DBi+ Motherboard LayoutQuick Reference X7DBi+ Jumper Description Default SettingPC Health Monitoring MemoryChipset Expansion SlotsOther Acpi FeaturesDimensions Onboard I/O5000P Block Diagram of the 5000P ChipsetXeon Quad Core Processors Chipset OverviewXeon Dual Core Processors PC Health Monitoring Special FeaturesExternal Modem Ring-On Acpi FeaturesSlow Blinking LED for Suspend-State Indicator Main Switch Override MechanismSuper I/O Power SupplyPage Page Unpacking PrecautionsInstallation Static-Sensitive DevicesInstallation of the LGA771 Processor Processor and Heatsink InstallationPage CEK Heatsink Installation Installation of the HeatsinkTo Un-install the Heatsink Mounting the Motherboard in the Chassis Dimm Module Population Configuration Installing DIMMsDimm Installation Memory SupportInstalling and Removing DIMMs Back Panel Connectors/IO Ports Control Panel Connectors/IO PortsFront Control Panel JF1 Header PinsPower Button NMI Button Pin Definitions JF1 Power LEDPower LED Pin Definitions JF1 Front Control Panel Pin Definitions NMI ButtonPin# Definition Vcc 10/12 Ground NIC1/NIC2 LED IndicatorsPin# Definition 13 +5V HD Active PWR Supply Fail Power Fail LEDOverheat/Fan Fail LED OH OH/Fan Fail LEDReset Button Pin Definitions JF1 Reset ButtonPower Button Reset Button B. PWR ButtonProcessor Power Connector Connecting CablesATX Power Connector Front Panel USB Universal Serial Bus USBChassis Intrusion Backpanel USBFan Header Pin Definitions Fan1-8 Fan HeadersKeylock Fan Fan 7 CPU Fan Fan 8 CPU FanPin 10 is available on COM2 only. NC No Connection COM1 is a connector located onATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortsWake-On-LAN Pin Definitions WOL Wake-On-RingWake-On-LAN Wake-On-Ring Pin Definitions WORPWR LED/Speaker Power LED/SpeakerSpeaker Connector Glan 1/2 Giga-bit Ethernet PortsAlarm Reset Power Fault PWR Supply FailureAlarm Reset Power Fault B. Alarm ResetPin# Definition Data Ground Clock No Connection SMBus PS I2C ConnectorSMB J18 PWR SMB J17 SMB Header Pin DefinitionsLocation VGA ConnectorSgpio Headers There are two T-SGPIO Serial GeneralCompact Flash PWR Compact Flash Card PWR ConnectorCompact Flash Card PWR Connector Jumper Definition Compact Flash Power On Off Power OffExplanation Jumpers Jumper SettingsGlan Enable/Disable Glan Port1 Enable B. Glan Port2 EnableCmos Clear Watch Dog Enable/DisableClear Cmos Watch Dog Enable Watch Dog Jumper Settings JWD3rd PWR Supply PWR Fault Jumper Settings 3rd PWR Supply PWR Fault Detect J3PVGA Enable/Disable 3rd PWR Fail B. VGA EnabledJ27 Compact Flash Master/Slave SelectI2C Bus to PCI-X/PCI-Exp. Slots Compact Flash Master/ Slave SelectRear View Onboard IndicatorsOnboard Power LED Glan LEDsOH/Fan Fail LED Overheat LED/Fan Fail JOH1Overheat LED Overheat LED Pin DefinitionsOn the IO panel. See the table on ConnectorParallel Printer Port Parallel printer port is LocatedFloppy Simlp Floppy ConnectorSimlp Slot Compact Flash Card Slot IDE ConnectorsLosing the System’s Setup Configuration Troubleshooting ProceduresBefore Power On No PowerMemory Errors Technical Support ProceduresTroubleshooting System first boots up System configuration Frequently Asked QuestionsReturning Merchandise for Service Bios System BiosHow To Change the Configuration Data Starting the Setup UtilityPress the Delete key to enter Setup Running SetupMain Bios Setup Main Bios Setup Menu IDE Channel 0 Master/Slave and IDE Secondary Master/Slave LBA Mode ControlTransfer Mode Ultra DMA ModeSata Ahci Available when Sata RAID is disabled Sata Controller ModeSerial ATA Sata RAID Enable ICH RAID Code Base Available when Sata RAID is enabledAdvanced Setup Resume On Modem Ring Power Loss ControlMemory Cache Cache System Bios Area Cache Video Bios AreaPCI Configuration Cache Base 512K-640KCache Extended Memory Discrete Mtrr AllocationReset Configuration Data Default Primary Video AdapterEmulated IRQ Solutions PCI Parity Error ForwardingLarge Disk Access Mode Enable MasterLatency Timer 4GB PCI Hole Granularity Serr Signal ConditionMemory Branch Mode Advanced Chipset ControlAMB Thermal Sensor High Temperature Dram OperationCrystal Beach Features Clock Spectrum FeatureLegacy USB Support USB FunctionThermal Management 2 Available when supported by the CPU Frequency Ratio Available when supported by the CPUCore-Multi-Processing Available when supported by the CPU Machine Checking Available when supported by the CPUIntel Eist Support Available when supported by the CPU Hardware Prefetch Available when supported by the CPUDirect Cache Access Available when supported by the CPU DCA Delay Clocks Available when supported by the CPUBase I/O Address I/O Device ConfigurationKBC Clock Input Serial Port aEvent Log Validity DMA ChannelFloppy Disk Controller DMI Event LoggingConsole Type Console RedirectionCOM Port Address Baud RateHardware Monitoring CPU Overheat AlarmPeci Agent 1/2 Temperatures/System Temperature Voltage Monitoring System TemperatureFan1-Fan8 Speeds Fan Speed Control ModesClear System Event Logging Bios Post ErrorsBios Post Watch Dog System Event LoggingTime Out Option OS Boot Watch DogTimer for Loading OS Minutes System Event Log/System Event Log List ModeIPMI LAN Configuration Realtime Sensor DataIP Address Source Default GatewayUpdate LAN Settings Vlan TaggingSecurity Settings Boot Priority Order/Excluded from Boot Orders Boot SettingsExit Page Description Bios Error Beep CodesError Message Beep CodeX7SBi+ User’s Manual Appendix B Installing the Windows OS Page Driver/Tool Installation Display Screen Installing Other DriversAppendix C Installing Other Software Programs and Drivers Configuring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control